]> git.ipfire.org Git - people/ms/u-boot.git/blobdiff - include/configs/ls1043ardb.h
usb: move CONFIG_USB_XHCI_DWC3 to Kconfig
[people/ms/u-boot.git] / include / configs / ls1043ardb.h
index 7d113a0737ec68ab434ddcb6079c35e13f6e097d..94ddfb1797650da0c966b643a2a35877735fa003 100644 (file)
@@ -27,7 +27,7 @@
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 /* Physical Memory Map */
 #define CONFIG_CHIP_SELECTS_PER_CTRL   4
-#define CONFIG_NR_DRAM_BANKS           1
+#define CONFIG_NR_DRAM_BANKS           2
 
 #define CONFIG_SYS_SPD_BUS_NUM         0
 
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  5
 
-/* DSPI */
-#define CONFIG_FSL_DSPI
-#ifdef CONFIG_FSL_DSPI
-#define CONFIG_CMD_SF
-#define CONFIG_DM_SPI_FLASH
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_SF_DEFAULT_BUS          1
-#define CONFIG_SF_DEFAULT_CS           0
-#endif
-
 /*
  * Environment
  */
 /* FMan */
 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_FMAN_ENET
-#define CONFIG_CMD_MII
 #define CONFIG_PHYLIB
 #define CONFIG_PHYLIB_10G
 #define CONFIG_PHY_GIGE                /* Include GbE speed/duplex detection */
 #define CONFIG_PHY_VITESSE
 #define CONFIG_PHY_REALTEK
 #define CONFIG_PHY_AQUANTIA
+#define AQR105_IRQ_MASK                        0x40000000
 
 #define RGMII_PHY1_ADDR                        0x1
 #define RGMII_PHY2_ADDR                        0x2
 #define CONFIG_ETHPRIME                        "FM1@DTSEC3"
 #endif
 
+/* QE */
+#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \
+       !defined(CONFIG_QSPI_BOOT)
+#define CONFIG_U_QE
+#endif
+#define CONFIG_SYS_QE_FW_ADDR     0x60600000
+
 /* USB */
 #define CONFIG_HAS_FSL_XHCI_USB
 #ifdef CONFIG_HAS_FSL_XHCI_USB
-#define CONFIG_USB_XHCI
 #define CONFIG_USB_XHCI_FSL
-#define CONFIG_USB_XHCI_DWC3
 #define CONFIG_USB_MAX_CONTROLLER_COUNT                3
 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS     2
-#define CONFIG_CMD_USB
 #define CONFIG_USB_STORAGE
+#endif
+
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_CMD_SCSI
+#ifndef CONFIG_CMD_FAT
+#define CONFIG_CMD_FAT
+#endif
+#ifndef CONFIG_CMD_EXT2
 #define CONFIG_CMD_EXT2
 #endif
+#define CONFIG_DOS_PARTITION
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID            2
+#define CONFIG_SYS_SCSI_MAX_LUN                        2
+#define CONFIG_SYS_SCSI_MAX_DEVICE             (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+                                               CONFIG_SYS_SCSI_MAX_LUN)
+#define SCSI_VEND_ID 0x1b4b
+#define SCSI_DEV_ID  0x9170
+#define CONFIG_SCSI_DEV_LIST {SCSI_VEND_ID, SCSI_DEV_ID}
+#define CONFIG_PCI
+
+#include <asm/fsl_secure_boot.h>
 
 #endif /* __LS1043ARDB_H__ */