#define CONFIG_SYS_TEXT_BASE 0xFE000000
-#ifdef CONFIG_STRIDER_CPU
-#define CONFIG_IDENT_STRING " strider cpu 0.01"
-#else
-#define CONFIG_IDENT_STRING " strider con 0.01"
-#endif
-
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_LAST_STAGE_INIT
-/* new uImage format support */
-#define CONFIG_FIT 1
-#define CONFIG_FIT_VERBOSE 1
-
#define CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
-#define CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_MEMTEST
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_CMD_FPGAD
/*
* FLASH on the Local Bus
*/
-#if 1
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_FLASH_CFI_LEGACY
#define CONFIG_SYS_FLASH_LEGACY_512Kx16
-#else
-#define CONFIG_SYS_NO_FLASH
-#endif
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */
| BR_PS_16 /* 16 bit port */ \
| BR_MS_GPCM /* MSEL = GPCM */ \
| BR_V) /* valid */
-#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
+
+#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
| OR_UPM_XAM \
| OR_GPCM_CSNT \
- | OR_GPCM_ACS_DIV2 \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET)
+ | OR_GPCM_SCY_5 \
+ | OR_GPCM_TRLX_CLEAR \
+ | OR_GPCM_EHTR_CLEAR)
#define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE
#define CONFIG_SYS_FPGA_DONE(k) 0x0010
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
/* Pass open firmware flat tree */
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_PCA953X /* NXP PCA9554 */
+#define CONFIG_CMD_PCA953X
+#define CONFIG_CMD_PCA953X_INFO
+#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x24, 16}, {0x25, 16}, {0x26, 16}, \
+ {0x3c, 8}, {0x3d, 8}, {0x3e, 8} }
+
#define CONFIG_PCA9698 /* NXP PCA9698 */
#define CONFIG_SYS_I2C_IHS
#define CONFIG_SYS_I2C_IHS_SPEED_3 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F
+#ifdef CONFIG_STRIDER_CON_DP
+#define CONFIG_SYS_I2C_IHS_DUAL
+#define CONFIG_SYS_I2C_IHS_CH0_1
+#define CONFIG_SYS_I2C_IHS_SPEED_0_1 50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_0_1 0x7F
+#define CONFIG_SYS_I2C_IHS_CH1_1
+#define CONFIG_SYS_I2C_IHS_SPEED_1_1 50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_1_1 0x7F
+#define CONFIG_SYS_I2C_IHS_CH2_1
+#define CONFIG_SYS_I2C_IHS_SPEED_2_1 50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_2_1 0x7F
+#define CONFIG_SYS_I2C_IHS_CH3_1
+#define CONFIG_SYS_I2C_IHS_SPEED_3_1 50000
+#define CONFIG_SYS_I2C_IHS_SLAVE_3_1 0x7F
+#endif
+
/*
* Software (bit-bang) I2C driver configuration
*/
#define I2C_SOFT_DECLARATIONS4
#define CONFIG_SYS_I2C_SOFT_SPEED_4 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F
-#ifdef CONFIG_STRIDER_CON
+#if defined(CONFIG_STRIDER_CON) || defined(CONFIG_STRIDER_CON_DP)
#define I2C_SOFT_DECLARATIONS5
#define CONFIG_SYS_I2C_SOFT_SPEED_5 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_5 0x7F
#define CONFIG_SYS_I2C_SOFT_SPEED_8 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_8 0x7F
#endif
+#ifdef CONFIG_STRIDER_CON_DP
+#define I2C_SOFT_DECLARATIONS9
+#define CONFIG_SYS_I2C_SOFT_SPEED_9 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_9 0x7F
+#define I2C_SOFT_DECLARATIONS10
