Convert CONFIG_CMD_EEPROM et al to Kconfig

[people/ms/u-boot.git] / include / configs / cm_t54.h

diff --git a/include/configs/cm_t54.h b/include/configs/cm_t54.h
index 641ab48c2c81d5fd7203905d18c6efec619d05d5..14042ada7d07373b5770ac0d3cdb8f9edae1783c 100644 (file)
--- a/include/configs/cm_t54.h
+++ b/include/configs/cm_t54.h
@@ -16,16 +16,6 @@
 
 #include <configs/ti_omap5_common.h>
 
-#undef CONFIG_MISC_INIT_R
-#undef CONFIG_SPL_OS_BOOT
-
-/* Enable Generic board */
-#define CONFIG_SYS_GENERIC_BOARD
-
-/* Device Tree defines */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-
 /* EEPROM related defines */
 #define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50
@@ -38,14 +28,6 @@
 /* UART setup */
 #define CONFIG_CONS_INDEX              4
 #define CONFIG_SYS_NS16550_COM4                UART4_BASE
-#define CONFIG_BAUDRATE                        115200
-
-/* SD/MMC RAW boot */
-#undef CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
-#undef CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS
-
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR        0x200 /* 0x40000 - 256 KB */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS     0x300 /* 384 KB */
 
 /* MMC ENV related defines */
 #undef CONFIG_ENV_OFFSET
@@ -58,18 +40,24 @@
 #define CONFIG_ENV_SIZE                        (16 << 10)      /* 16 KB */
 #define CONFIG_ENV_OFFSET_REDUND       (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_CMD_SAVEENV
 
 /* Enhance our eMMC support / experience. */
 #define CONFIG_HSMMC2_8BIT
 #define CONFIG_SUPPORT_EMMC_BOOT
 
+/* SATA Boot related defines */
+#define CONFIG_SPL_SATA_BOOT_DEVICE            0
+#define CONFIG_SYS_SATA_FAT_BOOT_PARTITION     1
+
+#define CONFIG_SCSI
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID    1
+#define CONFIG_SYS_SCSI_MAX_LUN                1
+#define CONFIG_SYS_SCSI_MAX_DEVICE     (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+                                               CONFIG_SYS_SCSI_MAX_LUN)
 /* USB UHH support options */
-#define CONFIG_CMD_USB
-#define CONFIG_USB_HOST
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
-#define CONFIG_USB_STORAGE
 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS     3
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 
@@ -77,9 +65,13 @@
 #define CONFIG_OMAP_EHCI_PHY3_RESET_GPIO       83 /* HSIC3 ETH #RESET */
 
 /* Enabled commands */
-#define CONFIG_CMD_DHCP                /* DHCP Support                 */
-#define CONFIG_CMD_NET         /* bootp, tftpboot, rarpboot    */
-#define CONFIG_CMD_PING
+
+/* EEPROM */
+#define CONFIG_ENV_EEPROM_IS_ON_I2C
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  5
+#define CONFIG_SYS_EEPROM_SIZE                 256
 
 /* USB Networking options */
 #define CONFIG_USB_HOST_ETHER
@@ -88,21 +80,14 @@
 #define CONFIG_USB_ETHER_ASIX
 #define CONFIG_USB_ETHER_MCS7830
 
-/* Max time to hold reset on this board, see doc/README.omap-reset-time */
-#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC       16296
-
 /*
  * Miscellaneous configurable options
  */
 #undef CONFIG_SYS_AUTOLOAD
-#undef CONFIG_SYS_PROMPT
 #undef CONFIG_EXTRA_ENV_SETTINGS
 #undef CONFIG_BOOTCOMMAND
-#undef CONFIG_BOOTDELAY
 
-#define CONFIG_BOOTDELAY               3
 #define CONFIG_SYS_AUTOLOAD            "no"
-#define CONFIG_SYS_PROMPT              "CM-T54 # "
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
        DEFAULT_LINUX_BOOT_ENV \