#ifndef __LS1046A_COMMON_H
#define __LS1046A_COMMON_H
+/* SPL build */
+#ifdef CONFIG_SPL_BUILD
+#define SPL_NO_QBMAN
+#define SPL_NO_FMAN
+#define SPL_NO_ENV
+#define SPL_NO_MISC
+#define SPL_NO_QSPI
+#define SPL_NO_USB
+#define SPL_NO_SATA
+#endif
+#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
+#define SPL_NO_MMC
+#endif
+#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT))
+#define SPL_NO_IFC
+#endif
+
#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LAYERSCAPE
#define CONFIG_MP
-#define CONFIG_SYS_FSL_CLK
#define CONFIG_GICV2
#include <asm/arch/config.h>
+#include <asm/arch/stream_id_lsch2.h>
/* Link Definitions */
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
-#define CONFIG_SUPPORT_RAW_INITRD
-
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F 1
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+#define CONFIG_SYS_NS16550_CLK (get_serial_clock())
-#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/* SD boot SPL */
#ifdef CONFIG_SD_BOOT
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
CONFIG_SPL_BSS_MAX_SIZE)
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
-#define CONFIG_SYS_MONITOR_LEN 0xa0000
+
+#ifdef CONFIG_SECURE_BOOT
+#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
+/*
+ * HDR would be appended at end of image and copied to DDR along
+ * with U-Boot image. Here u-boot max. size is 512K. So if binary
+ * size increases then increase this size in case of secure boot as
+ * it uses raw u-boot image instead of fit image.
+ */
+#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
+#else
+#define CONFIG_SYS_MONITOR_LEN 0x100000
+#endif /* ifdef CONFIG_SECURE_BOOT */
#endif
/* NAND SPL */
#ifdef CONFIG_NAND_BOOT
#define CONFIG_SPL_PBL_PAD
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
#define CONFIG_SPL_TEXT_BASE 0x10000000
-#define CONFIG_SPL_MAX_SIZE 0x1d000 /* 116 KiB */
+#define CONFIG_SPL_MAX_SIZE 0x17000 /* 90 KiB */
#define CONFIG_SPL_STACK 0x1001f000
#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_I2C_MXC_I2C3
#define CONFIG_SYS_I2C_MXC_I2C4
+/* PCIe */
+#define CONFIG_PCIE1 /* PCIE controller 1 */
+#define CONFIG_PCIE2 /* PCIE controller 2 */
+#define CONFIG_PCIE3 /* PCIE controller 3 */
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_SCAN_SHOW
+#endif
+
+/* SATA */
+#ifndef SPL_NO_SATA
+#define CONFIG_SCSI_AHCI_PLAT
+
+#define CONFIG_SYS_SATA AHCI_BASE_ADDR
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+#endif
+
/* Command line configuration */
-#define CONFIG_CMD_ENV
/* MMC */
-#define CONFIG_MMC
+#ifndef SPL_NO_MMC
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
-#define CONFIG_GENERIC_MMC
-#define CONFIG_DOS_PARTITION
#endif
-
-#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
-
-#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#endif
/* FMan ucode */
+#ifndef SPL_NO_FMAN
#define CONFIG_SYS_DPAA_FMAN
#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_FM_MURAM_SIZE 0x60000
+#endif
#ifdef CONFIG_SD_BOOT
/*
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
* about 1MB (2048 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820).
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 18432(0x4800).
*/
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
+#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x4800)
#elif defined(CONFIG_QSPI_BOOT)
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_FMAN_FW_ADDR 0x40300000
+#define CONFIG_SYS_FMAN_FW_ADDR 0x40900000
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 1000000
#define CONFIG_ENV_SPI_MODE 0x03
#elif defined(CONFIG_NAND_BOOT)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR (36 * CONFIG_SYS_NAND_BLOCK_SIZE)
#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_FMAN_FW_ADDR 0x60300000
+#define CONFIG_SYS_FMAN_FW_ADDR 0x60900000
#endif
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
-#define CONFIG_ARCH_EARLY_INIT_R
-#define CONFIG_BOARD_LATE_INIT
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
+#ifndef CONFIG_SPL_BUILD
+#define BOOT_TARGET_DEVICES(func) \
+ func(SCSI, scsi, 0) \
+ func(MMC, mmc, 0) \
+ func(USB, usb, 0)
+#include <config_distro_bootcmd.h>
+#endif
+
+#ifndef SPL_NO_MISC
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
- "loadaddr=0x80100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xffffffffffffffff\0" \
"initrd_high=0xffffffffffffffff\0" \
+ "fdt_addr=0x64f00000\0" \
+ "kernel_addr=0x65000000\0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
+ "fdtheader_addr_r=0x80100000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "load_addr=0xa0000000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "fdt_addr_r=0x90000000\0" \
+ "ramdisk_addr_r=0xa0000000\0" \
"kernel_start=0x1000000\0" \
+ "kernelheader_start=0x800000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
+ "kernelheader_size=0x40000\0" \
+ "kernel_addr_sd=0x8000\0" \
+ "kernel_size_sd=0x14000\0" \
+ "kernelhdr_addr_sd=0x4000\0" \
+ "kernelhdr_size_sd=0x10\0" \
"console=ttyS0,115200\0" \
- MTDPARTS_DEFAULT "\0"
+ CONFIG_MTDPARTS_DEFAULT "\0" \
+ BOOTENV \
+ "boot_scripts=ls1046ardb_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1046ardb_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "scan_dev_for_boot=" \
+ "echo Scanning ${devtype} " \
+ "${devnum}:${distro_bootpart}...; " \
+ "for prefix in ${boot_prefixes}; do " \
+ "run scan_dev_for_scripts; " \
+ "done;" \
+ "\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr} " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0" \
+ "qspi_bootcmd=echo Trying load from qspi..;" \
+ "sf probe && sf read $load_addr " \
+ "$kernel_start $kernel_size; env exists secureboot " \
+ "&& sf read $kernelheader_addr_r $kernelheader_start " \
+ "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
+ "bootm $load_addr#$board\0" \
+ "sd_bootcmd=echo Trying load from SD ..;" \
+ "mmcinfo; mmc read $load_addr " \
+ "$kernel_addr_sd $kernel_size_sd && " \
+ "env exists secureboot && mmc read $kernelheader_addr_r " \
+ "$kernelhdr_addr_sd $kernelhdr_size_sd " \
+ " && esbc_validate ${kernelheader_addr_r};" \
+ "bootm $load_addr#$board\0"
+
+#endif
-#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \
- "earlycon=uart8250,mmio,0x21c0500 " \
- MTDPARTS_DEFAULT
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_AUTO_COMPLETE
+
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-/* Hash command with SHA acceleration supported in hardware */
-#ifdef CONFIG_FSL_CAAM
-#define CONFIG_CMD_HASH
-#define CONFIG_SHA_HW_ACCEL
-#endif
+#include <asm/arch/soc.h>
#endif /* __LS1046A_COMMON_H */
projects / people / ms / u-boot.git / blobdiff