#define CONFIG_REVISION_TAG
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
-#define CONFIG_MXC_GPIO
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_IMX_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT_MSECS 6000
+
+#define CONFIG_LAST_STAGE_INIT
+
#define CONFIG_MXC_UART
#define CONFIG_MXC_OCOTP
/* SATA Configs */
#ifdef CONFIG_CMD_SATA
-#define CONFIG_DWC_AHSATA
#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
-#define CONFIG_LIBATA
#endif
/* MMC Configs */
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
-#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
-#define CONFIG_CI_UDC
#define CONFIG_USBD_HS
-#define CONFIG_USB_GADGET_DUALSPEED
-#define CONFIG_USB_GADGET
-#define CONFIG_USB_GADGET_DOWNLOAD
#define CONFIG_USB_GADGET_MASS_STORAGE
-#define CONFIG_USB_FUNCTION_MASS_STORAGE
-#define CONFIG_USB_GADGET_VBUS_DRAW 2
-#define CONFIG_G_DNL_VENDOR_NUM 0x0525
-#define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5
-#define CONFIG_G_DNL_MANUFACTURER "Advantech"
#endif
/* Networking Configs */
/* Serial Flash */
#ifdef CONFIG_CMD_SF
-#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_CONS_INDEX 1
#define CONFIG_LOADADDR 0x12000000
-#define CONFIG_SYS_TEXT_BASE 0x17800000
#define CONFIG_EXTRA_ENV_SETTINGS \
- "script=boot.scr\0" \
- "image=/boot/uImage\0" \
- "uboot=u-boot.imx\0" \
- "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
- "fdt_addr=0x18000000\0" \
- "boot_fdt=yes\0" \
- "ip_dyn=yes\0" \
+ "bootcause=POR\0" \
+ "bootlimit=10\0" \
+ "image=/boot/fitImage\0" \
+ "fdt_high=0xffffffff\0" \
+ "dev=mmc\0" \
+ "devnum=1\0" \
+ "rootdev=mmcblk0p\0" \
+ "quiet=quiet loglevel=0\0" \
"console=" CONSOLE_DEV "\0" \
- "fdt_high=0xffffffff\0" \
- "initrd_high=0xffffffff\0" \
- "sddev=0\0" \
- "emmcdev=1\0" \
- "partnum=1\0" \
- "update_sd_firmware=" \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "if mmc dev ${mmcdev}; then " \
- "if ${get_cmd} ${update_sd_firmware_filename}; then " \
- "setexpr fw_sz ${filesize} / 0x200; " \
- "setexpr fw_sz ${fw_sz} + 1; " \
- "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
- "fi; " \
- "fi\0" \
- "update_sf_uboot=" \
- "if tftp $loadaddr $uboot; then " \
- "sf probe; " \
- "sf erase 0 0xC0000; " \
- "sf write $loadaddr 0x400 $filesize; " \
- "echo 'U-Boot upgraded. Please reset'; " \
- "fi\0" \
- "setargs=setenv bootargs console=${console},${baudrate} " \
- "root=/dev/${rootdev} rw rootwait cma=128M " \
+ "setargs=setenv bootargs root=/dev/${rootdev}${partnum} " \
+ "ro rootwait cma=128M " \
+ "bootcause=${bootcause} " \
+ "${quiet} console=${console} ${rtc_status} " \
BX50V3_BOOTARGS_EXTRA "\0" \
- "loadbootscript=" \
- "ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
- " source\0" \
+ "doquiet=" \
+ "if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
+ "then setenv quiet; fi\0" \
+ "hasfirstboot=" \
+ "ext2load ${dev} ${devnum}:${partnum} 0x7000A000 " \
+ "/boot/bootcause/firstboot\0" \
+ "swappartitions=" \
+ "setexpr partnum 3 - ${partnum}\0" \
+ "failbootcmd=" \
+ "msg=\"Monitor failed to start. Try again, or contact GE Service for support.\"; " \
+ "echo $msg; " \
+ "setenv stdout vga; " \
+ "echo \"\n\n\n\n \" $msg; " \
+ "setenv stdout serial; " \
+ "mw.b 0x7000A000 0xbc; " \
+ "mw.b 0x7000A001 0x00; " \
+ "ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
+ "altbootcmd=" \
+ "run doquiet; " \
+ "setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
+ "run hasfirstboot || setenv partnum 0; " \
+ "if test ${partnum} != 0; then " \
+ "setenv bootcause REVERT; " \
+ "run swappartitions loadimage doboot; " \
+ "fi; " \
+ "run failbootcmd\0" \
"loadimage=" \
"ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
