Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

[people/ms/u-boot.git] / include / configs / cobra5272.h

diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h
index 885dfd476166b9a2ad1b81ec69023e1293229ca4..ee870f916f559fcf13677e0d47e3a3da4ce2579b 100644 (file)
--- a/include/configs/cobra5272.h
+++ b/include/configs/cobra5272.h
@@ -3,11 +3,11 @@
  *
  * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
  *
- * SPDX-License-Identifier:    GPL-2.0+ 
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /* ---
- * Version: U-boot 1.0.0 - initial release for Sentec COBRA5272 board
+ * Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board
  * Date: 2004-03-29
  * Author: Florian Schlote
  *
@@ -24,24 +24,12 @@
 #ifndef _CONFIG_COBRA5272_H
 #define _CONFIG_COBRA5272_H
 
-/* ---
- * Define processor
- * possible values for Sentec board: only Coldfire M5272 processor supported
- * (please do not change)
- * ---
- */
-
-#define CONFIG_MCF52x2                 /* define processor family */
-#define CONFIG_M5272                   /* define processor type */
-
 /* ---
  * Defines processor clock - important for correct timings concerning serial
  * interface etc.
- * CONFIG_SYS_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms
  * ---
  */
 
-#define CONFIG_SYS_HZ                  1000
 #define CONFIG_SYS_CLK                 66000000
 #define CONFIG_SYS_SDRAM_SIZE          16              /* SDRAM size in MB */
 
@@ -64,7 +52,6 @@
 
 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT           (0)
-#define CONFIG_BAUDRATE                19200
 
 /* ---
  * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
@@ -109,33 +96,23 @@
 #ifndef CONFIG_MONITOR_IS_IN_RAM
 #define CONFIG_ENV_OFFSET              0x4000
 #define CONFIG_ENV_SECT_SIZE   0x2000
-#define CONFIG_ENV_IS_IN_FLASH 1
 #else
 #define CONFIG_ENV_ADDR                0xffe04000
 #define CONFIG_ENV_SECT_SIZE   0x2000
-#define CONFIG_ENV_IS_IN_FLASH 1
 #endif
 
+#define LDS_BOARD_TEXT \
+       . = DEFINED(env_offset) ? env_offset : .; \
+       env/embedded.o(.text);
 
 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
 
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_LOADB
-#undef CONFIG_CMD_MII
 
 #ifdef CONFIG_MCFFEC
 #      define CONFIG_MII               1
@@ -166,12 +143,6 @@
 
 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/
 
-#define CONFIG_BOOTDELAY       5               /* used for autoboot, delay in
-seconds u-boot will wait before starting defined (auto-)boot command, setting
-to -1 disables delay, setting to 0 will too prevent access to u-boot command
-interface: u-boot then has to reflashed */
-
-
 /* The following settings will be contained in the environment block ; if you
 want to use a neutral environment all those settings can be manually set in
 u-boot: 'set' command */
@@ -181,35 +152,18 @@ u-boot: 'set' command */
 #define CONFIG_BOOTCOMMAND     "bootm 0xffe80000"      /*Autoboto command, please
 enter a valid image address in flash */
 
-#define CONFIG_BOOTARGS                " "                     /* default bootargs that are
-considered during boot */
-
 /* User network settings */
 
-#define CONFIG_ETHADDR 00:00:00:00:00:09       /* default ethernet MAC addr. */
 #define CONFIG_IPADDR 192.168.100.2            /* default board IP address */
 #define CONFIG_SERVERIP 192.168.100.1  /* default tftp server IP address */
 
 #endif
 
-#define CONFIG_SYS_PROMPT              "COBRA > "      /* Layout of u-boot prompt*/
-
 #define CONFIG_SYS_LOAD_ADDR           0x20000         /*Defines default RAM address
 from which user programs will be started */
 
 /*---*/
 
-#define CONFIG_SYS_LONGHELP                            /* undef to save memory         */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE              1024            /* Console I/O Buffer Size      */
-#else
-#define CONFIG_SYS_CBSIZE              256             /* Console I/O Buffer Size      */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS             16              /* max number of command args   */
-#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
-
 /*
  *-----------------------------------------------------------------------------
  * End of user parameters to be customized