#define CONFIG_LWMON5 1 /* Board is lwmon5 */
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
#define CONFIG_440 1 /* ... PPC440 family */
-#define CONFIG_4xx 1 /* ... PPC4xx family */
-#ifdef CONFIG_LCD4_LWMON5
-#define CONFIG_SYS_TEXT_BASE 0x01000000 /* SPL U-Boot TEXT_BASE */
-#define CONFIG_HOSTNAME lcd4_lwmon5
-#else
+
#define CONFIG_SYS_TEXT_BASE 0xFFF80000
#define CONFIG_HOSTNAME lwmon5
-#endif
#define CONFIG_SYS_CLK_FREQ 33300000 /* external freq to pll */
#define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE1 + 0x10000000)
#define CONFIG_SYS_PCI_MEMBASE3 (CONFIG_SYS_PCI_MEMBASE2 + 0x10000000)
-#ifndef CONFIG_LCD4_LWMON5
#define CONFIG_SYS_USB2D0_BASE 0xe0000100
#define CONFIG_SYS_USB_DEVICE 0xe0000000
#define CONFIG_SYS_USB_HOST 0xe0000400
-#endif
/*
* Initial RAM & stack pointer
* content during reset (GPT0_COMP6). This way we reserve the OCM (16k)
* for logbuffer only. (GPT0_COMP1-COMP5 are reserved for logbuffer header.)
*/
-#ifndef CONFIG_LCD4_LWMON5
#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */
#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */
#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#else
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE
-#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-#endif
+
/* unused GPT0 COMP reg */
#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
#define CONFIG_SYS_OCM_SIZE (16 << 10)
* Serial Port
*/
#define CONFIG_CONS_INDEX 2 /* Use UART1 */
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#define CONFIG_SYS_MBYTES_SDRAM 256
#define CONFIG_SYS_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
-#ifndef CONFIG_LCD4_LWMON5
#define CONFIG_DDR_ECC /* enable ECC */
-#endif
-#ifndef CONFIG_LCD4_LWMON5
/* POST support */
#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
CONFIG_SYS_POST_CPU | \
#define CONFIG_ALT_LH_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP1)
#define CONFIG_ALT_LB_ADDR (CONFIG_SYS_OCM_BASE)
#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-#endif
/*
* I2C
/*
* Pass open firmware flat tree
*/
-#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
/* Update size in "reg" property of NOR FLASH device tree nodes */
#define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_SPLASH_SCREEN
-#ifndef CONFIG_LCD4_LWMON5
/*
* USB/EHCI
*/
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
-#endif
/*
* BOOTP options
/*
* Command line configuration.
*/
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_BMP
#endif
-#ifndef CONFIG_LCD4_LWMON5
#ifdef CONFIG_440EPX
#define CONFIG_CMD_USB
#endif
-#endif
/*
* Miscellaneous configurable options
#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup*/
-#ifndef CONFIG_LCD4_LWMON5
#ifndef DEBUG
#define CONFIG_HW_WATCHDOG 1 /* Use external HW-Watchdog */
#endif
#define CONFIG_WD_PERIOD 40000 /* in usec */
#define CONFIG_WD_MAX_RATE 66600 /* in ticks */
-#endif
/*
* For booting Linux, the board info and command line data
#define CONFIG_SYS_GPIO_SYSMON_STATUS 62
#define CONFIG_SYS_GPIO_WATCHDOG 63
-/* On LCD4, GPIO49 has to be configured to 0 instead of 1 */
-#ifdef CONFIG_LCD4_LWMON5
-#define GPIO49_VAL 0
-#else
#define GPIO49_VAL 1
-#endif
/*
* PPC440 GPIO Configuration
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#endif
-/*
- * SPL related defines
- */
-#ifdef CONFIG_LCD4_LWMON5
-#define CONFIG_SPL
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SPL_NOR_SUPPORT
-#define CONFIG_SPL_TEXT_BASE 0xffff0000 /* last 64 KiB for SPL */
-#define CONFIG_SYS_SPL_MAX_LEN (64 << 10)
-#define CONFIG_UBOOT_PAD_TO 458752 /* decimal for 'dd' */
-#define CONFIG_SPL_START_S_PATH "arch/powerpc/cpu/ppc4xx"
-#define CONFIG_SPL_LDSCRIPT "arch/powerpc/cpu/ppc4xx/u-boot-spl.lds"
-#define CONFIG_SPL_LIBCOMMON_SUPPORT /* image.c */
-#define CONFIG_SPL_LIBGENERIC_SUPPORT /* string.c */
-#define CONFIG_SPL_SERIAL_SUPPORT
-
-/* Place BSS for SPL near end of SDRAM */
-#define CONFIG_SPL_BSS_START_ADDR ((256 - 1) << 20)
-#define CONFIG_SPL_BSS_MAX_SIZE (64 << 10)
-
-#define CONFIG_SPL_OS_BOOT
-/* Place patched DT blob (fdt) at this address */
-#define CONFIG_SYS_SPL_ARGS_ADDR 0x01800000
-
-#define CONFIG_SPL_TARGET "u-boot-img-spl-at-end.bin"
-
-/* Settings for real U-Boot to be loaded from NOR flash */
-#define CONFIG_SYS_UBOOT_BASE (-CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_SYS_UBOOT_START 0x01002100
-
-#define CONFIG_SYS_OS_BASE 0xf8000000
-#define CONFIG_SYS_FDT_BASE 0xf87c0000
-#endif
-
#endif /* __CONFIG_H */
projects / people / ms / u-boot.git / blobdiff