Move CONFIG_OF_LIBFDT to Kconfig

[people/ms/u-boot.git] / include / configs / zynq-common.h

diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h
index 2d98cd27a9860727a5351aa5c958dbfec5a68635..77edbb8f952814439770041403759cdf72d51f29 100644 (file)
--- a/include/configs/zynq-common.h
+++ b/include/configs/zynq-common.h
@@ -36,39 +36,26 @@
 #define CONFIG_SYS_BAUDRATE_TABLE  \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
 
-/* DCC driver */
-#if defined(CONFIG_ZYNQ_DCC)
-# define CONFIG_ARM_DCC
-#else
-# define CONFIG_ZYNQ_SERIAL
-#endif
+#define CONFIG_ARM_DCC
+#define CONFIG_ZYNQ_SERIAL
 
 #define CONFIG_ZYNQ_GPIO
-#define CONFIG_CMD_GPIO
 
 /* Ethernet driver */
-#if defined(CONFIG_ZYNQ_GEM0) || defined(CONFIG_ZYNQ_GEM1)
-# define CONFIG_ZYNQ_GEM
+#if defined(CONFIG_ZYNQ_GEM)
 # define CONFIG_MII
 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-# define CONFIG_PHYLIB
 # define CONFIG_PHY_MARVELL
+# define CONFIG_PHY_REALTEK
 # define CONFIG_BOOTP_SERVERIP
 # define CONFIG_BOOTP_BOOTPATH
 # define CONFIG_BOOTP_GATEWAY
 # define CONFIG_BOOTP_HOSTNAME
 # define CONFIG_BOOTP_MAY_FAIL
-# if !defined(CONFIG_ZYNQ_GEM_EMIO0)
-#  define CONFIG_ZYNQ_GEM_EMIO0        0
-# endif
-# if !defined(CONFIG_ZYNQ_GEM_EMIO1)
-#  define CONFIG_ZYNQ_GEM_EMIO1        0
-# endif
 #endif
 
 /* SPI */
 #ifdef CONFIG_ZYNQ_SPI
-# define CONFIG_SPI_FLASH_SST
 # define CONFIG_CMD_SF
 #endif
 
@@ -76,10 +63,6 @@
 #ifdef CONFIG_ZYNQ_QSPI
 # define CONFIG_SF_DEFAULT_SPEED       30000000
 # define CONFIG_SPI_FLASH_ISSI
-# define CONFIG_SPI_FLASH_SPANSION
-# define CONFIG_SPI_FLASH_STMICRO
-# define CONFIG_SPI_FLASH_WINBOND
-# define CONFIG_SPI_FLASH_BAR
 # define CONFIG_CMD_SF
 #endif
 
@@ -100,12 +83,12 @@
 #endif
 
 /* MMC */
-#if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
+#if defined(CONFIG_ZYNQ_SDHCI)
 # define CONFIG_MMC
 # define CONFIG_GENERIC_MMC
 # define CONFIG_SDHCI
-# define CONFIG_ZYNQ_SDHCI
 # define CONFIG_CMD_MMC
+# define CONFIG_ZYNQ_SDHCI_MAX_FREQ    52000000
 #endif
 
 #ifdef CONFIG_ZYNQ_USB
@@ -144,7 +127,7 @@
        "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
        "thor_ram=run dfu_ram_info && thordown 0 ram 0\0"
 
-# if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
+# if defined(CONFIG_ZYNQ_SDHCI)
 #  define CONFIG_DFU_MMC
 #  define DFU_ALT_INFO_MMC \
        "dfu_mmc_info=" \
@@ -210,7 +193,11 @@
 /* Environment */
 #ifndef CONFIG_ENV_IS_NOWHERE
 # ifndef CONFIG_SYS_NO_FLASH
+/* Environment in NOR flash */
 #  define CONFIG_ENV_IS_IN_FLASH
+# elif defined(CONFIG_ZYNQ_QSPI)
+/* Environment in Serial Flash */
+#  define CONFIG_ENV_IS_IN_SPI_FLASH
 # elif defined(CONFIG_SYS_NO_FLASH)
 #  define CONFIG_ENV_IS_NOWHERE
 # endif
@@ -240,8 +227,7 @@
        "usbboot=if usb start; then " \
                        "echo Copying FIT from USB to RAM... && " \
                        "load usb 0 ${load_addr} ${fit_image} && " \
-                       "bootm ${load_addr}\0" \
-               "fi\0" \
+                       "bootm ${load_addr}; fi\0" \
                DFU_ALT_INFO
 
 #define CONFIG_BOOTCOMMAND             "run $modeboot"
@@ -288,9 +274,6 @@
 #define CONFIG_CMD_FPGA_LOADBP
 #define CONFIG_CMD_FPGA_LOADFS
 
-/* Open Firmware flat tree */
-#define CONFIG_OF_LIBFDT
-
 /* FIT support */
 #define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */
 
@@ -301,10 +284,7 @@
 #define CONFIG_SYS_BOOTM_LEN   (60 * 1024 * 1024)
 
 /* Boot FreeBSD/vxWorks from an ELF image */
-#if defined(CONFIG_ZYNQ_BOOT_FREEBSD)
-# define CONFIG_API
-# define CONFIG_SYS_MMC_MAX_DEVICE     1
-#endif
+#define CONFIG_SYS_MMC_MAX_DEVICE      1
 
 #define CONFIG_SYS_LDSCRIPT  "arch/arm/mach-zynq/u-boot.lds"
 
@@ -321,18 +301,23 @@
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_RAM_DEVICE
 
 #define CONFIG_SPL_LDSCRIPT    "arch/arm/mach-zynq/u-boot-spl.lds"
 
 /* MMC support */
-#ifdef CONFIG_ZYNQ_SDHCI0
+#ifdef CONFIG_ZYNQ_SDHCI
 #define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      0x200 /* 256 KB */
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
 #define CONFIG_SPL_LIBDISK_SUPPORT
 #define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot.img"
+#ifdef CONFIG_OF_SEPARATE
+# define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot-dtb.img"
+#else
+# define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot.img"
+#endif
 #endif
 
 /* Disable dcache for SPL just for sure */
@@ -376,16 +361,16 @@
 /* The highest 64k OCM address */
 #define OCM_HIGH_ADDR  0xffff0000
 
-/* Just define any reasonable size */
-#define CONFIG_SPL_STACK_SIZE  0x1000
-
-/* SPL stack position - and stack goes down */
-#define CONFIG_SPL_STACK       (OCM_HIGH_ADDR + CONFIG_SPL_STACK_SIZE)
-
 /* On the top of OCM space */
-#define CONFIG_SYS_SPL_MALLOC_START    (CONFIG_SPL_STACK + \
-                                        GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_SPL_MALLOC_SIZE     0x1000
+#define CONFIG_SYS_SPL_MALLOC_START    OCM_HIGH_ADDR
+#define CONFIG_SYS_SPL_MALLOC_SIZE     0x2000
+
+/*
+ * SPL stack position - and stack goes down
+ * 0xfffffe00 is used for putting wfi loop.
+ * Set it up as limit for now.
+ */
+#define CONFIG_SPL_STACK       0xfffffe00
 
 /* BSS setup */
 #define CONFIG_SPL_BSS_START_ADDR      0x100000