#include <dt-bindings/clock/bcm2835-aux.h>
#include <dt-bindings/gpio/gpio.h>
+/* firmware-provided startup stubs live here, where the secondary CPUs are
+ * spinning.
+ */
+/memreserve/ 0x00000000 0x00001000;
+
/* This include file covers the common peripherals and configuration between
* bcm2835 and bcm2836 implementations, leaving the CPU configuration to
* bcm2835.dtsi and bcm2836.dtsi.
bootargs = "earlyprintk console=ttyAMA0";
};
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&thermal>;
+
+ trips {
+ cpu-crit {
+ temperature = <80000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ };
+ };
+ };
+
soc: soc {
compatible = "simple-bus";
#address-cells = <1>;
#clock-cells = <1>;
reg = <0x7e101000 0x2000>;
- /* CPRMAN derives everything from the platform's
- * oscillator.
+ /* CPRMAN derives almost everything from the
+ * platform's oscillator. However, the DSI
+ * pixel clocks come from the DSI analog PHY.
*/
- clocks = <&clk_osc>;
+ clocks = <&clk_osc>,
+ <&dsi0 0>, <&dsi0 1>, <&dsi0 2>,
+ <&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
};
rng@7e104000 {
reg = <0x7e104000 0x10>;
};
- mailbox: mailbox@7e00b800 {
+ mailbox: mailbox@7e00b880 {
compatible = "brcm,bcm2835-mbox";
reg = <0x7e00b880 0x40>;
interrupts = <0 1>;
interrupt-controller;
#interrupt-cells = <2>;
+
+ /* Defines pin muxing groups according to
+ * BCM2835-ARM-Peripherals.pdf page 102.
+ *
+ * While each pin can have its mux selected
+ * for various functions individually, some
+ * groups only make sense to switch to a
+ * particular function together.
+ */
+ dpi_gpio0: dpi_gpio0 {
+ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
+ 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27>;
+ brcm,function = <BCM2835_FSEL_ALT2>;
+ };
+ emmc_gpio22: emmc_gpio22 {
+ brcm,pins = <22 23 24 25 26 27>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+ emmc_gpio34: emmc_gpio34 {
+ brcm,pins = <34 35 36 37 38 39>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ brcm,pull = <BCM2835_PUD_OFF
+ BCM2835_PUD_UP
+ BCM2835_PUD_UP
+ BCM2835_PUD_UP
+ BCM2835_PUD_UP
+ BCM2835_PUD_UP>;
+ };
+ emmc_gpio48: emmc_gpio48 {
+ brcm,pins = <48 49 50 51 52 53>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+
+ gpclk0_gpio4: gpclk0_gpio4 {
+ brcm,pins = <4>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ gpclk1_gpio5: gpclk1_gpio5 {
+ brcm,pins = <5>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ gpclk1_gpio42: gpclk1_gpio42 {
+ brcm,pins = <42>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ gpclk1_gpio44: gpclk1_gpio44 {
+ brcm,pins = <44>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ gpclk2_gpio6: gpclk2_gpio6 {
+ brcm,pins = <6>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ gpclk2_gpio43: gpclk2_gpio43 {
+ brcm,pins = <43>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+
+ i2c0_gpio0: i2c0_gpio0 {
+ brcm,pins = <0 1>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ i2c0_gpio28: i2c0_gpio28 {
+ brcm,pins = <28 29>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ i2c0_gpio44: i2c0_gpio44 {
+ brcm,pins = <44 45>;
+ brcm,function = <BCM2835_FSEL_ALT1>;
+ };
+ i2c1_gpio2: i2c1_gpio2 {
+ brcm,pins = <2 3>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ i2c1_gpio44: i2c1_gpio44 {
+ brcm,pins = <44 45>;
+ brcm,function = <BCM2835_FSEL_ALT2>;
+ };
+ i2c_slave_gpio18: i2c_slave_gpio18 {
+ brcm,pins = <18 19 20 21>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+
+ jtag_gpio4: jtag_gpio4 {
+ brcm,pins = <4 5 6 12 13>;
+ brcm,function = <BCM2835_FSEL_ALT4>;
+ };
+ jtag_gpio22: jtag_gpio22 {
+ brcm,pins = <22 23 24 25 26 27>;
+ brcm,function = <BCM2835_FSEL_ALT4>;
+ };
+
+ pcm_gpio18: pcm_gpio18 {
+ brcm,pins = <18 19 20 21>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ pcm_gpio28: pcm_gpio28 {
+ brcm,pins = <28 29 30 31>;
+ brcm,function = <BCM2835_FSEL_ALT2>;
+ };
+
+ pwm0_gpio12: pwm0_gpio12 {
+ brcm,pins = <12>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ pwm0_gpio18: pwm0_gpio18 {
+ brcm,pins = <18>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ pwm0_gpio40: pwm0_gpio40 {
+ brcm,pins = <40>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ pwm1_gpio13: pwm1_gpio13 {
+ brcm,pins = <13>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ pwm1_gpio19: pwm1_gpio19 {
+ brcm,pins = <19>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ pwm1_gpio41: pwm1_gpio41 {
+ brcm,pins = <41>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ pwm1_gpio45: pwm1_gpio45 {
+ brcm,pins = <45>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+
+ sdhost_gpio48: sdhost_gpio48 {
+ brcm,pins = <48 49 50 51 52 53>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+
+ spi0_gpio7: spi0_gpio7 {
+ brcm,pins = <7 8 9 10 11>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ spi0_gpio35: spi0_gpio35 {
+ brcm,pins = <35 36 37 38 39>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ spi1_gpio16: spi1_gpio16 {
+ brcm,pins = <16 17 18 19 20 21>;
+ brcm,function = <BCM2835_FSEL_ALT4>;
+ };
+ spi2_gpio40: spi2_gpio40 {
+ brcm,pins = <40 41 42 43 44 45>;
+ brcm,function = <BCM2835_FSEL_ALT4>;
+ };
+
+ uart0_gpio14: uart0_gpio14 {
+ brcm,pins = <14 15>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ /* Separate from the uart0_gpio14 group
+ * because it conflicts with spi1_gpio16, and
+ * people often run uart0 on the two pins
+ * without flow control.
