drivers/pci/Kconfig: Add PCI

[people/ms/u-boot.git] / include / configs / qemu-ppce500.h

diff --git a/include/configs/qemu-ppce500.h b/include/configs/qemu-ppce500.h
index 10e014d33c467c31908000c539f54acfa843fb19..2c9a4aa39d94fb85f35b9fd05ed0f6ebba3e0a70 100644 (file)
--- a/include/configs/qemu-ppce500.h
+++ b/include/configs/qemu-ppce500.h
@@ -24,7 +24,6 @@
 
 #define CONFIG_SYS_RAMBOOT
 
-#define CONFIG_PCI                     /* Enable PCI/PCIE */
 #define CONFIG_PCI1            1       /* PCI controller 1 */
 #define CONFIG_FSL_PCI_INIT            /* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT           /* enable 64-bit PCI resources */
@@ -49,8 +48,12 @@
 /* Physical address should be a function call */
 #ifndef __ASSEMBLY__
 extern unsigned long long get_phys_ccsrbar_addr_early(void);
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH (get_phys_ccsrbar_addr_early() >> 32)
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW get_phys_ccsrbar_addr_early()
+#else
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
 #endif
-#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 
 /* Virtual address range for PCI region maps */
 #define CONFIG_SYS_PCI_MAP_START       0x80000000
@@ -97,7 +100,6 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 #define CONFIG_SYS_MALLOC_LEN          (4 * 1024 * 1024)
 
 #define CONFIG_CONS_INDEX      1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         (get_bus_freq(0))
@@ -108,19 +110,6 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
-
 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
@@ -128,9 +117,7 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play */
-#define CONFIG_E1000
 
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
 #define CONFIG_DOS_PARTITION
@@ -138,7 +125,6 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 
 #define CONFIG_LBA48
 #define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
 
 /*
  * Environment
@@ -152,19 +138,10 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_GREPENV
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SETEXPR
 
 #ifdef CONFIG_PCI
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
 #endif
 
 /*
@@ -199,7 +176,6 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 
 #define CONFIG_BAUDRATE        115200
 
-#define CONFIG_BOOTDELAY        1
 #define CONFIG_BOOTCOMMAND             \
        "test -n \"$qemu_kernel_addr\" && bootm $qemu_kernel_addr - $fdt_addr_r\0"