Kconfig: Move config IDENT_STRING to Kconfig

[people/ms/u-boot.git] / include / configs / gr_ep2s60.h

diff --git a/include/configs/gr_ep2s60.h b/include/configs/gr_ep2s60.h
index 7c320eeb64c29b94489ece916c5629dd1802e9a7..fa10676a44bbf55d9aca6103eeaad124f9b5f1c4 100644 (file)
--- a/include/configs/gr_ep2s60.h
+++ b/include/configs/gr_ep2s60.h
@@ -15,6 +15,8 @@
 #ifndef __CONFIG_H__
 #define __CONFIG_H__
 
+#define CONFIG_DISPLAY_BOARDINFO
+
 /*
  * High Level Configuration Options
  * (easy to change)
@@ -26,9 +28,6 @@
 /* CPU / AMBA BUS configuration */
 #define CONFIG_SYS_CLK_FREQ    96000000        /* 96MHz */
 
-/* Number of SPARC register windows */
-#define CONFIG_SYS_SPARC_NWINDOWS 8
-
 /* Define this is the GR-2S60-MEZZ mezzanine is available and you
  * want to use the USB and GRETH functionality of the board
  */
@@ -53,21 +52,13 @@
 /*
  * Supported commands
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_AMBAPP
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_DIAG
 #define CONFIG_CMD_IRQ
 
 /* USB support */
 #if USE_GRUSB
 #define CONFIG_USB_UHCI
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
 /* Enable needed helper functions */
 #define CONFIG_SYS_STDIO_DEREGISTER    /* needs stdio_deregister */
 #endif
@@ -75,7 +66,6 @@
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY       5       /* autoboot after 5 seconds */
 
 #define CONFIG_PREBOOT "echo;" \
        "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
@@ -259,6 +249,7 @@
 
 /* USE GRETH Ethernet Driver */
 #define CONFIG_GRETH   1
+#endif
 
 #define CONFIG_PHY_ADDR         0x00
 
@@ -289,33 +280,31 @@
 
 /***** Gaisler GRLIB IP-Cores Config ********/
 
-/* AMBA Plug & Play info display on startup */
-/*#define CONFIG_SYS_AMBAPP_PRINT_ON_STARTUP*/
-
 #define CONFIG_SYS_GRLIB_SDRAM    0
 
+/* No SDRAM Configuration */
+#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
+
 /* See, GRLIB Docs (grip.pdf) on how to set up
  * These the memory controller registers.
  */
-#define CONFIG_SYS_GRLIB_MEMCFG1  (0x10f800ff | (1<<11))
-#define CONFIG_SYS_GRLIB_MEMCFG2  0x00000000
-#define CONFIG_SYS_GRLIB_MEMCFG3  0x00000000
-
-#define CONFIG_SYS_GRLIB_FT_MEMCFG1  (0x10f800ff | (1<<11))
-#define CONFIG_SYS_GRLIB_FT_MEMCFG2  0x00000000
-#define CONFIG_SYS_GRLIB_FT_MEMCFG3  0x00000000
-
-#define CONFIG_SYS_GRLIB_DDR_CFG  0xa900830a
-
-#define CONFIG_SYS_GRLIB_DDR2_CFG1 0x00000000
-#define CONFIG_SYS_GRLIB_DDR2_CFG3 0x00000000
-
-/* Calculate scaler register value from default baudrate */
-#define CONFIG_SYS_GRLIB_APBUART_SCALER \
- ((((CONFIG_SYS_CLK_FREQ*10)/(CONFIG_BAUDRATE*8))-5)/10)
-
-/* Identification string */
-#define CONFIG_IDENT_STRING "GAISLER LEON3 EP2S60"
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1  (0x10f800ff | (1<<11))
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2  0x00000000
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3  0x00000000
+
+/* GRLIB FT-MCTRL configuration */
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1  (0x10f800ff | (1<<11))
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2  0x00000000
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3  0x00000000
+
+/* DDR controller */
+#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
+#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1_CTRL  0xa900830a
+
+/* no DDR2 Controller */
+#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
 
 /* default kernel command line */
 #define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"