X-Git-Url: http://git.ipfire.org/?p=people%2Fms%2Fu-boot.git;a=blobdiff_plain;f=include%2Fconfigs%2Fmicroblaze-generic.h;h=6ac19a0d928428fc34fda14e4275179f71a69982;hp=6e3c80b1435014a7c424112fcb71e091d786b8cf;hb=69e173eb57d1f4848f070c83456096ba5d2ba1b4;hpb=54e24d33324a1a4599d9f830a8671a61c45300fc

diff --git a/include/configs/microblaze-generic.h b/include/configs/microblaze-generic.h
index 6e3c80b143..6ac19a0d92 100644
--- a/include/configs/microblaze-generic.h
+++ b/include/configs/microblaze-generic.h
@@ -37,40 +37,15 @@
 # define CONFIG_SYS_BAUDRATE_TABLE \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
 
-#if XILINX_UART16550_BASEADDR
-# define CONFIG_SYS_NS16550_SERIAL
-# if defined(__MICROBLAZEEL__)
-#  define CONFIG_SYS_NS16550_REG_SIZE	-4
-# else
-#  define CONFIG_SYS_NS16550_REG_SIZE	4
-# endif
-# define CONFIG_CONS_INDEX		1
-# define CONFIG_SYS_NS16550_COM1 \
-		((XILINX_UART16550_BASEADDR & ~0xF) + 0x1000)
-# define CONFIG_SYS_NS16550_CLK	XILINX_UART16550_CLOCK_HZ
-#endif
-
 /* setting reset address */
 /*#define	CONFIG_SYS_RESET_ADDRESS	CONFIG_SYS_TEXT_BASE*/
 
-/* ethernet */
-#undef CONFIG_SYS_ENET
-#if defined(XILINX_EMACLITE_BASEADDR) || defined(CONFIG_OF_CONTROL)
-# define CONFIG_XILINX_EMACLITE	1
-# define CONFIG_SYS_ENET
-#endif
-#if defined(XILINX_AXIEMAC_BASEADDR)
-# define CONFIG_XILINX_AXIEMAC	1
-# define CONFIG_SYS_ENET
-#endif
-
-#undef ET_DEBUG
-
 /* gpio */
 #ifdef XILINX_GPIO_BASEADDR
 # define CONFIG_XILINX_GPIO
 # define CONFIG_SYS_GPIO_0_ADDR		XILINX_GPIO_BASEADDR
 #endif
+#define CONFIG_BOARD_LATE_INIT
 
 /* interrupt controller */
 #ifdef XILINX_INTC_BASEADDR
@@ -94,13 +69,6 @@
 # endif
 #endif
 
-#if !defined(CONFIG_OF_CONTROL) || \
-	(defined(CONFIG_SPL_BUILD) && !defined(CONFIG_SPL_OF_CONTROL))
-/* ddr sdram - main memory */
-# define CONFIG_SYS_SDRAM_BASE	XILINX_RAM_START
-# define CONFIG_SYS_SDRAM_SIZE	XILINX_RAM_SIZE
-#endif
-
 #define CONFIG_SYS_MALLOC_LEN	0xC0000
 
 /* Stack location before relocation */
@@ -189,16 +157,6 @@
 #endif /* !SPIFLASH */
 #endif /* !FLASH */
 
-/* system ace */
-#ifdef XILINX_SYSACE_BASEADDR
-# define CONFIG_SYSTEMACE
-/* #define DEBUG_SYSTEMACE */
-# define SYSTEMACE_CONFIG_FPGA
-# define CONFIG_SYS_SYSTEMACE_BASE	XILINX_SYSACE_BASEADDR
-# define CONFIG_SYS_SYSTEMACE_WIDTH	XILINX_SYSACE_MEM_WIDTH
-# define CONFIG_DOS_PARTITION
-#endif
-
 #if defined(XILINX_USE_ICACHE)
 # define CONFIG_ICACHE
 #else
@@ -236,17 +194,6 @@
 # undef CONFIG_CMD_CACHE
 #endif
 
-#ifdef CONFIG_SYS_ENET
-# define CONFIG_CMD_PING
-# define CONFIG_CMD_DHCP
-# define CONFIG_CMD_TFTPPUT
-#endif
-
-#if defined(CONFIG_SYSTEMACE)
-# define CONFIG_CMD_EXT2
-# define CONFIG_CMD_FAT
-#endif
-
 #if defined(FLASH)
 # define CONFIG_CMD_JFFS2
 # define CONFIG_CMD_UBI
@@ -306,7 +253,7 @@
 #define	CONFIG_SYS_MAXARGS	15
 #define	CONFIG_SYS_LONGHELP
 /* default load address */
-#define	CONFIG_SYS_LOAD_ADDR	XILINX_RAM_START
+#define	CONFIG_SYS_LOAD_ADDR	0
 
 #define	CONFIG_BOOTDELAY	-1	/* -1 disables auto-boot */
 #define	CONFIG_BOOTARGS		"root=romfs"
@@ -333,36 +280,30 @@
 
 #define CONFIG_CMDLINE_EDITING
 
-#define CONFIG_NETCONSOLE
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
 /* Enable flat device tree support */
 #define CONFIG_LMB		1
 #define CONFIG_FIT		1
-#define CONFIG_OF_LIBFDT	1
 
 #if defined(CONFIG_XILINX_AXIEMAC)
 # define CONFIG_MII		1
 # define CONFIG_CMD_MII		1
 # define CONFIG_PHY_GIGE	1
 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	1
-# define CONFIG_PHYLIB		1
 # define CONFIG_PHY_ATHEROS	1
 # define CONFIG_PHY_BROADCOM	1
 # define CONFIG_PHY_DAVICOM	1
 # define CONFIG_PHY_LXT		1
 # define CONFIG_PHY_MARVELL	1
 # define CONFIG_PHY_MICREL	1
+# define CONFIG_PHY_MICREL_KSZ9021
 # define CONFIG_PHY_NATSEMI	1
 # define CONFIG_PHY_REALTEK	1
 # define CONFIG_PHY_VITESSE	1
 #else
 # undef CONFIG_MII
 # undef CONFIG_CMD_MII
-# undef CONFIG_PHYLIB
 #endif
 
 /* SPL part */