#define SPI_TX_BYTE BIT(8) /* transmit with 1 wire byte */
#define SPI_TX_DUAL BIT(9) /* transmit with 2 wires */
#define SPI_TX_QUAD BIT(10) /* transmit with 4 wires */
-
-/* SPI mode_rx flags */
-#define SPI_RX_SLOW BIT(0) /* receive with 1 wire slow */
-#define SPI_RX_FAST BIT(1) /* receive with 1 wire fast */
-#define SPI_RX_DUAL BIT(2) /* receive with 2 wires */
-#define SPI_RX_QUAD BIT(3) /* receive with 4 wires */
-
-/* SPI bus connection options - see enum spi_dual_flash */
-#define SPI_CONN_DUAL_SHARED (1 << 0)
-#define SPI_CONN_DUAL_SEPARATED (1 << 1)
+#define SPI_RX_SLOW BIT(11) /* receive with 1 wire slow */
+#define SPI_RX_DUAL BIT(12) /* receive with 2 wires */
+#define SPI_RX_QUAD BIT(13) /* receive with 4 wires */
/* Header byte that marks the start of the message */
#define SPI_PREAMBLE_END_BYTE 0xec
* @cs: Chip select number (0..n-1)
* @max_hz: Maximum bus speed that this slave can tolerate
* @mode: SPI mode to use for this device (see SPI mode flags)
- * @mode_rx: SPI RX mode to use for this slave (see SPI mode_rx flags)
*/
struct dm_spi_slave_platdata {
unsigned int cs;
uint max_hz;
uint mode;
- u8 mode_rx;
};
#endif /* CONFIG_DM_SPI */
* bus (bus->seq) so does not need to be stored
* @cs: ID of the chip select connected to the slave.
* @mode: SPI mode to use for this slave (see SPI mode flags)
- * @mode_rx: SPI RX mode to use for this slave (see SPI mode_rx flags)
* @wordlen: Size of SPI word in number of bits
+ * @max_read_size: If non-zero, the maximum number of bytes which can
+ * be read at once.
* @max_write_size: If non-zero, the maximum number of bytes which can
- * be written at once, excluding command bytes.
+ * be written at once.
* @memory_map: Address of read-only SPI flash access.
- * @option: Varies SPI bus options - separate, shared bus.
* @flags: Indication of SPI flags.
*/
struct spi_slave {
unsigned int cs;
#endif
uint mode;
- u8 mode_rx;
unsigned int wordlen;
+ unsigned int max_read_size;
unsigned int max_write_size;
void *memory_map;
- u8 option;
u8 flags;
#define SPI_XFER_BEGIN BIT(0) /* Assert CS before transfer */
#define SPI_XFER_ONCE (SPI_XFER_BEGIN | SPI_XFER_END)
#define SPI_XFER_MMAP BIT(2) /* Memory Mapped start */
#define SPI_XFER_MMAP_END BIT(3) /* Memory Mapped End */
-#define SPI_XFER_U_PAGE BIT(4)
};
/**
return ret < 0 ? ret : din[1];
}
-/**
- * Set up a SPI slave for a particular device tree node
- *
- * This calls spi_setup_slave() with the correct bus number. Call
- * spi_free_slave() to free it later.
- *
- * @param blob: Device tree blob
- * @param slave_node: Slave node to use
- * @param spi_node: SPI peripheral node to use
- * @return pointer to new spi_slave structure
- */
-struct spi_slave *spi_setup_slave_fdt(const void *blob, int slave_node,
- int spi_node);
-
-/**
- * spi_base_setup_slave_fdt() - helper function to set up a SPI slace
- *
- * This decodes SPI properties from the slave node to determine the
- * chip select and SPI parameters.
- *
- * @blob: Device tree blob
- * @busnum: Bus number to use
- * @node: Device tree node for the SPI bus
- */
-struct spi_slave *spi_base_setup_slave_fdt(const void *blob, int busnum,
- int node);
-
#ifdef CONFIG_DM_SPI
/**
* @node: Node offset to read from
* @plat: Place to put the decoded information
*/
-int spi_slave_ofdata_to_platdata(const void *blob, int node,
+int spi_slave_ofdata_to_platdata(struct udevice *dev,
struct dm_spi_slave_platdata *plat);
/**
struct udevice *bus, struct udevice *slave,
struct udevice **emulp);
+/**
+ * Claim the bus and prepare it for communication with a given slave.
+ *
+ * This must be called before doing any transfers with a SPI slave. It
+ * will enable and initialize any SPI hardware as necessary, and make
+ * sure that the SCK line is in the correct idle state. It is not
+ * allowed to claim the same bus for several slaves without releasing
+ * the bus in between.
+ *
+ * @dev: The SPI slave device
+ *
+ * Returns: 0 if the bus was claimed successfully, or a negative value
+ * if it wasn't.
+ */
+int dm_spi_claim_bus(struct udevice *dev);
+
+/**
+ * Release the SPI bus
+ *
+ * This must be called once for every call to dm_spi_claim_bus() after
+ * all transfers have finished. It may disable any SPI hardware as
+ * appropriate.
+ *
+ * @slave: The SPI slave device
+ */
+void dm_spi_release_bus(struct udevice *dev);
+
+/**
+ * SPI transfer
+ *
+ * This writes "bitlen" bits out the SPI MOSI port and simultaneously clocks
+ * "bitlen" bits in the SPI MISO port. That's just the way SPI works.
+ *
+ * The source of the outgoing bits is the "dout" parameter and the
+ * destination of the input bits is the "din" parameter. Note that "dout"
+ * and "din" can point to the same memory location, in which case the
+ * input data overwrites the output data (since both are buffered by
+ * temporary variables, this is OK).
+ *
+ * dm_spi_xfer() interface:
+ * @dev: The SPI slave device which will be sending/receiving the data.
+ * @bitlen: How many bits to write and read.
+ * @dout: Pointer to a string of bits to send out. The bits are
+ * held in a byte array and are sent MSB first.
+ * @din: Pointer to a string of bits that will be filled in.
+ * @flags: A bitwise combination of SPI_XFER_* flags.
+ *
+ * Returns: 0 on success, not 0 on failure
+ */
+int dm_spi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags);
+
/* Access the operations for a SPI device */
#define spi_get_ops(dev) ((struct dm_spi_ops *)(dev)->driver->ops)
#define spi_emul_get_ops(dev) ((struct dm_spi_emul_ops *)(dev)->driver->ops)
projects / people / ms / u-boot.git / blobdiff