mx53smd i.MX53
mx6qsabresd i.MX6Q
mx6qsabreauto i.MX6Q
+ wandboard i.MX6DL/S
Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
0x00000000, 0x00000000, 0x00010101, 0x01010101,
0x000f0f01, 0x0f02020a, 0x00000000, 0x00010101,
0x00000100, 0x00000100, 0x00000000, 0x00000002,
- 0x01010000, 0x05060302, 0x06005003, 0x0a0000c8,
- 0x02009c40, 0x0000030c, 0x0036a609, 0x031a0612,
+ 0x01010000, 0x07080403, 0x06005003, 0x0a0000c8,
+ 0x02009c40, 0x0002030c, 0x0036a609, 0x031a0612,
0x02030202, 0x00c8001c, 0x00000000, 0x00000000,
0x00012100, 0xffff0303, 0x00012100, 0xffff0303,
0x00012100, 0xffff0303, 0x00012100, 0xffff0303,
0x00000003, 0x00000000, 0x00000000, 0x00000000,
0x00000000, 0x00000000, 0x00000000, 0x00000000,
0x00000000, 0x00000000, 0x00000612, 0x01000F02,
- 0x06120612, 0x00000200, 0x00020007, 0xf5014b27,
- 0xf5014b27, 0xf5014b27, 0xf5014b27, 0x07000300,
- 0x07000300, 0x07000300, 0x07000300, 0x00000006,
+ 0x06120612, 0x00000200, 0x00020007, 0xf4004a27,
+ 0xf4004a27, 0xf4004a27, 0xf4004a27, 0x07000300,
+ 0x07000300, 0x07400300, 0x07400300, 0x00000005,
0x00000000, 0x00000000, 0x01000000, 0x01020408,
0x08040201, 0x000f1133, 0x00000000, 0x00001f04,
0x00001f04, 0x00001f04, 0x00001f04, 0x00001f04,
0x00000000, 0x00000000, 0x00000000, 0x00000000,
0x00000000, 0x00000000, 0x00000000, 0x00000000,
0x00000000, 0x00000000, 0x00000000, 0x00000000,
- 0x00000000, 0x00000000, 0x00010000, 0x00020304,
- 0x00000004, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00010000, 0x00030404,
+ 0x00000003, 0x00000000, 0x00000000, 0x00000000,
0x00000000, 0x00000000, 0x00000000, 0x01010000,
0x01000000, 0x03030000, 0x00010303, 0x01020202,
0x00000000, 0x02040303, 0x21002103, 0x00061200,
- 0x06120612, 0x04320432, 0x04320432, 0x00040004,
+ 0x06120612, 0x04420442, 0x04420442, 0x00040004,
0x00040004, 0x00000000, 0x00000000, 0x00000000,
- 0x00000000, 0x00010001
+ 0x00000000, 0xffffffff
/*
* i.MX23 DDR at 133MHz
return (type << 12) | (reg + 0x10);
}
+#ifdef CONFIG_REVISION_TAG
+u32 __weak get_board_rev(void)
+{
+ u32 cpurev = get_cpu_rev();
+ u32 type = ((cpurev >> 12) & 0xff);
+ if (type == MXC_CPU_MX6SOLO)
+ cpurev = (MXC_CPU_MX6DL) << 12 | (cpurev & 0xFFF);
+
+ return cpurev;
+}
+#endif
+
void init_aips(void)
{
struct aipstz_regs *aips1, *aips2;
COBJS-$(CONFIG_I2C_MXC) += i2c-mxv7.o
endif
COBJS-$(CONFIG_CMD_BMODE) += cmd_bmode.o
+COBJS-$(CONFIG_CMD_HDMIDETECT) += cmd_hdmidet.o
COBJS := $(sort $(COBJS-y))
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
--- /dev/null
+/*
+ * Copyright (C) 2012 Boundary Devices Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/io.h>
+
+static int do_hdmidet(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
+ u8 reg = readb(&hdmi->phy_stat0) & HDMI_PHY_HPD;
+ return (reg&HDMI_PHY_HPD) ? 0 : 1;
+}
+
+U_BOOT_CMD(hdmidet, 1, 1, do_hdmidet,
+ "detect HDMI monitor",
+ ""
+);
DECLARE_GLOBAL_DATA_PTR;
-#define timestamp (gd->arch.tbl)
-#define lastinc (gd->arch.lastinc)
-
static inline unsigned long long tick_to_time(unsigned long long tick)
{
tick *= CONFIG_SYS_HZ;
int timer_init(void)
{
int i;
- ulong val;
/* setup GP Timer 1 */
