Convert CONFIG_CMD_JFFS2 to Kconfig

[people/ms/u-boot.git] / include / configs / v38b.h

diff --git a/include/configs/v38b.h b/include/configs/v38b.h
index 24f951bc348838f72385c1833829673fbb37496b..c5c78bf54ce12d7d9c7a703b739c2f8db8f8017e 100644 (file)
--- a/include/configs/v38b.h
+++ b/include/configs/v38b.h
@@ -27,7 +27,6 @@
 #define CONFIG_NETCONSOLE              1
 
 #define CONFIG_BOARD_EARLY_INIT_R      1       /* do board-specific init */
-#define CONFIG_BOARD_EARLY_INIT_F      1       /* do board-specific init */
 #define CONFIG_MISC_INIT_R
 
 #define CONFIG_SYS_XLB_PIPELINING              1       /* gives better performance */
@@ -38,7 +37,6 @@
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE     1       /* console is on PSC1 */
-#define CONFIG_BAUDRATE                115200  /* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200, 230400 }
 
 /*
@@ -56,13 +54,6 @@
 /*
  * PCI - no support
  */
-#undef CONFIG_PCI
-
-/*
- * Partitions
- */
-#define CONFIG_MAC_PARTITION   1
-#define CONFIG_DOS_PARTITION   1
 
 /*
  * USB
@@ -82,12 +73,8 @@
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_DIAG
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_DATE
 
 #define CONFIG_TIMESTAMP               /* Print image info with timestamp */
 
@@ -145,27 +132,6 @@
  */
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK                 /* define for 133MHz speed */
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C                1       /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE          2       /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED           100000  /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE           0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR             0x50    /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  70
-
-/*
- * RTC configuration
- */
-#define CONFIG_SYS_I2C_RTC_ADDR                0x51
-
 /*
  * Flash configuration - use CFI driver
  */
@@ -292,8 +258,6 @@
 /*
  * Status LED
  */
-#define  CONFIG_STATUS_LED             /* Status LED enabled */
-#define  CONFIG_BOARD_SPECIFIC_LED     /* version has board specific leds */
 
 #define CONFIG_SYS_LED_BASE    MPC5XXX_GPT7_ENABLE     /* Timer 7 GPIO */
 #ifndef __ASSEMBLY__