#ifndef __CONFIG_H
#define __CONFIG_H
+#include <config_distro_defaults.h>
#include "mx6_common.h"
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_MMC_SUPPORT
#include "imx6_spl.h"
#define MACH_TYPE_WANDBOARD 4412
#define CONFIG_MACH_TYPE MACH_TYPE_WANDBOARD
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOARD_LATE_INIT
-#define CONFIG_MXC_GPIO
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART1_BASE
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
+/* SATA Configs */
-/* Command definition */
+#define CONFIG_CMD_SATA
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_DWC_AHSATA
+#define CONFIG_SYS_SATA_MAX_DEVICE 1
+#define CONFIG_DWC_AHSATA_PORT_ID 0
+#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
+#define CONFIG_LBA48
+#define CONFIG_LIBATA
+#endif
+/* Command definition */
#define CONFIG_CMD_BMODE
-#define CONFIG_CMD_SETEXPR
-
-#define CONFIG_BOOTDELAY 5
#define CONFIG_SYS_MEMTEST_START 0x10000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
-#define CONFIG_LOADADDR 0x12000000
-#define CONFIG_SYS_TEXT_BASE 0x17800000
/* I2C Configs */
-#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED 100000
/* MMC Configuration */
-#define CONFIG_FSL_ESDHC
-#define CONFIG_FSL_USDHC
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_MMC
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_BOUNCE_BUFFER
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-
/* USB Configs */
-#define CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX6
-#define CONFIG_USB_STORAGE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
/* Ethernet Configuration */
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_PHY_ATHEROS
/* Framebuffer */
-#define CONFIG_VIDEO
+#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_IPUV3
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_CMD_HDMIDETECT
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP
-
-#define CONFIG_CMD_FUSE
-#ifdef CONFIG_CMD_FUSE
-#define CONFIG_MXC_OCOTP
#endif
#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
#define CONFIG_EXTRA_ENV_SETTINGS \
- "script=boot.scr\0" \
- "image=zImage\0" \
- "console=ttymxc0\0" \
+ "console=ttymxc0,115200\0" \
"splashpos=m,m\0" \
"fdtfile=undefined\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
+ "fdt_addr_r=0x18000000\0" \
"fdt_addr=0x18000000\0" \
- "boot_fdt=try\0" \
"ip_dyn=yes\0" \
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
- "mmcpart=1\0" \
- "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
"update_sd_firmware_filename=u-boot.imx\0" \
"update_sd_firmware=" \
"if test ${ip_dyn} = yes; then " \
"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
"fi; " \
"fi\0" \
- "mmcargs=setenv bootargs console=${console},${baudrate} " \
- "root=${mmcroot}; run videoargs\0" \
- "videoargs=" \
- "setenv nextcon 0; " \
- "if hdmidet; then " \
- "setenv bootargs ${bootargs} " \
- "video=mxcfb${nextcon}:dev=hdmi,1280x720M@60," \
- "if=RGB24; " \
- "setenv fbmen fbmem=28M; " \
- "setexpr nextcon ${nextcon} + 1; " \
- "else " \
- "echo - no HDMI monitor;" \
- "fi; " \
- "i2c dev 1; " \
- "if i2c probe 0x10; then " \
- "setenv bootargs ${bootargs} " \
- "video=mxcfb${nextcon}:dev=lcd,800x480@60," \
- "if=RGB666,bpp=32; " \
- "if test 0 -eq ${nextcon}; then " \
- "setenv fbmem fbmem=10M; " \
- "else " \
- "setenv fbmem ${fbmem},10M; " \
- "fi; " \
- "setexpr nextcon ${nextcon} + 1; " \
- "else " \
- "echo '- no FWBADAPT-7WVGA-LCD-F07A-0102 display';" \
- "fi; " \
- "setenv bootargs ${bootargs} ${fbmem}\0" \
- "loadbootscript=" \
- "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source\0" \
- "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
- "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdtfile}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootz ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0" \
- "netargs=setenv bootargs console=${console},${baudrate} " \
- "root=/dev/nfs " \
- "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
- "netboot=echo Booting from net ...; " \
- "run netargs; " \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "${get_cmd} ${image}; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if ${get_cmd} ${fdt_addr} ${fdtfile}; then " \
- "bootz ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0" \
"findfdt="\
- "if test $board_rev = MX6Q ; then " \
+ "if test $board_name = C1 && test $board_rev = MX6Q ; then " \
"setenv fdtfile imx6q-wandboard.dtb; fi; " \
- "if test $board_rev = MX6DL ; then " \
+ "if test $board_name = C1 && test $board_rev = MX6DL ; then " \
"setenv fdtfile imx6dl-wandboard.dtb; fi; " \
+ "if test $board_name = B1 && test $board_rev = MX6Q ; then " \
+ "setenv fdtfile imx6q-wandboard-revb1.dtb; fi; " \
+ "if test $board_name = B1 && test $board_rev = MX6DL ; then " \
+ "setenv fdtfile imx6dl-wandboard-revb1.dtb; fi; " \
"if test $fdtfile = undefined; then " \
"echo WARNING: Could not determine dtb to use; fi; \0" \
+ "kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
+ "pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
+ "ramdisk_addr_r=0x13000000\0" \
+ "ramdiskaddr=0x13000000\0" \
+ "scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
+ BOOTENV
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(MMC, mmc, 1) \
+ func(USB, usb, 0) \
+ func(PXE, pxe, na) \
+ func(DHCP, dhcp, na)
#define CONFIG_BOOTCOMMAND \
"run findfdt; " \
- "mmc dev ${mmcdev}; if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadimage; then " \
- "run mmcboot; " \
- "else run netboot; " \
- "fi; " \
- "fi; " \
- "else run netboot; fi"
+ "run distro_bootcmd"
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-
-#define CONFIG_CMDLINE_EDITING
+#include <config_distro_bootcmd.h>
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_ENV_SIZE (8 * 1024)
#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
+#define CONFIG_ENV_OFFSET (768 * 1024)
#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_OF_LIBFDT
-#define CONFIG_CMD_BOOTZ
-
-#ifndef CONFIG_SYS_DCACHE_OFF
-#define CONFIG_CMD_CACHE
-#endif
-
#endif /* __CONFIG_H * */
projects / people / ms / u-boot.git / blobdiff