#ifndef __CONFIG_H
#define __CONFIG_H
+/* High Level Configuration Options */
+
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+
/*
- * High Level Configuration Options
+ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
+ * 64 bytes before this address should be set aside for u-boot.img's
+ * header. That is 0x800FFFC0--0x80100000 should not be used for any
+ * other needs. We use this rather than the inherited defines from
+ * ti_armv7_common.h for backwards compatibility.
*/
-#define CONFIG_OMAP /* in a TI OMAP core */
-#define CONFIG_OMAP34XX /* which is a 34XX */
-#define CONFIG_OMAP3_LOGIC /* working with Logic OMAP boards */
-#define CONFIG_OMAP_GPIO
-#define CONFIG_OMAP_COMMON
+#define CONFIG_SYS_TEXT_BASE 0x80100000
+#define CONFIG_SPL_BSS_START_ADDR 0x80000000
+#define CONFIG_SPL_BSS_MAX_SIZE (512 << 10) /* 512 KB */
+#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
-#define CONFIG_SYS_TEXT_BASE 0x80400000
+#include <configs/ti_omap3_common.h>
-#define CONFIG_SDRC /* The chip has SDRC controller */
+/* Override default SPL info to minimize empty space and allow BCH8 in SPL */
+#undef CONFIG_SPL_TEXT_BASE
+#undef CONFIG_SPL_MAX_SIZE
+#define CONFIG_SPL_TEXT_BASE 0x40200000
+#define CONFIG_SPL_MAX_SIZE (64 * 1024)
-#include <asm/arch/cpu.h> /* get chip and board defs */
-#include <asm/arch/omap3.h>
+/* Display CPU and Board information */
-/*
- * Display CPU and Board information
- */
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
-/* Clock Defines */
-#define V_OSCK 26000000 /* Clock output from T2 */
-#define V_SCLK (V_OSCK >> 1)
-
#define CONFIG_MISC_INIT_R /* misc_init_r dumps the die id */
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
+#define CONFIG_CMDLINE_EDITING /* cmd line edit/history */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check keypress w/no delay */
-#define CONFIG_CMDLINE_EDITING /* cmd line edit/history */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check keypress w/no delay */
+/* Hardware drivers */
-/*
- * Size of malloc() pool
- */
-#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
- /* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
+/* GPIO banks */
+#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
-/*
- * Hardware drivers
- */
-
-/*
- * NS16550 Configuration
- */
-#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+#define CONFIG_USB_OMAP3
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
-
-/*
- * select serial console configuration
- */
+/* select serial console configuration */
+#undef CONFIG_CONS_INDEX
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
#define CONFIG_SERIAL1 1 /* UART1 on OMAP Logic boards */
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
- 115200}
-#define CONFIG_GENERIC_MMC
-#define CONFIG_MMC
-#define CONFIG_OMAP_HSMMC
-#define CONFIG_DOS_PARTITION
-
/* commands to include */
-#include <config_cmd_default.h>
-
+#define CONFIG_CMD_NAND
#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_EXT2 /* EXT2 Support */
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
-#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
-#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(x-loader),"\
- "1920k(u-boot),128k(u-boot-env),"\
- "4m(kernel),-(fs)"
-
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MMC /* MMC support */
-#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_MTDPARTS
#define CONFIG_CMD_NAND_LOCK_UNLOCK /* nand (un)lock commands */
-#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_SETEXPR /* Evaluate expressions */
-#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
-#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
-#undef CONFIG_CMD_IMI /* iminfo */
-#undef CONFIG_CMD_IMLS /* List all found images */
-
-#define CONFIG_SYS_NO_FLASH
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
-#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
+/* I2C */
#define CONFIG_SYS_I2C_OMAP34XX
-
-/*
- * TWL4030
- */
-#define CONFIG_TWL4030_POWER
-
-/*
- * Board NAND Info.