__raw_writel(GPTCR_SWR, &cur_gpt->control);
i = __raw_readl(&cur_gpt->control);
__raw_writel(i | GPTCR_CLKSOURCE_32 | GPTCR_TEN, &cur_gpt->control);
- val = __raw_readl(&cur_gpt->counter);
- lastinc = val / (MXC_CLK32 / CONFIG_SYS_HZ);
- timestamp = 0;
+ gd->arch.tbl = __raw_readl(&cur_gpt->counter);
+ gd->arch.tbu = 0;
return 0;
}
{
ulong now = __raw_readl(&cur_gpt->counter); /* current tick value */
- if (now >= lastinc) {
- /*
- * normal mode (non roll)
- * move stamp forward with absolut diff ticks
- */
- timestamp += (now - lastinc);
- } else {
- /* we have rollover of incrementer */
- timestamp += (0xFFFFFFFF - lastinc) + now;
- }
- lastinc = now;
- return timestamp;
+ /* increment tbu if tbl has rolled over */
+ if (now < gd->arch.tbl)
+ gd->arch.tbu++;
+ gd->arch.tbl = now;
+ return (((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;
}
ulong get_timer_masked(void)
#define NO_MUX_I 0
#define NO_PAD_I 0
enum {
+ MX6_PAD_CSI0_DAT10__UART1_TXD = IOMUX_PAD(0x0360, 0x004C, 3, 0x0000, 0, 0),
+ MX6_PAD_CSI0_DAT11__UART1_RXD = IOMUX_PAD(0x0364, 0x0050, 3, 0x08FC, 1, 0),
MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK = IOMUX_PAD(0x03B0, 0x009C, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15 = IOMUX_PAD(0x03B4, 0x00A0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
MX6_PAD_DI0_PIN2__IPU1_DI0_PIN2 = IOMUX_PAD(0x03B8, 0x00A4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
MX6_PAD_EIM_D27__UART2_RXD = IOMUX_PAD(0x0540, 0x0170, 4, 0x0904, 1, 0),
MX6_PAD_EIM_D28__I2C1_SDA = IOMUX_PAD(0x0544, 0x0174, 1 | IOMUX_CONFIG_SION, 0x086C, 1, 0),
MX6_PAD_EIM_D28__GPIO_3_28 = IOMUX_PAD(0x0544, 0x0174, 5, 0x0000, 0, 0),
+ MX6_PAD_EIM_D29__GPIO_3_29 = IOMUX_PAD(0x0548, 0x0178, 5, 0x0000, 0, 0),
MX6_PAD_ENET_MDC__ENET_MDC = IOMUX_PAD(0x05B8, 0x01E8, 1, 0x0000, 0, 0),
MX6_PAD_ENET_MDIO__ENET_MDIO = IOMUX_PAD(0x05BC, 0x01EC, 1, 0x0810, 0, 0),
MX6_PAD_ENET_REF_CLK__ENET_TX_CLK = IOMUX_PAD(0x05C0, 0x01F0, 1, 0x0000, 0, 0),
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+ usdhc_cfg[0].max_bus_width = 4;
+ usdhc_cfg[1].max_bus_width = 4;
+
for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
switch (index) {
case 0:
}
#endif
-u32 get_board_rev(void)
-{
- return 0x63000;
-}
-
#ifdef CONFIG_MXC_SPI
iomux_v3_cfg_t const ecspi1_pads[] = {
/* SS1 */
#include <asm/errno.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <miiphy.h>
return 0;
}
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+ /* 4 bit bus width */
+ {"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+ {NULL, 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+ add_board_boot_modes(board_boot_modes);
+#endif
+
+ return 0;
+}
+
int checkboard(void)
{
int rev = mx6sabre_rev();
MX6Q SABRELITE U-Boot > mmc dev 0
MX6Q SABRELITE U-Boot > mmc read 0x10800000 0 200
- MX6Q SABRELITE U-Boot > sf probe 1
+ MX6Q SABRELITE U-Boot > sf probe
MX6Q SABRELITE U-Boot > sf erase 0 0x40000
MX6Q SABRELITE U-Boot > sf write 0x10800000 0 0x40000
To build U-Boot for the SabreLite board:
make mx6qsabrelite_config
- make u-boot.imx
+ make
To copy the resulting u-boot.imx to the SD card:
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+ usdhc_cfg[0].max_bus_width = 4;
+ usdhc_cfg[1].max_bus_width = 4;
+
for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
switch (index) {
case 0:
}
#endif
-u32 get_board_rev(void)
-{
- return 0x63000 ;
-}
-
#ifdef CONFIG_MXC_SPI
iomux_v3_cfg_t const ecspi1_pads[] = {
/* SS1 */
#include <asm/errno.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <miiphy.h>
#include <netdev.h>
+
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
int board_mmc_getcd(struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
switch (cfg->esdhc_base) {
case USDHC2_BASE_ADDR:
- return !gpio_get_value(USDHC2_CD_GPIO);
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ break;
case USDHC3_BASE_ADDR:
- return !gpio_get_value(USDHC3_CD_GPIO);
- default:
- return 1; /* eMMC/uSDHC4 is always present */
+ ret = !gpio_get_value(USDHC3_CD_GPIO);
+ break;
+ case USDHC4_BASE_ADDR:
+ ret = 1; /* eMMC/uSDHC4 is always present */
+ break;
}
+
+ return ret;
}
int board_mmc_init(bd_t *bis)
{
int i;
+ /*
+ * According to the board_mmc_init() the following map is done:
+ * (U-boot device node) (Physical Port)
+ * mmc0 SD2
+ * mmc1 SD3
+ * mmc2 eMMC
+ */
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
switch (i) {
case 0:
return 0;
}
-u32 get_board_rev(void)
-{
- return 0x63000;
-}
-
int board_early_init_f(void)
{
setup_iomux_uart();
return 0;
}
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+ /* 4 bit bus width */
+ {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+ {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+ /* 8 bit bus width */
+ {"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
+ {NULL, 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+ add_board_boot_modes(board_boot_modes);
+#endif
+
+ return 0;
+}
+
int checkboard(void)
{
puts("Board: MX6Q-SabreSD\n");
--- /dev/null
+#
+# (C) Copyright 2013 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := wandboard.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+U-Boot for Wandboard
+--------------------
+
+This file contains information for the port of U-Boot to the Wandboard.
+
+Wandboard is a development board that has two variants: one version based
+on mx6 dual lite and another one based on mx6 solo.
+
+For more details about Wandboard, please refer to:
+http://www.wandboard.org/
+
+Building U-boot for Wandboard
+-----------------------------
+
+To build U-Boot for the Wandboard Dual Lite version:
+
+$ make wanboard_dl_config
+$ make
+
+To build U-Boot for the Wandboard Solo version:
+
+$ make wanboard_solo_config
+$ make
+
+Flashing U-boot into the SD card
+--------------------------------
+
+- After the 'make' command completes, the generated 'u-boot.imx' binary must be
+flashed into the SD card;
+
+$ sudo dd if=u-boot.imx of=/dev/mmcblk0 bs=512 seek=2; sync
+
+(Note - the SD card node may vary, so adjust this as needed).
+
+- Insert the SD card into the slot located in the bottom of the board (same side
+as the mx6 processor)
+
+- Connect the serial cable to the host PC
+
+- Power up the board and U-boot messages will appear in the serial console.
