drivers/pci/Kconfig: Add PCI

[people/ms/u-boot.git] / include / configs / sbc8641d.h

diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
index f88d685db29784dc06c541604ddd41331dc6e9fa..ffc76f059ab8150f3a4854797489b8a16bd073b8 100644 (file)
--- a/include/configs/sbc8641d.h
+++ b/include/configs/sbc8641d.h
@@ -20,7 +20,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-
 /* High Level Configuration Options */
 #define CONFIG_MPC8641         1       /* MPC8641 specific */
 #define CONFIG_SBC8641D                1       /* SBC8641D board specific */
@@ -44,9 +43,8 @@
 #define CONFIG_SYS_SRIO
 #define CONFIG_SRIO1                   /* SRIO port 1 */
 
-#define CONFIG_PCI             1       /* Enable PCIE */
-#define CONFIG_PCIE1           1       /* PCIE controler 1 (slot 1) */
-#define CONFIG_PCIE2           1       /* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE1           1       /* PCIE controller 1 (slot 1) */
+#define CONFIG_PCIE2           1       /* PCIE controller 2 (slot 2) */
 #define CONFIG_FSL_PCI_INIT    1       /* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE 1   /* indirect PCI bridge support */
 #define CONFIG_FSL_LAW         1       /* Use common FSL init code */
@@ -67,7 +65,6 @@
 #define BANK_INTERLEAVING              0x22000000
 #define SUPER_BANK_INTERLEAVING                0x23000000
 
-
 #define CONFIG_ALTIVEC          1
 
 /*
@@ -173,7 +170,6 @@
     #define CONFIG_SYS_DDR2_CLK_CTRL   0x03800000
     #define CONFIG_SYS_DDR2_CFG_1B     0xC3008008
 
-
 #endif
 
 /* #define CONFIG_ID_EEPROM    1
@@ -257,18 +253,6 @@
 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/*
- * Pass open firmware flat tree to kernel
- */
-#define CONFIG_OF_LIBFDT               1
-#define CONFIG_OF_BOARD_SETUP          1
-#define CONFIG_OF_STDOUT_VIA_ALIAS     1
-
 /*
  * I2C
  */
@@ -312,8 +296,6 @@
 
 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 
-#undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE
-
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
@@ -479,8 +461,6 @@
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
 
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
@@ -546,7 +526,6 @@
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR                1000000
 
-#define CONFIG_BOOTDELAY 10    /* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS                /* the boot command will set bootargs */
 
 #define CONFIG_BAUDRATE        115200