mx53: Add Board support for GE PPD

[people/ms/u-boot.git] / include / configs / cm_fx6.h

diff --git a/include/configs/cm_fx6.h b/include/configs/cm_fx6.h
index bbd9f3874953a69afc47aeab0f36d6a9207099b3..da3233e965b4fd7d02059f6487989f6351307a70 100644 (file)
--- a/include/configs/cm_fx6.h
+++ b/include/configs/cm_fx6.h
@@ -17,9 +17,6 @@
 #define CONFIG_SYS_LITTLE_ENDIAN
 #define CONFIG_MACH_TYPE               4273
 
-/* CMD */
-#define CONFIG_CMD_GREPENV
-
 /* MMC */
 #define CONFIG_SYS_FSL_USDHC_NUM       3
 #define CONFIG_SYS_FSL_ESDHC_ADDR      USDHC2_BASE_ADDR
@@ -41,22 +38,22 @@
 /* Serial console */
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE           UART4_BASE
-#define CONFIG_BAUDRATE                        115200
 #define CONFIG_SYS_BAUDRATE_TABLE      {9600, 19200, 38400, 57600, 115200}
 
-/* Shell */
-#define CONFIG_SYS_PROMPT      "CM-FX6 # "
-#define CONFIG_SYS_PBSIZE      (CONFIG_SYS_CBSIZE + \
-                                       sizeof(CONFIG_SYS_PROMPT) + 16)
-
 /* SPI flash */
 #define CONFIG_SF_DEFAULT_BUS          0
 #define CONFIG_SF_DEFAULT_CS           0
 #define CONFIG_SF_DEFAULT_SPEED                25000000
 #define CONFIG_SF_DEFAULT_MODE         (SPI_MODE_0)
 
+/* MTD support */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_SPI_FLASH_MTD
+#endif
+
 /* Environment */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SPI_MAX_HZ          CONFIG_SF_DEFAULT_SPEED
 #define CONFIG_ENV_SPI_MODE            CONFIG_SF_DEFAULT_MODE
 #define CONFIG_ENV_SPI_BUS             CONFIG_SF_DEFAULT_BUS
@@ -71,6 +68,8 @@
        "stderr=serial,vga\0" \
        "panel=HDMI\0" \
        "autoload=no\0" \
+       "uImage=uImage-cm-fx6\0" \
+       "zImage=zImage-cm-fx6\0" \
        "kernel=uImage-cm-fx6\0" \
        "script=boot.scr\0" \
        "dtb=cm-fx6.dtb\0" \
@@ -83,10 +82,12 @@
        "video_dvi=mxcfb0:dev=dvi,1280x800M-32@50,if=RGB32\0" \
        "doboot=bootm ${loadaddr}\0" \
        "doloadfdt=false\0" \
-       "setboottypez=setenv kernel zImage-cm-fx6;" \
+       "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+       "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
+       "setboottypez=setenv kernel ${zImage};" \
                "setenv doboot bootz ${loadaddr} - ${fdtaddr};" \
                "setenv doloadfdt true;\0" \
-       "setboottypem=setenv kernel uImage-cm-fx6;" \
+       "setboottypem=setenv kernel ${uImage};" \
                "setenv doboot bootm ${loadaddr};" \
                "setenv doloadfdt false;\0"\
        "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
@@ -94,13 +95,13 @@
        "nandroot=/dev/mtdblock4 rw\0" \
        "nandrootfstype=ubifs\0" \
        "mmcargs=setenv bootargs console=${console} root=${mmcroot} " \
-               "${video}\0" \
+               "${video} ${extrabootargs}\0" \
        "sataargs=setenv bootargs console=${console} root=${sataroot} " \
-               "${video}\0" \
+               "${video} ${extrabootargs}\0" \
        "nandargs=setenv bootargs console=${console} " \
                "root=${nandroot} " \
                "rootfstype=${nandrootfstype} " \
-               "${video}\0" \
+               "${video} ${extrabootargs}\0" \
        "nandboot=if run nandloadkernel; then " \
                        "run nandloadfdt;" \
                        "run setboottypem;" \
@@ -157,7 +158,7 @@
        "run setupnandboot;" \
        "run nandboot;"
 
-#define CONFIG_PREBOOT         "usb start"
+#define CONFIG_PREBOOT         "usb start;sf probe"
 
 /* SPI */
 #define CONFIG_SPI
@@ -165,7 +166,6 @@
 
 /* NAND */
 #ifndef CONFIG_SPL_BUILD
-#define CONFIG_CMD_NAND
 #define CONFIG_SYS_NAND_BASE           0x40000000
 #define CONFIG_SYS_NAND_MAX_CHIPS      1
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
@@ -182,7 +182,6 @@
 #define CONFIG_FEC_MXC_PHYADDR         0
 #define CONFIG_FEC_XCV_TYPE            RGMII
 #define IMX_FEC_BASE                   ENET_BASE_ADDR
-#define CONFIG_PHYLIB
 #define CONFIG_PHY_ATHEROS
 #define CONFIG_MII
 #define CONFIG_ETHPRIME                        "FEC0"
@@ -194,11 +193,12 @@
 #define CONFIG_MXC_USB_FLAGS           0
 #define CONFIG_USB_MAX_CONTROLLER_COUNT        2
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET       /* For OTG port */
-#define CONFIG_SYS_STDIO_DEREGISTER
 
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1                /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2                /* enable I2C bus 2 */
 #define CONFIG_SYS_I2C_MXC_I2C3                /* enable I2C bus 3 */
 #define CONFIG_SYS_I2C_SPEED           100000
 #define CONFIG_SYS_MXC_I2C3_SPEED      400000
@@ -208,7 +208,6 @@
 #define CONFIG_SYS_I2C_EEPROM_BUS      2
 
 /* SATA */
-#define CONFIG_CMD_SATA
 #define CONFIG_SYS_SATA_MAX_DEVICE     1
 #define CONFIG_LIBATA
 #define CONFIG_LBA48
@@ -221,39 +220,30 @@
 #define CONFIG_SERIAL_TAG
 
 /* misc */
-#define CONFIG_STACKSIZE                       (128 * 1024)
 #define CONFIG_SYS_MALLOC_LEN                  (10 * 1024 * 1024)
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS     800 /* 400 KB */
-#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_MISC_INIT_R
 
 /* SPL */
 #include "imx6_spl.h"
-#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR        0x80 /* offset 64 kb */
-#define CONFIG_SYS_MONITOR_LEN (CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS / 2 * 1024)
-#define CONFIG_SPL_SPI_SUPPORT
-#define CONFIG_SPL_SPI_FLASH_SUPPORT
 #define CONFIG_SYS_SPI_U_BOOT_OFFS     (64 * 1024)
 #define CONFIG_SPL_SPI_LOAD
 
 /* Display */
-#define CONFIG_VIDEO
 #define CONFIG_VIDEO_IPUV3
-#define CONFIG_IPUV3_CLK          260000000
 #define CONFIG_IMX_HDMI
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_CONSOLE_MUX
-#define CONFIG_VIDEO_SW_CURSOR
 
 #define CONFIG_SPLASH_SCREEN
 #define CONFIG_SPLASH_SOURCE
-#define CONFIG_CMD_BMP
 #define CONFIG_VIDEO_BMP_RLE8
 
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_LOGO
 
+/* EEPROM */
+#define CONFIG_ENV_EEPROM_IS_ON_I2C
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  5
+#define CONFIG_SYS_EEPROM_SIZE                 256
+
 #endif /* __CONFIG_CM_FX6_H */