+ */
+ uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
+ brcm,pins = <16 17>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+ uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 {
+ brcm,pins = <30 31>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+ uart0_gpio32: uart0_gpio32 {
+ brcm,pins = <32 33>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+ uart0_gpio36: uart0_gpio36 {
+ brcm,pins = <36 37>;
+ brcm,function = <BCM2835_FSEL_ALT2>;
+ };
+ uart0_ctsrts_gpio38: uart0_ctsrts_gpio38 {
+ brcm,pins = <38 39>;
+ brcm,function = <BCM2835_FSEL_ALT2>;
+ };
+
+ uart1_gpio14: uart1_gpio14 {
+ brcm,pins = <14 15>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
+ brcm,pins = <16 17>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ uart1_gpio32: uart1_gpio32 {
+ brcm,pins = <32 33>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
+ brcm,pins = <30 31>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ uart1_gpio40: uart1_gpio40 {
+ brcm,pins = <40 41>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
+ brcm,pins = <42 43>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
};
uart0: serial@7e201000 {
arm,primecell-periphid = <0x00241011>;
};
+ sdhost: mmc@7e202000 {
+ compatible = "brcm,bcm2835-sdhost";
+ reg = <0x7e202000 0x100>;
+ interrupts = <2 24>;
+ clocks = <&clocks BCM2835_CLOCK_VPU>;
+ dmas = <&dma 13>;
+ dma-names = "rx-tx";
+ status = "disabled";
+ };
+
i2s: i2s@7e203000 {
compatible = "brcm,bcm2835-i2s";
reg = <0x7e203000 0x20>,
interrupts = <2 14>; /* pwa1 */
};
+ dsi0: dsi@7e209000 {
+ compatible = "brcm,bcm2835-dsi0";
+ reg = <0x7e209000 0x78>;
+ interrupts = <2 4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+
+ clocks = <&clocks BCM2835_PLLA_DSI0>,
+ <&clocks BCM2835_CLOCK_DSI0E>,
+ <&clocks BCM2835_CLOCK_DSI0P>;
+ clock-names = "phy", "escape", "pixel";
+
+ clock-output-names = "dsi0_byte",
+ "dsi0_ddr2",
+ "dsi0_ddr";
+
+ };
+
+ thermal: thermal@7e212000 {
+ compatible = "brcm,bcm2835-thermal";
+ reg = <0x7e212000 0x8>;
+ clocks = <&clocks BCM2835_CLOCK_TSENS>;
+ #thermal-sensor-cells = <0>;
+ status = "disabled";
+ };
+
aux: aux@0x7e215000 {
compatible = "brcm,bcm2835-aux";
#clock-cells = <1>;
interrupts = <2 1>;
};
+ dsi1: dsi@7e700000 {
+ compatible = "brcm,bcm2835-dsi1";
+ reg = <0x7e700000 0x8c>;
+ interrupts = <2 12>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+
+ clocks = <&clocks BCM2835_PLLD_DSI1>,
+ <&clocks BCM2835_CLOCK_DSI1E>,
+ <&clocks BCM2835_CLOCK_DSI1P>;
+ clock-names = "phy", "escape", "pixel";
+
+ clock-output-names = "dsi1_byte",
+ "dsi1_ddr2",
+ "dsi1_ddr";
+
+ status = "disabled";
+ };
+
i2c1: i2c@7e804000 {
compatible = "brcm,bcm2835-i2c";
reg = <0x7e804000 0x1000>;
status = "disabled";
};
+ vec: vec@7e806000 {
+ compatible = "brcm,bcm2835-vec";
+ reg = <0x7e806000 0x1000>;
+ clocks = <&clocks BCM2835_CLOCK_VEC>;
+ interrupts = <2 27>;
+ status = "disabled";
+ };
+
pixelvalve@7e807000 {
compatible = "brcm,bcm2835-pixelvalve2";
reg = <0x7e807000 0x100>;
clocks = <&clocks BCM2835_PLLH_PIX>,
<&clocks BCM2835_CLOCK_HSM>;
clock-names = "pixel", "hdmi";
+ dmas = <&dma 17>;
+ dma-names = "audio-rx";
status = "disabled";
};
interrupts = <1 9>;
#address-cells = <1>;
#size-cells = <0>;
+ clocks = <&clk_usb>;
+ clock-names = "otg";
+ phys = <&usbphy>;
+ phy-names = "usb2-phy";
};
v3d: v3d@7ec00000 {
clock-frequency = <19200000>;
};
+ clk_usb: clock@4 {
+ compatible = "fixed-clock";
+ reg = <4>;
+ #clock-cells = <0>;
+ clock-output-names = "otg";
+ clock-frequency = <480000000>;
+ };
+ };
+
+ usbphy: phy {
+ compatible = "usb-nop-xceiv";
};
};
projects / people / ms / u-boot.git / commitdiff
