cmd: add Kconfig option for 'date' command

[people/ms/u-boot.git] / include / configs / xpedite537x.h

diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h
index 988a2e8bfeb4e85b4e953159a55d74f5d64acf78..48f07b08c02e6fd568205e32ad8b9bcc14eab8cf 100644 (file)
--- a/include/configs/xpedite537x.h
+++ b/include/configs/xpedite537x.h
@@ -14,31 +14,21 @@
 /*
  * High Level Configuration Options
  */
-#define CONFIG_BOOKE           1       /* BOOKE */
-#define CONFIG_E500            1       /* BOOKE e500 family */
-#define CONFIG_MPC8572         1
-#define CONFIG_XPEDITE5370     1
 #define CONFIG_SYS_BOARD_NAME  "XPedite5370"
 #define CONFIG_SYS_FORM_3U_VPX 1
 #define CONFIG_BOARD_EARLY_INIT_R      /* Call board_pre_init */
-#define CONFIG_SYS_GENERIC_BOARD
-#define CONFIG_DISPLAY_BOARDINFO
 
 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE   0xfff80000
 #endif
 
-#define CONFIG_PCI             1       /* Enable PCI/PCIE */
-#define CONFIG_PCI_PNP         1       /* do pci plug-and-play */
 #define CONFIG_PCI_SCAN_SHOW   1       /* show pci devices on startup */
-#define CONFIG_PCIE1           1       /* PCIE controler 1 */
-#define CONFIG_PCIE2           1       /* PCIE controler 2 */
+#define CONFIG_PCIE1           1       /* PCIE controller 1 */
+#define CONFIG_PCIE2           1       /* PCIE controller 2 */
 #define CONFIG_FSL_PCI_INIT    1       /* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE 1   /* indirect PCI bridge support */
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 #define CONFIG_FSL_PCIE_RESET  1       /* need PCIe reset errata */
-#define CONFIG_FSL_LAW         1       /* Use common FSL init code */
-#define CONFIG_FSL_ELBC                1
 
 /*
  * Multicore config
@@ -50,7 +40,6 @@
 /*
  * DDR config
  */
-#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
@@ -58,7 +47,6 @@
 #define SPD_EEPROM_ADDRESS1            0x54    /* Both channels use the */
 #define SPD_EEPROM_ADDRESS2            0x54    /* same SPD data         */
 #define SPD_EEPROM_OFFSET              0x200   /* OFFSET of SPD in EEPROM */
-#define CONFIG_NUM_DDR_CONTROLLERS     2
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 #define CONFIG_CHIP_SELECTS_PER_CTRL   1
 #define CONFIG_DDR_ECC
@@ -131,7 +119,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_NAND_BASE_LIST      {CONFIG_SYS_NAND_BASE, \
                                         CONFIG_SYS_NAND_BASE2}
 #define CONFIG_SYS_MAX_NAND_DEVICE     2
-#define CONFIG_SYS_NAND_QUIET_TEST     /* 2nd NAND flash not always populated */
 #define CONFIG_NAND_FSL_ELBC
 
 /*
@@ -215,7 +202,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  * Serial Port
  */
 #define CONFIG_CONS_INDEX              1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -223,22 +209,9 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
 #define CONFIG_SYS_BAUDRATE_TABLE      \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CONFIG_BAUDRATE                        115200
 #define CONFIG_LOADS_ECHO              1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
 
-/*
- * Use the HUSH parser
- */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT               1
-#define CONFIG_OF_BOARD_SETUP          1
-#define CONFIG_OF_STDOUT_VIA_ALIAS     1
-
 /*
  * I2C
  */
@@ -381,29 +354,16 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 /*
  * Command configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DS4510
 #define CONFIG_CMD_DS4510_INFO
 #define CONFIG_CMD_DTT
 #define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
 #define CONFIG_CMD_PCA953X
 #define CONFIG_CMD_PCA953X_INFO
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PCI_ENUM
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_SNTP
 #define CONFIG_CMD_REGINFO
 
 /*
@@ -418,11 +378,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_CMDLINE_EDITING 1               /* add command line history     */
 #define CONFIG_AUTO_COMPLETE   1               /* add autocompletion support */
 #define CONFIG_LOADADDR                0x1000000       /* default location for tftp and bootm */
-#define CONFIG_BOOTDELAY       3               /* -1 disables auto-boot */
 #define CONFIG_PANIC_HANG                      /* do not reset board on panic */
 #define CONFIG_PREBOOT                         /* enable preboot variable */
-#define CONFIG_FIT             1
-#define CONFIG_FIT_VERBOSE     1
 #define CONFIG_INTEGRITY                       /* support booting INTEGRITY OS */
 
 /*
@@ -584,7 +541,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
        "osfile=/home/user/board.uImage\0"                              \
        "fdtfile=/home/user/board.dtb\0"                                \
        "ubootfile=/home/user/u-boot.bin\0"                             \
-       "fdtaddr=c00000\0"                                              \
+       "fdtaddr=0x1e00000\0"                                           \
        "osaddr=0x1000000\0"                                            \
        "loadaddr=0x1000000\0"                                          \
        "prog_uboot1="CONFIG_PROG_UBOOT1"\0"                            \