--- /dev/null
+/*
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/io.h>
+#include <asm/sizes.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <miiphy.h>
+#include <netdev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define ETH_PHY_RESET IMX_GPIO_NR(3, 29)
+
+int dram_init(void)
+{
+ gd->ram_size = CONFIG_DDR_MB * SZ_1M;
+
+ return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_CSI0_DAT10__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT11__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+ MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const enet_pads[] = {
+ MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ /* AR8031 PHY Reset */
+ MX6_PAD_EIM_D29__GPIO_3_29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+static void setup_iomux_enet(void)
+{
+ imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+ /* Reset AR8031 PHY */
+ gpio_direction_output(ETH_PHY_RESET, 0);
+ udelay(500);
+ gpio_set_value(ETH_PHY_RESET, 1);
+}
+
+static struct fsl_esdhc_cfg usdhc_cfg[1] = {
+ {USDHC3_BASE_ADDR},
+};
+
+int board_mmc_init(bd_t *bis)
+{
+ imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ usdhc_cfg[0].max_bus_width = 4;
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+static int mx6_rgmii_rework(struct phy_device *phydev)
+{
+ unsigned short val;
+
+ /* To enable AR8031 ouput a 125MHz clk from CLK_25M */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+
+ val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+ val &= 0xffe3;
+ val |= 0x18;
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
+
+ /* introduce tx clock delay */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
+ val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+ val |= 0x0100;
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
+
+ return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ mx6_rgmii_rework(phydev);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int ret;
+
+ setup_iomux_enet();
+
+ ret = cpu_eth_init(bis);
+ if (ret)
+ printf("FEC MXC: %s:failed\n", __func__);
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: Wandboard\n");
+
+ return 0;
+}
apx4devkit arm arm926ejs apx4devkit bluegiga mxs apx4devkit
mx23evk arm arm926ejs mx23evk freescale mxs mx23evk
m28evk arm arm926ejs m28evk denx mxs m28evk
-mx28evk arm arm926ejs mx28evk freescale mxs mx28evk
+mx28evk arm arm926ejs mx28evk freescale mxs mx28evk:ENV_IS_IN_MMC
+mx28evk_nand arm arm926ejs mx28evk freescale mxs mx28evk:ENV_IS_IN_NAND
sc_sps_1 arm arm926ejs sc_sps_1 schulercontrol mxs
nhk8815 arm arm926ejs nhk8815 st nomadik
nhk8815_onenand arm arm926ejs nhk8815 st nomadik nhk8815:BOOT_ONENAND
nitrogen6q2g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q2g.cfg,MX6Q,DDR_MB=2048
nitrogen6s arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512
nitrogen6s1g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s1g.cfg,MX6S,DDR_MB=1024
+wandboard_dl arm armv7 wandboard - mx6 wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DDR_MB=1024
+wandboard_solo arm armv7 wandboard - mx6 wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512
cm_t35 arm armv7 cm_t35 - omap3
omap3_overo arm armv7 overo - omap3
omap3_pandora arm armv7 pandora - omap3
* VDD 5V: To the left (off)
* Hold Button: Down (off)
+
+Environment Storage
+-------------------
+
+There are two targets for mx28evk:
+
+"make mx28evk_config" - store enviroment variables into MMC
+
+or
+
+"make mx28evk_nand_config" - store enviroment variables into NAND flash
+
+Choose the target accordingly.
+
+Note: The mx28evk board does not come with a NAND flash populated from the
+factory. It comes with an empty slot (U23), which allows the insertion of a
+48-pin TSOP flash device.
+
Follow the instructions from doc/README.mx28_common to generate a bootable SD
card.
mmc->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT | MMC_MODE_HC;
+ if (cfg->max_bus_width > 0) {
+ if (cfg->max_bus_width < 8)
+ mmc->host_caps &= ~MMC_MODE_8BIT;
+ if (cfg->max_bus_width < 4)
+ mmc->host_caps &= ~MMC_MODE_4BIT;
+ }
+
if (caps & ESDHC_HOSTCAPBLT_HSS)
mmc->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS;
return -1;
}
- reg_ctrl = reg_read(®s->ctrl);
-
/* Reset spi */
- reg_write(®s->ctrl, (reg_ctrl & ~MXC_CSPICTRL_EN));
- reg_write(®s->ctrl, (reg_ctrl | MXC_CSPICTRL_EN));
+ reg_write(®s->ctrl, 0);
+ reg_write(®s->ctrl, MXC_CSPICTRL_EN);
+
+ reg_ctrl = reg_read(®s->ctrl);
/*
* The following computation is taken directly from Freescale's code.