- */
-#define CONFIG_SYS_NAND_QUIET_TEST
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */
+#define EXPANSION_EEPROM_I2C_BUS 2 /* I2C Bus for AT24C64 */
+#define CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID
+
+/* USB */
+#define CONFIG_USB_MUSB_GADGET
+#define CONFIG_USB_MUSB_OMAP2PLUS
+#define CONFIG_USB_MUSB_PIO_ONLY
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETHER_RNDIS
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_VBUS_DRAW 0
+#define CONFIG_USB_GADGET_DOWNLOAD
+#define CONFIG_G_DNL_VENDOR_NUM 0x0451
+#define CONFIG_G_DNL_PRODUCT_NUM 0xd022
+#define CONFIG_G_DNL_MANUFACTURER "TI"
+#define CONFIG_USB_FUNCTION_FASTBOOT
+#define CONFIG_CMD_FASTBOOT
+#define CONFIG_ANDROID_BOOT_IMAGE
+#define CONFIG_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR
+#define CONFIG_FASTBOOT_BUF_SIZE 0x07000000
+#define CONFIG_SYS_CACHELINE_SIZE 64
+
+/* TWL4030 */
+#define CONFIG_TWL4030_PWM
+#define CONFIG_TWL4030_USB
+
+/* Board NAND Info. */
+#ifdef CONFIG_NAND
#define CONFIG_NAND_OMAP_GPMC
-#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
- /* to access nand */
-#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
- /* to access nand at */
- /* CS0 */
-
-#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
- /* NAND devices */
-#define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16
-#define CONFIG_JFFS2_NAND
-/* nand device jffs2 lives on */
-#define CONFIG_JFFS2_DEV "nand0"
-/* start of jffs2 partition */
-#define CONFIG_JFFS2_PART_OFFSET 0x680000
-#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */
- /* partition */
+
+#define CONFIG_CMD_UBI /* UBI-formated MTD partition support */
+#define CONFIG_CMD_UBIFS /* Read-only UBI volume operations */
+#define CONFIG_RBTREE /* required by CONFIG_CMD_UBI */
+#define CONFIG_LZO /* required by CONFIG_CMD_UBIFS */
+
+#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
+ /* to access nand */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
+ /* NAND devices */
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \
+ 13, 14, 16, 17, 18, 19, 20, 21, 22, \
+ 23, 24, 25, 26, 27, 28, 30, 31, 32, \
+ 33, 34, 35, 36, 37, 38, 39, 40, 41, \
+ 42, 44, 45, 46, 47, 48, 49, 50, 51, \
+ 52, 53, 54, 55, 56}
+
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 13
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
+#define CONFIG_BCH
+#define CONFIG_SYS_NAND_MAX_OOBFREE 2
+#define CONFIG_SYS_NAND_MAX_ECCPOS 56
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
+#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
+#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(MLO),"\
+ "1920k(u-boot),128k(u-boot-env),"\
+ "4m(kernel),-(fs)"
+#endif
/* Environment information */
-#define CONFIG_BOOTDELAY 2
/*
* PREBOOT assumes the 4.3" display is attached. User can interrupt
"echo \"Defaulting to 4.3 LCD panel (display=15).\";" \
"setenv display 15;" \
"setenv preboot;" \
+ "nand unlock;" \
"saveenv;"
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x81000000\0" \
- "bootfile=uImage\0" \
+ "uimage=uImage\0" \
+ "zimage=zImage\0" \
"mtdids=" MTDIDS_DEFAULT "\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
"mmcdev=0\0" \
+ "mmcroot=/dev/mmcblk0p2 rw\0" \
+ "mmcrootfstype=ext4 rootwait\0" \
+ "nandroot=ubi0:rootfs rw ubi.mtd=fs noinitrd\0" \
+ "nandrootfstype=ubifs rootwait\0" \
"autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"setenv bootargs ${bootargs} omapfb.vrfb=y " \
"omapfb.rotate=${rotation}; " \
"fi\0" \
- "otherbootargs=ignore_loglevel early_printk no_console_suspend\0" \
+ "optargs=ignore_loglevel early_printk no_console_suspend\0" \
"addmtdparts=setenv bootargs ${bootargs} ${mtdparts}\0" \
"common_bootargs=setenv bootargs ${bootargs} display=${display} " \
- "${otherbootargs};" \
+ "${optargs};" \
"run addmtdparts; " \
"run vrfb_arg\0" \
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo 'Running bootscript from mmc ...'; " \
"source ${loadaddr}\0" \
- "loaduimage=mmc rescan ${mmcdev}; " \
- "fatload mmc ${mmcdev} ${loadaddr} ${bootfile}\0" \
+ "loaduimage=mmc rescan; " \
+ "fatload mmc ${mmcdev} ${loadaddr} ${uimage}\0" \
