* (C) Copyright 2009
* Vipin Kumar, STMicroelectronics, <vipin.kumar@st.com>
*
- * Copyright (C) 2012 Stefan Roese <sr@denx.de>
+ * Copyright (C) 2012, 2015 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
*/
#define CONFIG_SPEAR600 /* SPEAr600 SoC */
#define CONFIG_X600 /* on X600 board */
-#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_SYS_THUMB_BUILD
#include <asm/arch/hardware.h>
#define CONFIG_SYS_SPL_LEN CONFIG_SPL_PAD_TO
#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + \
CONFIG_SYS_SPL_LEN)
+#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN 0x60000
#define CONFIG_MTD_ECC_SOFT
#define CONFIG_SYS_FSMC_NAND_8BIT
#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_NAND_ECC_BCH
+#define CONFIG_BCH
/* UBI/UBI config options */
#define CONFIG_MTD_DEVICE
/* Ethernet config options */
#define CONFIG_MII
-#define CONFIG_NET_MULTI
-#define CONFIG_PHYLIB
#define CONFIG_PHY_RESET_DELAY 10000 /* in usec */
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#define CONFIG_PHY_MICREL
+#define CONFIG_PHY_MICREL_KSZ9031
#define CONFIG_SPEAR_GPIO
/* I2C config options */
#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_DW
#define CONFIG_SYS_I2C_BASE 0xD0200000
#define CONFIG_SYS_I2C_SPEED 400000
#define CONFIG_SYS_I2C_SLAVE 0x02
#define CONFIG_FPGA_SPARTAN3
#define CONFIG_FPGA_COUNT 1
+/* USB EHCI options */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_SPEAR
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+
/*
* Command support defines
*/
-#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ENV
-#define CONFIG_CMD_FPGA
#define CONFIG_CMD_FPGA_LOADMK
-#define CONFIG_CMD_GPIO
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_MII
#define CONFIG_CMD_MTDPARTS
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_RUN
#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_LZO
-/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <config_cmd_default.h>
-
-#define CONFIG_BOOTDELAY 3
+/* Filesystem support (for USB key) */
+#define CONFIG_SUPPORT_VFAT
+#define CONFIG_DOS_PARTITION
-#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
/*
* U-Boot Environment placing definitions.
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_BOOT_PARAMS_ADDR 0x00000100
#define CONFIG_CMDLINE_TAG
-#define CONFIG_OF_LIBFDT /* enable passing of devicetree */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_MISC_INIT_R
#define CONFIG_BOARD_LATE_INIT
-#define CONFIG_LOOPW /* enable loopw command */
#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_STOP_STR " "
-#define CONFIG_AUTOBOOT_PROMPT \
- "Hit SPACE in %d seconds to stop autoboot.\n", bootdelay
#define CONFIG_SYS_MEMTEST_START 0x00800000
#define CONFIG_SYS_MEMTEST_END 0x04000000
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
-#define CONFIG_IDENT_STRING "-SPEAr"
+#define CONFIG_SYS_MALLOC_LEN (8 << 20)
#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_PROMPT "X600> "
#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
/* Use last 2 lwords in internal SRAM for bootcounter */
#define CONFIG_BOOTCOUNT_LIMIT
-#define CONFIG_SYS_BOOTCOUNT_ADDR 0xd2801ff8
+#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SRAM_BASE + \
+ CONFIG_SRAM_SIZE)
#define CONFIG_HOSTNAME x600
#define CONFIG_UBI_PART ubi0
"bootcmd=run nand_ubifs\0" \
"\0"
-/* Stack sizes */
-#define CONFIG_STACKSIZE (512 * 1024)
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x00000000
#define PHYS_SDRAM_1_MAXSIZE 0x40000000
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xD2800000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000
+#define CONFIG_SRAM_BASE 0xd2800000
+/* Preserve the last 2 lwords for the boot-counter */
+#define CONFIG_SRAM_SIZE ((8 << 10) - 0x8)
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SRAM_BASE
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
* SPL related defines
*/
-#define CONFIG_SPL_TEXT_BASE 0xd2800b00
+#define CONFIG_SPL_TEXT_BASE 0xd2800b00
+#define CONFIG_SPL_MAX_SIZE (CONFIG_SRAM_SIZE - 0xb00)
#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/spear"
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds"
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT /* image.c */
-#define CONFIG_SPL_LIBGENERIC_SUPPORT /* string.c */
-#define CONFIG_SPL_NO_PRINTF
+#define CONFIG_SPL_FRAMEWORK
/*
* Please select/define only one of the following
projects / people / ms / u-boot.git / blobdiff