Kconfig: Move CONFIG_FIT and related options to Kconfig

[people/ms/u-boot.git] / include / configs / rpi-common.h

diff --git a/include/configs/rpi-common.h b/include/configs/rpi-common.h
index 8830a10efb012755ae76e644212a20482b89c434..7250e37a351724618112d36f3c1674b92563e4a4 100644 (file)
--- a/include/configs/rpi-common.h
+++ b/include/configs/rpi-common.h
@@ -11,7 +11,6 @@
 #include <asm/arch/timer.h>
 
 /* Architecture, CPU, etc.*/
-#define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_BCM2835
 #define CONFIG_ARCH_CPU_INIT
 
@@ -69,6 +68,7 @@
 #define CONFIG_FB_ADDR                 0
 #define CONFIG_VIDEO_BCM2835
 #define CONFIG_SYS_WHITE_ON_BLACK
+#define CONFIG_CONSOLE_SCROLL_LINES    10
 
 /* SD/MMC configuration */
 #define CONFIG_GENERIC_MMC
@@ -89,6 +89,9 @@
 #define CONFIG_USB_HOST_ETHER
 #define CONFIG_USB_ETHER_SMSC95XX
 #define CONFIG_MISC_INIT_R
+#define CONFIG_USB_KEYBOARD
+#define CONFIG_SYS_USB_EVENT_POLL
+#define CONFIG_SYS_STDIO_DEREGISTER
 #endif
 
 /* Console UART */
@@ -112,19 +115,17 @@
 #define CONFIG_SYS_LOAD_ADDR           0x1000000
 #define CONFIG_CONSOLE_MUX
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_PREBOOT                 "usb start"
 
 /* Shell */
-#define CONFIG_SYS_MAXARGS             8
+#define CONFIG_SYS_MAXARGS             16
 #define CONFIG_COMMAND_HISTORY
 
 /* Commands */
-#define CONFIG_CMD_GPIO
 #define CONFIG_CMD_MMC
 #define CONFIG_PARTITION_UUIDS
 #define CONFIG_CMD_PART
 
-/* Device tree support */
-#define CONFIG_OF_BOARD_SETUP
 /* ATAGs support for bootm/bootz */
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_CMDLINE_TAG
@@ -133,16 +134,23 @@
 #include <config_distro_defaults.h>
 
 /* Environment */
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
 #define ENV_DEVICE_SETTINGS \
-       "stdin=serial,lcd\0" \
+       "stdin=serial,usbkbd\0" \
        "stdout=serial,lcd\0" \
        "stderr=serial,lcd\0"
 
 /*
  * Memory layout for where various images get loaded by boot scripts:
  *
- * scriptaddr can be pretty much anywhere that doesn't conflict with something
- *   else. Put it low in memory to avoid conflicts.
+ * I suspect address 0 is used as the SMP pen on the RPi2, so avoid this.
+ *
+ * fdt_addr_r simply shouldn't overlap anything else. However, the RPi's
+ *   binary firmware loads a DT to address 0x100, so we choose this address to
+ *   match it. This allows custom boot scripts to pass this DT on to Linux
+ *   simply by not over-writing the data at this address. When using U-Boot,
+ *   U-Boot (and scripts it executes) typicaly ignore the DT loaded by the FW
+ *   and loads its own DT from disk (triggered by boot.scr or extlinux.conf).
  *
  * pxefile_addr_r can be pretty much anywhere that doesn't conflict with
  *   something else. Put it low in memory to avoid conflicts.
@@ -156,17 +164,19 @@
  *   this up to 16M allows for a sizable kernel to be decompressed below the
  *   compressed load address.
  *
- * fdt_addr_r simply shouldn't overlap anything else. Choosing 32M allows for
- *   the compressed kernel to be up to 16M too.
+ * scriptaddr can be pretty much anywhere that doesn't conflict with something
+ *   else. Choosing 32M allows for the compressed kernel to be up to 16M.
  *
  * ramdisk_addr_r simply shouldn't overlap anything else. Choosing 33M allows
- *   for the FDT/DTB to be up to 1M, which is hopefully plenty.
+ *   for any boot script to be up to 1M, which is hopefully plenty.
  */
 #define ENV_MEM_LAYOUT_SETTINGS \
-       "scriptaddr=0x00000000\0" \
+       "fdt_high=ffffffff\0" \
+       "initrd_high=ffffffff\0" \
+       "fdt_addr_r=0x00000100\0" \
        "pxefile_addr_r=0x00100000\0" \
        "kernel_addr_r=0x01000000\0" \
-       "fdt_addr_r=0x02000000\0" \
+       "scriptaddr=0x02000000\0" \
        "ramdisk_addr_r=0x02100000\0" \
 
 #define BOOT_TARGET_DEVICES(func) \