Convert CONFIG_CMD_JFFS2 to Kconfig

[people/ms/u-boot.git] / include / configs / motionpro.h

diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h
index d7383a62c69072664bc8cde3d01221e44e1ebe53..75633f66ef849345297076e83f29e99ab69178e6 100644 (file)
--- a/include/configs/motionpro.h
+++ b/include/configs/motionpro.h
@@ -4,7 +4,7 @@
  *
  * Based on Motion-PRO board config file by Robert McCullough, rob@promessinc.com
  *
- * SPDX-License-Identifier:    GPL-2.0+ 
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -15,8 +15,7 @@
  */
 
 /* CPU and board */
-#define CONFIG_MPC5xxx         1       /* This is an MPC5xxx CPU */
-#define CONFIG_MPC5200         1       /* More exactly a MPC5200 */
+#define CONFIG_MPC5200         1       /* This is a MPC5200 CPU */
 #define CONFIG_MOTIONPRO       1       /* ... on Promess Motion-PRO board */
 
 #define CONFIG_HIGH_BATS       1       /* High BATs supported */
@@ -34,23 +33,6 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 
 /*
@@ -58,7 +40,6 @@
  */
 #define CONFIG_PSC_CONSOLE     1       /* console is on PSC1 */
 #define CONFIG_NETCONSOLE      1       /* network console */
-#define CONFIG_BAUDRATE                115200
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200, 230400 }
 
 /*
@@ -73,22 +54,9 @@
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY       2       /* autoboot after 2 seconds */
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_STOP_STR       "\x1b\x1b"
-#define DEBUG_BOOTKEYS         0
-#undef CONFIG_AUTOBOOT_DELAY_STR
 #undef CONFIG_BOOTARGS
-#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds, "           \
-                               "press \"<Esc><Esc>\" to stop\n", bootdelay
 
 #define CONFIG_CMDLINE_EDITING         1       /* add command line history     */
-#define        CONFIG_SYS_HUSH_PARSER          1       /* use "hush" command parser    */
-#define        CONFIG_SYS_PROMPT_HUSH_PS2      "> "
-
-#define CONFIG_ETHADDR         00:50:C2:40:10:00
-#define CONFIG_OVERWRITE_ETHADDR_ONCE  1
-#define CONFIG_VERSION_VARIABLE        1       /* include version env variable */
 
 /*
  * Default environment settings
@@ -281,23 +249,6 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET     0x0060
 #define CONFIG_SYS_ATA_REG_OFFSET      CONFIG_SYS_ATA_DATA_OFFSET
 #define CONFIG_SYS_ATA_STRIDE          4
-#define CONFIG_DOS_PARTITION
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C                1       /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE          2       /* select I2C module #2 */
-#define CONFIG_SYS_I2C_SPEED           100000  /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE           0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      1       /* 2 bytes per write cycle */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  5       /* 2ms/cycle + 3ms extra */
-#define CONFIG_SYS_I2C_MULTI_EEPROMS           1       /* 2 EEPROMs (addr:50,52) */
 
 /*
  * RTC configuration
@@ -308,30 +259,10 @@
 /*
  * Status LED configuration
  */
-#define CONFIG_STATUS_LED              /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED
 
 #define ENABLE_GPIO_OUT                0x00000024
 #define LED_ON                 0x00000010
 
-#ifndef __ASSEMBLY__
-/*
- * In case of Motion-PRO, a LED is identified by its corresponding
- * GPT Enable and Mode Select Register.
- */
-typedef volatile unsigned long * led_id_t;
-
-extern void __led_init(led_id_t id, int state);
-extern void __led_toggle(led_id_t id);
-extern void __led_set(led_id_t id, int state);
-#endif /* __ASSEMBLY__ */
-
-/*
- * Temperature sensor
- */
-#define CONFIG_DTT_LM75                1
-#define CONFIG_DTT_SENSORS     { 0x49 }
-
 /*
  * Environment settings
  */
@@ -368,7 +299,6 @@ extern void __led_set(led_id_t id, int state);
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory    */
-#define CONFIG_SYS_PROMPT              "=> "   /* Monitor Command Prompt   */
 #define CONFIG_SYS_CBSIZE              1024    /* Console I/O Buffer Size */
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)     /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS             16              /* max number of command args */
@@ -380,8 +310,6 @@ extern void __led_set(led_id_t id, int state);
 
 #define CONFIG_SYS_LOAD_ADDR           0x200000        /* default kernel load addr */
 
-#define CONFIG_SYS_HZ                  1000    /* decrementer freq: 1 ms ticks */
-
 /*
  * Various low-level settings
  */
@@ -393,10 +321,6 @@ extern void __led_set(led_id_t id, int state);
 /* Not needed for MPC 5xxx U-Boot, but used by tools/updater */
 #define CONFIG_SYS_RESET_ADDRESS       0xfff00100
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT       1
-#define CONFIG_OF_BOARD_SETUP  1
-
 #define OF_CPU                 "PowerPC,5200@0"
 #define OF_SOC                 "soc5200@f0000000"
 #define OF_TBCLK               (bd->bi_busfreq / 4)