- "loadfdt=ext2load ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
- "tryboot=" \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadimage; then " \
- "run doboot; " \
- "fi; " \
- "fi;\0" \
- "doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
+ "doboot=" \
+ "echo Booting from ${dev}:${devnum}:${partnum} ...; " \
"run setargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootm; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootm; " \
- "fi;\0" \
- "netargs=setenv bootargs console=${console},${baudrate} " \
- "root=/dev/nfs " \
- "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
- "netboot=echo Booting from net ...; " \
- "run netargs; " \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "${get_cmd} ${image}; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootm; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootm; " \
- "fi;\0" \
+ "bootm ${loadaddr}#conf@${confidx}\0" \
+ "tryboot=" \
+ "setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
+ "run loadimage || run swappartitions && run loadimage || " \
+ "setenv partnum 0 && echo MISSING IMAGE;" \
+ "run doboot; " \
+ "run failbootcmd\0" \
#define CONFIG_MMCBOOTCOMMAND \
- "setenv dev mmc; " \
- "setenv rootdev mmcblk0p${partnum}; " \
- \
- "setenv devnum ${sddev}; " \
- "if mmc dev ${devnum}; then " \
- "run tryboot; " \
- "setenv rootdev mmcblk1p${partnum}; " \
- "fi; " \
- \
- "setenv devnum ${emmcdev}; " \
"if mmc dev ${devnum}; then " \
+ "run doquiet; " \
"run tryboot; " \
"fi; " \
#define CONFIG_USBBOOTCOMMAND \
- "usb start; " \
- "setenv dev usb; " \
- "setenv devnum 0; " \
- "setenv rootdev sda${partnum}; " \
- "run tryboot; " \
- \
- CONFIG_MMCBOOTCOMMAND \
- "bmode usb; " \
+ "echo Unsupported; " \
#ifdef CONFIG_CMD_USB
#define CONFIG_BOOTCOMMAND CONFIG_USBBOOTCOMMAND
#define CONFIG_SYS_LONGHELP
#define CONFIG_AUTO_COMPLETE
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
#define CONFIG_SYS_MEMTEST_START 0x10000000
#define CONFIG_SYS_MEMTEST_END 0x10010000
#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
#define CONFIG_SYS_FSL_USDHC_NUM 3
/* Framebuffer */
+#define CONFIG_VIDEO
#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_IPUV3
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_BMP_16BPP
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_IPUV3_CLK 260000000
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_FG_COL 0xFF
+#define CONFIG_SYS_CONSOLE_BG_COL 0x00
+#define CONFIG_HIDE_LOGO_VERSION
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP
+#define CONFIG_CMD_BMP
#endif
#define CONFIG_PWM_IMX
#define CONFIG_IMX6_PWM_PER_CLK 66000000
-#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI
+#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_PCIE_IMX
#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12)
#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5)
-#endif
+
+#define CONFIG_RTC_RX8010SJ
+#define CONFIG_SYS_RTC_BUS_NUM 2
+#define CONFIG_SYS_I2C_RTC_ADDR 0x32
/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC_I2C2
#define CONFIG_SYS_I2C_MXC_I2C3
+#define CONFIG_SYS_NUM_I2C_BUSES 11
+#define CONFIG_SYS_I2C_MAX_HOPS 1
+#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
+ {1, {I2C_NULL_HOP} }, \
+ {2, {I2C_NULL_HOP} }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \
+ }
+
+#define CONFIG_BCH
+
+#define CONFIG_BOOTCOUNT_EXT
+#define CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE "mmc"
+#define CONFIG_SYS_BOOTCOUNT_EXT_DEVPART "1:5"
+#define CONFIG_SYS_BOOTCOUNT_EXT_NAME "/boot/failures"
+#define CONFIG_SYS_BOOTCOUNT_ADDR 0x7000A000
+
#endif /* __GE_BX50V3_CONFIG_H */
projects / people / ms / u-boot.git / blobdiff