cmd: add Kconfig option for 'date' command

[people/ms/u-boot.git] / include / configs / vme8349.h

diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h
index 7ecbafe2e582276c1787c8a96307e449811bc3b4..ae18bd6338883492540d3371795c806e4c359967 100644 (file)
--- a/include/configs/vme8349.h
+++ b/include/configs/vme8349.h
@@ -29,7 +29,6 @@
  * High Level Configuration Options
  */
 #define CONFIG_E300            1       /* E300 Family */
-#define CONFIG_MPC83xx         1       /* MPC83xx family */
 #define CONFIG_MPC834x         1       /* MPC834x family */
 #define CONFIG_MPC8349         1       /* MPC8349 specific */
 #define CONFIG_VME8349         1       /* ESD VME8349 board specific */
@@ -38,7 +37,6 @@
 
 #define CONFIG_MISC_INIT_R
 
-#define CONFIG_PCI
 /* Don't enable PCI2 on vme834x - it doesn't exist physically. */
 #undef CONFIG_MPC83XX_PCI2             /* support for 2nd PCI controller */
 
@@ -199,7 +197,6 @@
  * Serial Port
  */
 #define CONFIG_CONS_INDEX      1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -212,13 +209,6 @@
 
 #define CONFIG_CMDLINE_EDITING         /* add command line history     */
 #define CONFIG_AUTO_COMPLETE           /* add autocompletion support */
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
 
 /* I2C */
 #define CONFIG_SYS_I2C
@@ -276,7 +266,6 @@
 
 #ifndef VME_CADDY2
 #endif
-#define CONFIG_PCI_PNP         /* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
@@ -296,7 +285,6 @@
  * TSEC configuration
  */
 #ifdef VME_CADDY2
-#define CONFIG_E1000
 #else
 #define CONFIG_TSEC_ENET               /* TSEC ethernet support */
 #endif
@@ -335,7 +323,6 @@
 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
 
 #else
-       #define CONFIG_SYS_NO_FLASH             /* Flash is not usable now */
        #define CONFIG_ENV_IS_NOWHERE           /* Store ENV in memory only */
        #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
        #define CONFIG_ENV_SIZE         0x2000
@@ -355,12 +342,6 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DATE
 #define CONFIG_SYS_RTC_BUS_NUM  0x01
 #define CONFIG_SYS_I2C_RTC_ADDR        0x32
 #define CONFIG_RTC_RX8025
@@ -372,10 +353,8 @@
 
 #if defined(CONFIG_SYS_RAMBOOT)
     #undef CONFIG_CMD_ENV
-    #undef CONFIG_CMD_LOADS
 #endif
 
-#define CONFIG_CMD_ELF
 /* Pass Ethernet MAC to VxWorks */
 #define CONFIG_SYS_VXWORKS_MAC_PTR     0x000043f0
 
@@ -557,11 +536,8 @@
 
 #define CONFIG_LOADADDR                800000  /* def location for tftp and bootm */
 
-#define CONFIG_BOOTDELAY       6       /* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS                        /* boot command will set bootargs */
 
-#define CONFIG_BAUDRATE         9600
-
 #define        CONFIG_EXTRA_ENV_SETTINGS                                       \
        "netdev=eth0\0"                                                 \
        "hostname=vme8349\0"                                            \