configs: Re-sync almost all of cmd/Kconfig

[people/ms/u-boot.git] / include / configs / mx6qsabreauto.h

diff --git a/include/configs/mx6qsabreauto.h b/include/configs/mx6qsabreauto.h
index 1583c11aab8cd0eb77e531cf1baf2e0267f336b8..6039fc4f62e58d8df5ef6824d9dde207ccc9e19a 100644 (file)
--- a/include/configs/mx6qsabreauto.h
+++ b/include/configs/mx6qsabreauto.h
@@ -3,10 +3,7 @@
  *
  * Configuration settings for the Freescale i.MX6Q SabreAuto board.
  *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 #ifndef __MX6QSABREAUTO_CONFIG_H
@@ -15,27 +12,68 @@
 #define CONFIG_MACH_TYPE       3529
 #define CONFIG_MXC_UART_BASE   UART4_BASE
 #define CONFIG_CONSOLE_DEV             "ttymxc3"
-#define CONFIG_DEFAULT_FDT_FILE        "imx6q-sabreauto.dtb"
 #define CONFIG_MMCROOT                 "/dev/mmcblk0p2"
 #define PHYS_SDRAM_SIZE                (2u * 1024 * 1024 * 1024)
 
 /* USB Configs */
-#define CONFIG_CMD_USB
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_MX6
 #define CONFIG_USB_STORAGE
 #define CONFIG_USB_HOST_ETHER
 #define CONFIG_USB_ETHER_ASIX
-#define CONFIG_MXC_USB_PORT    1
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET       /* For OTG port */
 #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_MXC_USB_FLAGS   0
 
-#include "mx6qsabre_common.h"
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_WIDTH   { {0x30, 8}, {0x32, 8}, {0x34, 8} }
+
+#include "mx6sabre_common.h"
+
+#undef CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
+#define CONFIG_SYS_FLASH_SECT_SIZE      (128 * 1024)
+#define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256   /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER         /* Use drivers/cfi_flash.c */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
+#define CONFIG_SYS_FLASH_EMPTY_INFO
 
 #define CONFIG_SYS_FSL_USDHC_NUM       2
 #if defined(CONFIG_ENV_IS_IN_MMC)
 #define CONFIG_SYS_MMC_ENV_DEV         0
-#define CONFIG_SYS_MMC_ENV_PART                1       /* Boot partition 1 */
 #endif
 
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1                /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2                /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3                /* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED           100000
+
+/* NAND flash command */
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
+
+/* NAND stuff */
+#define CONFIG_NAND_MXS
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define CONFIG_SYS_NAND_BASE           0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
+
 #endif                         /* __MX6QSABREAUTO_CONFIG_H */