drivers/pci/Kconfig: Add PCI

[people/ms/u-boot.git] / include / configs / intip.h

diff --git a/include/configs/intip.h b/include/configs/intip.h
index 18d314006fbd5c380dd199c77c235185a54224c6..3ecf47d866ce3ed8ab01d00819838115175655da 100644 (file)
--- a/include/configs/intip.h
+++ b/include/configs/intip.h
@@ -24,10 +24,8 @@
 #define CONFIG_460EX           1       /* Specific PPC460EX            */
 #ifdef CONFIG_DEVCONCENTER
 #define CONFIG_HOSTNAME                devconcenter
-#define CONFIG_IDENT_STRING    " devconcenter 0.06"
 #else
 #define CONFIG_HOSTNAME                intip
-#define CONFIG_IDENT_STRING    " intip 0.06"
 #endif
 #define CONFIG_440             1
 
@@ -45,13 +43,9 @@
 #define CONFIG_BOARD_EARLY_INIT_F      1       /* Call board_early_init_f */
 #define CONFIG_BOARD_EARLY_INIT_R      1       /* Call board_early_init_r */
 #define CONFIG_MISC_INIT_R             1       /* Call misc_init_r */
-#define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_BOARD_TYPES             1       /* support board types */
-#define CONFIG_FIT
 #define CFG_ALT_MEMTEST
 
-#undef CONFIG_ZERO_BOOTDELAY_CHECK     /* ignore keypress on bootdelay==0 */
-
 /*
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
@@ -215,7 +209,6 @@
  */
 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0          400000
 
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR             (0xa8>>1)
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      3
@@ -256,7 +249,6 @@
  * USB-OHCI
  */
 #define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_STORAGE
 #undef CONFIG_SYS_OHCI_BE_CONTROLLER   /* 460EX has little endian descriptors*/
 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS        /* 460EX has little endian register */
 #define CONFIG_SYS_OHCI_USE_NPS                /* force NoPowerSwitching mode */
@@ -284,12 +276,8 @@
 #define CONFIG_CMD_CHIP_CONFIG
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DTT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_USB
 
 /* Partitions */
 #define CONFIG_MAC_PARTITION
@@ -300,7 +288,6 @@
  * PCI stuff
  */
 /* General PCI */
-#define CONFIG_PCI                     /* include pci support          */
 #define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play   */
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup  */
@@ -314,7 +301,6 @@
 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014  /* IBM */
 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe  /* Whatever */
 
-
 /*
  * External Bus Controller (EBC) Setup
  */
@@ -329,7 +315,6 @@
  * 0xfc00.0000 -> 4.cc00.0000
  */
 
-
 /* Memory Bank 0 (NOR-FLASH) initialization */
 #define CONFIG_SYS_EBC_PB0AP           0x10055e00
 #define CONFIG_SYS_EBC_PB0CR           (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000)