+#define CONFIG_SYS_I2C_SOFT_SPEED_10 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_10 0x7F
+#define I2C_SOFT_DECLARATIONS11
+#define CONFIG_SYS_I2C_SOFT_SPEED_11 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_11 0x7F
+#define I2C_SOFT_DECLARATIONS12
+#define CONFIG_SYS_I2C_SOFT_SPEED_12 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE_12 0x7F
+#endif
#ifdef CONFIG_STRIDER_CON
#define CONFIG_SYS_ICS8N3QV01_I2C {5, 6, 7, 8}
#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4}
#define CONFIG_STRIDER_FANS { {10, 0x4c}, {11, 0x4c}, \
{12, 0x4c} }
+#elif defined(CONFIG_STRIDER_CON_DP)
+#define CONFIG_SYS_ICS8N3QV01_I2C {13, 14, 15, 16, 17, 18, 19, 20}
+#define CONFIG_SYS_CH7301_I2C {1, 3, 5, 7}
+#define CONFIG_SYS_ADV7611_I2C {1, 3, 5, 7}
+#define CONFIG_SYS_DP501_I2C {1, 3, 5, 7, 2, 4, 6, 8}
+#define CONFIG_STRIDER_FANS { {10, 0x4c}, {11, 0x4c}, \
+ {12, 0x4c} }
+#elif defined(CONFIG_STRIDER_CPU_DP)
+#define CONFIG_SYS_CH7301_I2C {1, 2, 3, 4}
+#define CONFIG_SYS_ADV7611_I2C {1, 2, 3, 4}
+#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4}
+#define CONFIG_STRIDER_FANS { {6, 0x4c}, {7, 0x4c}, \
+ {8, 0x4c} }
#else
#define CONFIG_SYS_CH7301_I2C {1, 2, 3, 4}
#define CONFIG_SYS_ADV7611_I2C {1, 2, 3, 4}
void fpga_gpio_set(unsigned int bus, int pin);
void fpga_gpio_clear(unsigned int bus, int pin);
int fpga_gpio_get(unsigned int bus, int pin);
+void fpga_control_set(unsigned int bus, int pin);
+void fpga_control_clear(unsigned int bus, int pin);
#endif
#ifdef CONFIG_STRIDER_CON
#define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0100 : 0x0020)
#define I2C_FPGA_IDX ((I2C_ADAP_HWNR > 3) ? \
(I2C_ADAP_HWNR - 4) : I2C_ADAP_HWNR)
+#elif defined(CONFIG_STRIDER_CON_DP)
+#define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200)
+#define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100)
+#define I2C_FPGA_IDX (I2C_ADAP_HWNR % 4)
#else
#define I2C_SDA_GPIO 0x0040
#define I2C_SCL_GPIO 0x0020
#define I2C_FPGA_IDX I2C_ADAP_HWNR
#endif
+
+#ifdef CONFIG_STRIDER_CON_DP
+#define I2C_ACTIVE \
+ do { \
+ if (I2C_ADAP_HWNR > 7) \
+ fpga_control_set(I2C_FPGA_IDX, 0x0004); \
+ else \
+ fpga_control_clear(I2C_FPGA_IDX, 0x0004); \
+ } while (0)
+#else
#define I2C_ACTIVE { }
+#endif
+
#define I2C_TRISTATE { }
#define I2C_READ \
(fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0)
#define CONFIG_SYS_DP501_DIFFERENTIAL
#define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */
+#ifdef CONFIG_STRIDER_CON_DP
+#define CONFIG_SYS_OSD_DH
+#endif
+
/*
* General PCI
* Addresses are mapped 1-1.
/* enable PCIE clock */
#define CONFIG_SYS_SCCR_PCIEXP1CM 1
-#define CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCIE
/*
* Command line configuration.
*/
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
-#undef CONFIG_ZERO_BOOTDELAY_CHECK /* ignore keypress on bootdelay==0 */
-
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_CONSOLE_INFO_QUIET
-
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
#define CONFIG_HOSTNAME hrcon
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
-
#endif /* __CONFIG_H */
projects / people / ms / u-boot.git / blobdiff