Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

[people/ms/u-boot.git] / include / configs / devkit3250.h

diff --git a/include/configs/devkit3250.h b/include/configs/devkit3250.h
index 99d91486113f4495595509ec77279725788215e7..40dee673871cbe2924f3e53e30c1aa1ad08b11b5 100644 (file)
--- a/include/configs/devkit3250.h
+++ b/include/configs/devkit3250.h
@@ -13,10 +13,6 @@
 #include <linux/sizes.h>
 #include <asm/arch/cpu.h>
 
-/*
- * Define DevKit3250 machine type by hand until it lands in mach-types
- */
-#define MACH_TYPE_DEVKIT3250           3697
 #define CONFIG_MACH_TYPE               MACH_TYPE_DEVKIT3250
 
 #define CONFIG_SYS_ICACHE_OFF
@@ -24,7 +20,6 @@
 #if !defined(CONFIG_SPL_BUILD)
 #define CONFIG_SKIP_LOWLEVEL_INIT
 #endif
-#define CONFIG_BOARD_EARLY_INIT_F
 
 /*
  * Memory configurations
@@ -33,7 +28,6 @@
 #define CONFIG_SYS_MALLOC_LEN          SZ_1M
 #define CONFIG_SYS_SDRAM_BASE          EMC_DYCS0_BASE
 #define CONFIG_SYS_SDRAM_SIZE          SZ_64M
-#define CONFIG_SYS_TEXT_BASE           0x83F00000
 #define CONFIG_SYS_MEMTEST_START       (CONFIG_SYS_SDRAM_BASE + SZ_32K)
 #define CONFIG_SYS_MEMTEST_END         (CONFIG_SYS_TEXT_BASE - SZ_1M)
 
@@ -46,7 +40,6 @@
  * Serial Driver
  */
 #define CONFIG_SYS_LPC32XX_UART                5   /* UART5 */
-#define CONFIG_BAUDRATE                        115200
 
 /*
  * DMA
@@ -61,7 +54,6 @@
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_LPC32XX
 #define CONFIG_SYS_I2C_SPEED           100000
-#define CONFIG_CMD_I2C
 
 /*
  * GPIO
@@ -71,9 +63,7 @@
 /*
  * SSP/SPI
  */
-#define CONFIG_LPC32XX_SSP
 #define CONFIG_LPC32XX_SSP_TIMEOUT     100000
-#define CONFIG_CMD_SPI
 
 /*
  * Ethernet
@@ -81,12 +71,8 @@
 #define CONFIG_RMII
 #define CONFIG_PHY_SMSC
 #define CONFIG_LPC32XX_ETH
-#define CONFIG_PHYLIB
 #define CONFIG_PHY_ADDR                        0x1F
 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
 
 /*
  * NOR Flash
@@ -121,43 +107,25 @@
 #define CONFIG_SYS_NAND_PAGE_SIZE              NAND_LARGE_BLOCK_PAGE_SIZE
 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NAND
-
 /*
  * USB
  */
 #define CONFIG_USB_OHCI_LPC32XX
 #define CONFIG_USB_ISP1301_I2C_ADDR            0x2d
-#define CONFIG_USB_STORAGE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_USB
 
 /*
  * U-Boot General Configurations
  */
-#define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_CBSIZE              1024
-#define CONFIG_SYS_PBSIZE              \
-       (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS             16
 #define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE
 
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DOS_PARTITION
-
 /*
  * Pass open firmware flat tree
  */
-#define CONFIG_OF_LIBFDT
 
 /*
  * Environment
  */
-#define CONFIG_ENV_IS_IN_NAND          1
 #define CONFIG_ENV_SIZE                        SZ_128K
 #define CONFIG_ENV_OFFSET              0x000A0000
 
@@ -180,18 +148,14 @@
 /*
  * U-Boot Commands
  */
-#define CONFIG_CMD_CACHE
 
 /*
  * Boot Linux
  */
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_BOOTDELAY               1
 
 #define CONFIG_BOOTFILE                        "uImage"
-#define CONFIG_BOOTARGS                        "console=ttyS0,115200n8"
 #define CONFIG_LOADADDR                        0x80008000
 
 /*
@@ -202,20 +166,13 @@
 
 /* SPL will use SRAM as stack */
 #define CONFIG_SPL_STACK               0x0000FFF8
-#define CONFIG_SPL_BOARD_INIT
 
 /* Use the framework and generic lib */
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
 
 /* SPL will use serial */
-#define CONFIG_SPL_SERIAL_SUPPORT
 
 /* SPL loads an image from NAND */
-#define CONFIG_SPL_NAND_SIMPLE
 #define CONFIG_SPL_NAND_RAW_ONLY
-#define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_NAND_DRIVERS
 
 #define CONFIG_SPL_NAND_ECC