+ "loadzimage=mmc rescan; " \
+ "fatload mmc ${mmcdev} ${loadaddr} ${zimage}\0" \
"ramdisksize=64000\0" \
"ramdiskaddr=0x82000000\0" \
"ramdiskimage=rootfs.ext2.gz.uboot\0" \
+ "loadramdisk=mmc rescan; " \
+ "fatload mmc ${mmcdev} ${ramdiskaddr} ${ramdiskimage}\0" \
"ramargs=run setconsole; setenv bootargs console=${console} " \
"root=/dev/ram rw ramdisk_size=${ramdisksize}\0" \
- "mmcramboot=echo 'Booting kernel from mmc w/ramdisk...'; " \
+ "mmcargs=run setconsole; setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=${mmcroot} " \
+ "rootfstype=${mmcrootfstype}\0" \
+ "nandargs=run setconsole; setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype}\0" \
+ "fdtaddr=0x86000000\0" \
+ "loadfdtimage=mmc rescan; " \
+ "fatload mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
+ "mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
+ "run mmcargs; " \
+ "run common_bootargs; " \
+ "run dump_bootargs; " \
+ "run loadzimage; " \
+ "run loadfdtimage; " \
+ "bootz ${loadaddr} - ${fdtaddr}\0" \
+ "mmcramboot=echo 'Booting uImage kernel from mmc w/ramdisk...'; " \
"run ramargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
"run loaduimage; " \
- "fatload mmc ${mmcdev} ${ramdiskaddr} ${ramdiskimage}; "\
+ "run loadramdisk; " \
"bootm ${loadaddr} ${ramdiskaddr}\0" \
- "ramboot=echo 'Booting kernel/ramdisk rootfs from tftp...'; " \
+ "mmcrambootz=echo 'Booting zImage kernel from mmc w/ramdisk...'; " \
+ "run ramargs; " \
+ "run common_bootargs; " \
+ "run dump_bootargs; " \
+ "run loadzimage; " \
+ "run loadramdisk; " \
+ "run loadfdtimage; " \
+ "bootz ${loadaddr} ${ramdiskaddr} ${fdtaddr}\0; " \
+ "tftpboot=echo 'Booting kernel/ramdisk rootfs from tftp...'; " \
"run ramargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
- "tftpboot ${loadaddr} ${bootfile}; "\
- "tftpboot ${ramdiskaddr} ${ramdiskimage}; "\
+ "tftpboot ${loadaddr} ${uimage}; " \
+ "tftpboot ${ramdiskaddr} ${ramdiskimage}; " \
"bootm ${loadaddr} ${ramdiskaddr}\0"
#define CONFIG_BOOTCOMMAND \
"run autoboot"
+/* Miscellaneous configurable options */
#define CONFIG_AUTO_COMPLETE
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT "OMAP Logic # "
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
-#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
- /* address */
-
-/*
- * OMAP3 has 12 GP timers, they can be driven by the system clock
- * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
- * This rate is divided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-
-/*
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-
-/*
- * FLASH and environment organization
- */
+/* FLASH and environment organization */
/* **** PISMO SUPPORT *** */
-
-/* Configure the PISMO */
-#define PISMO1_NAND_SIZE GPMC_SIZE_128M
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-
#if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
+#define CONFIG_SYS_FLASH_BASE NAND_BASE
#elif defined(CONFIG_CMD_ONENAND)
-#define CONFIG_SYS_FLASH_BASE PISMO1_ONEN_BASE
+#define CONFIG_SYS_FLASH_BASE ONENAND_MAP
#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
+#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_OMAP_GPMC
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
-#endif
-
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET
+#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
-#define CONFIG_SYS_INIT_RAM_SIZE 0x800
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-/*
- * SMSC922x Ethernet
- */
+/* SMSC922x Ethernet */
#if defined(CONFIG_CMD_NET)
-
#define CONFIG_SMC911X
-#define CONFIG_SMC911X_16_BIT
+#define CONFIG_SMC911X_32_BIT
#define CONFIG_SMC911X_BASE 0x08000000
-
#endif /* (CONFIG_CMD_NET) */
-/*
- * BOOTP fields
- */
+/* Defines for SPL */
-#define CONFIG_BOOTP_SUBNETMASK 0x00000001
-#define CONFIG_BOOTP_GATEWAY 0x00000002
-#define CONFIG_BOOTP_HOSTNAME 0x00000004
-#define CONFIG_BOOTP_BOOTPATH 0x00000010
+#define CONFIG_SPL_OMAP3_ID_NAND
+
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x240000
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
#endif /* __CONFIG_H */
projects / people / ms / u-boot.git / blobdiff