drivers, block: remove sil680 driver

[people/ms/u-boot.git] / include / configs / intip.h

diff --git a/include/configs/intip.h b/include/configs/intip.h
index d3d7a441b6b307c7a512ed18829c4b9019b27e9f..036fd20eb46a0f9373c13c3b1338277d06b6e544 100644 (file)
--- a/include/configs/intip.h
+++ b/include/configs/intip.h
@@ -24,13 +24,10 @@
 #define CONFIG_460EX           1       /* Specific PPC460EX            */
 #ifdef CONFIG_DEVCONCENTER
 #define CONFIG_HOSTNAME                devconcenter
-#define CONFIG_IDENT_STRING    " devconcenter 0.06"
 #else
 #define CONFIG_HOSTNAME                intip
-#define CONFIG_IDENT_STRING    " intip 0.06"
 #endif
 #define CONFIG_440             1
-#define CONFIG_4xx             1       /* ... PPC4xx family */
 
 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE   0xFFFA0000
@@ -43,17 +40,11 @@
 
 #define CONFIG_SYS_CLK_FREQ    66666667        /* external freq to pll */
 
-#define CONFIG_BOARD_EARLY_INIT_F      1       /* Call board_early_init_f */
 #define CONFIG_BOARD_EARLY_INIT_R      1       /* Call board_early_init_r */
 #define CONFIG_MISC_INIT_R             1       /* Call misc_init_r */
 #define CONFIG_BOARD_TYPES             1       /* support board types */
-#define CONFIG_FIT
 #define CFG_ALT_MEMTEST
 
-#undef CONFIG_ZERO_BOOTDELAY_CHECK     /* ignore keypress on bootdelay==0 */
-#define CONFIG_AUTOBOOT_KEYED          /* use key strings to stop autoboot */
-#define CONFIG_AUTOBOOT_STOP_STR " "
-
 /*
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
@@ -217,7 +208,6 @@
  */
 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0          400000
 
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR             (0xa8>>1)
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      3
@@ -228,13 +218,6 @@
 #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET    0
 #define CONFIG_4xx_CONFIG_BLOCKSIZE            16
 
-/* I2C SYSMON */
-#define CONFIG_DTT_LM63         1       /* National LM63        */
-#define CONFIG_DTT_SENSORS      { 0 }   /* Sensor addresses     */
-#define CONFIG_DTT_PWM_LOOKUPTABLE      \
-       { { 40, 10 }, { 50, 20 }, { 60, 40 } }
-#define CONFIG_DTT_TACH_LIMIT   0xa10
-
 /* RTC configuration */
 #define CONFIG_RTC_DS1337      1
 #define CONFIG_SYS_I2C_RTC_ADDR        0x68
@@ -258,7 +241,6 @@
  * USB-OHCI
  */
 #define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_STORAGE
 #undef CONFIG_SYS_OHCI_BE_CONTROLLER   /* 460EX has little endian descriptors*/
 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS        /* 460EX has little endian register */
 #define CONFIG_SYS_OHCI_USE_NPS                /* force NoPowerSwitching mode */
@@ -283,28 +265,16 @@
 /*
  * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_CMD_CHIP_CONFIG
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_USB
 
 /* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
 
 /*
  * PCI stuff
  */
 /* General PCI */
-#define CONFIG_PCI                     /* include pci support          */
 #define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
-#define CONFIG_PCI_PNP                 /* do pci plug-and-play   */
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup  */
 #define CONFIG_PCI_CONFIG_HOST_BRIDGE
 #define CONFIG_PCI_DISABLE_PCIE
@@ -316,7 +286,6 @@
 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014  /* IBM */
 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe  /* Whatever */
 
-
 /*
  * External Bus Controller (EBC) Setup
  */
@@ -331,7 +300,6 @@
  * 0xfc00.0000 -> 4.cc00.0000
  */
 
-
 /* Memory Bank 0 (NOR-FLASH) initialization */
 #define CONFIG_SYS_EBC_PB0AP           0x10055e00
 #define CONFIG_SYS_EBC_PB0CR           (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000)