#ifndef _CONFIG_KMP204X_H
#define _CONFIG_KMP204X_H
-#define CONFIG_PHYS_64BIT
#define CONFIG_PPC_P2041
-#define CONFIG_SYS_TEXT_BASE 0xfff80000
+#define CONFIG_SYS_TEXT_BASE 0xfff40000
#define CONFIG_KM_DEF_NETDEV "netdev=eth0\0"
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
-#define CONFIG_PCI /* Enable PCI/PCIE */
-#define CONFIG_PCIE1 /* PCIE controler 1 */
-#define CONFIG_PCIE3 /* PCIE controler 3 */
+#define CONFIG_PCIE1 /* PCIE controller 1 */
+#define CONFIG_PCIE3 /* PCIE controller 3 */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
-#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00800000
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
+#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */
/*
* Config the L3 Cache as L3 SRAM
#define CONFIG_KM_PNVRAM 0x80000
/* physical RAM MTD size [hex] */
#define CONFIG_KM_PHRAM 0x100000
-/* resereved pram area at the end of memroy [hex] */
-#define CONFIG_KM_RESERVED_PRAM 0x0
-/* enable protected RAM */
-#define CONFIG_PRAM 0
+/* reserved pram area at the end of memory [hex]
+ * u-boot reserves some memory for the MP boot page */
+#define CONFIG_KM_RESERVED_PRAM 0x1000
+/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
+ * is not valid yet, which is the case for when u-boot copies itself to RAM */
+#define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10)
#define CONFIG_KM_CRAMFS_ADDR 0x2000000
#define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
/* Serial Port - controlled on board with jumper J8
* shorted - index 1
*/
#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
-
/* I2C */
#define CONFIG_SYS_I2C
/*
* eSPI - Enhanced SPI
*/
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_SPI_FLASH_SPANSION
-#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE 0
#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
+#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
+#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
+#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
+ CONFIG_SYS_BMAN_CENA_SIZE)
+#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
#define CONFIG_SYS_QMAN_NUM_PORTALS 10
#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
+#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
+#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
+#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
+ CONFIG_SYS_QMAN_CENA_SIZE)
+#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_E1000
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+/*
+ * Hardware Watchdog
+ */
+#define CONFIG_WATCHDOG /* enable CPU watchdog */
+#define CONFIG_WATCHDOG_PRESC 34 /* wdog prescaler 2^(64-34) (~10min) */
+#define CONFIG_WATCHDOG_RC WRC_CHIP /* reset chip on watchdog event */
+
+
/*
* additionnal command line configuration.
*/
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
+#define CONFIG_CMD_ERRATA
/* we don't need flash support */
#define CONFIG_SYS_NO_FLASH
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_FLASH
#undef CONFIG_FLASH_CFI_MTD
#undef CONFIG_JFFS2_CMDLINE
#endif
#define __USB_PHY_TYPE utmi
+#define CONFIG_USB_EHCI_FSL
/*
* Environment Configuration
"sf probe 0;sf erase 0 +${filesize};" \
"sf write ${load_addr_r} 0 ${filesize};\0" \
"set_fdthigh=true\0" \
+ "checkfdt=true\0" \
""
#define CONFIG_HW_ENV_SETTINGS \
projects / people / ms / u-boot.git / blobdiff