config: Move CONFIG_BOARD_LATE_INIT to defconfigs

[people/ms/u-boot.git] / include / configs / tqma6.h

diff --git a/include/configs/tqma6.h b/include/configs/tqma6.h
index 295e16303ca23ec61c4a9a3f2ff8b73204c8ab4e..a35d292f164365785e8ad3f9d0bbd55d95cffd0f 100644 (file)
--- a/include/configs/tqma6.h
+++ b/include/configs/tqma6.h
@@ -12,12 +12,6 @@
 #include <linux/kconfig.h>
 /* SPL */
 /* #if defined(CONFIG_SPL_BUILD) */
-
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SPL_SPI_SUPPORT
-#define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_EXT_SUPPORT
-
 /* common IMX6 SPL configuration */
 #include "imx6_spl.h"
 
@@ -39,27 +33,22 @@
 #endif
 
 #define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOARD_LATE_INIT
 
 #define CONFIG_MXC_UART
 
 /* SPI */
-#define CONFIG_CMD_SPI
 #define CONFIG_MXC_SPI
 
 /* SPI Flash */
-#define CONFIG_SPI_FLASH_STMICRO
 
 #define TQMA6_SPI_FLASH_SECTOR_SIZE    SZ_64K
 
-#define CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_BUS  0
 #define CONFIG_SF_DEFAULT_CS   0
 #define CONFIG_SF_DEFAULT_SPEED        50000000
 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
 
 /* I2C Configs */
-#define CONFIG_CMD_I2C
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_MXC_I2C1                /* enable I2C bus 1 */
@@ -92,20 +81,14 @@
 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
 
 /* USB Configs */
-#define CONFIG_CMD_USB
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_MX6
-#define CONFIG_USB_STORAGE
 #define CONFIG_USB_HOST_ETHER
 #define CONFIG_USB_ETHER_SMSC95XX
 #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_USB_MAX_CONTROLLER_COUNT        2
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET       /* For OTG port */
 
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_MII
-
 #define CONFIG_FEC_MXC
 #define IMX_FEC_BASE                   ENET_BASE_ADDR
 #define CONFIG_PHYLIB
@@ -288,7 +271,6 @@
                "sf read ${${fdt_addr}} ${offset} ${size}; "                   \
                "setenv size ; setenv offset\0"                                \
 
-
 #define CONFIG_BOOTCOMMAND                                                     \
        "sf probe; run mmcboot; run netboot; run panicboot"                    \
 
@@ -312,7 +294,7 @@
        "uboot=u-boot.imx\0"                                                   \
        "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0"                               \
        "fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0"                          \
-       "console=" CONFIG_CONSOLE_DEV "\0"                                     \
+       "console=" CONSOLE_DEV "\0"                                     \
        "fdt_high=0xffffffff\0"                                                \
        "initrd_high=0xffffffff\0"                                             \
        "addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0"  \
@@ -379,11 +361,6 @@
 #define CONFIG_SYS_INIT_SP_ADDR \
        (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE
-
 /*
  * All the defines above are for the TQMa6 SoM
  *