/*
* SoC configurations
*/
-#define CONFIG_MX23 /* i.MX23 SoC */
-#define CONFIG_MXS_GPIO /* GPIO control */
-#define CONFIG_SYS_HZ 1000 /* Ticks per second */
+#define CONFIG_MX23 /* i.MX23 SoC */
+#define CONFIG_MXS_GPIO /* GPIO control */
+#define CONFIG_SYS_HZ 1000 /* Ticks per second */
-#define CONFIG_MACH_TYPE 4105
+#define CONFIG_MACH_TYPE 4105
#include <asm/arch/regs-base.h>
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_ARCH_MISC_INIT
/*
* SPL
*/
-#define CONFIG_SPL
-#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
-#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs"
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds"
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL
+#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
+#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs"
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
/*
* U-Boot Commands
*/
#include <config_cmd_default.h>
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DOS_PARTITION
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_GPIO
-#define CONFIG_CMD_LED
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_USB
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_LED
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_USB
/*
* Memory configurations
*/
-#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x40000000 /* Base address */
-#define PHYS_SDRAM_1_SIZE 0x08000000 /* Max 128 MB RAM */
-#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */
-#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */
-#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
+#define PHYS_SDRAM_1 0x40000000 /* Base address */
+#define PHYS_SDRAM_1_SIZE 0x08000000 /* Max 128 MB RAM */
+#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */
+#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */
+#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
/* Point initial SP in SRAM so SPL can use it too. */
#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000
* strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
* binary. In case there was more of this mess, 0x100 bytes are skipped.
*/
-#define CONFIG_SYS_TEXT_BASE 0x40000100
+#define CONFIG_SYS_TEXT_BASE 0x40000100
/*
* U-Boot general configurations
*/
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_PROMPT "=> "
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
-#define CONFIG_SYS_PBSIZE \
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT "=> "
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
+#define CONFIG_SYS_PBSIZE \
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
/* Print buffer size */
-#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* Boot argument buffer size */
-#define CONFIG_VERSION_VARIABLE /* U-BOOT version */
-#define CONFIG_AUTO_COMPLETE /* Command auto complete */
-#define CONFIG_CMDLINE_EDITING /* Command history etc */
-#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_VERSION_VARIABLE /* U-BOOT version */
+#define CONFIG_AUTO_COMPLETE /* Command auto complete */
+#define CONFIG_CMDLINE_EDITING /* Command history etc */
+#define CONFIG_SYS_HUSH_PARSER
/*
* Serial Driver
*/
-#define CONFIG_PL011_SERIAL
-#define CONFIG_PL011_CLOCK 24000000
-#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE }
-#define CONFIG_CONS_INDEX 0
-#define CONFIG_BAUDRATE 115200 /* Default baud rate */
+#define CONFIG_PL011_SERIAL
+#define CONFIG_PL011_CLOCK 24000000
+#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE }
+#define CONFIG_CONS_INDEX 0
+#define CONFIG_BAUDRATE 115200 /* Default baud rate */
/*
* Status LED
*/
-#define CONFIG_STATUS_LED
-#define CONFIG_GPIO_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-#define STATUS_LED_BOOT 0
-#define STATUS_LED_BIT MX23_PAD_SSP1_DETECT__GPIO_2_1
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+#define CONFIG_STATUS_LED
+#define CONFIG_GPIO_LED
+#define CONFIG_BOARD_SPECIFIC_LED
+#define STATUS_LED_BOOT 0
+#define STATUS_LED_BIT MX23_PAD_SSP1_DETECT__GPIO_2_1
+#define STATUS_LED_STATE STATUS_LED_ON
+#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
/*
* MMC Driver
*/
-#ifdef CONFIG_CMD_MMC
+#ifdef CONFIG_CMD_MMC
#define CONFIG_MMC
#define CONFIG_BOUNCE_BUFFER
#define CONFIG_GENERIC_MMC
#define CONFIG_APBH_DMA
/* USB */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MXS
-#define CONFIG_EHCI_MXS_PORT0
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
-#define CONFIG_EHCI_IS_TDI
-#define CONFIG_USB_STORAGE
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MXS
+#define CONFIG_EHCI_MXS_PORT0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
#endif
/* Ethernet */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_SMSC95XX
+#ifdef CONFIG_CMD_NET
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_SMSC95XX
#endif
/*
* Boot Linux
*/
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_LOADADDR 0x42000000
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_OF_LIBFDT
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_LOADADDR 0x42000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_OF_LIBFDT
/*
* Environment
*/
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_ENV_OVERWRITE
-#ifdef CONFIG_ENV_IS_IN_MMC
-#define CONFIG_ENV_OFFSET (256 * 1024)
-#define CONFIG_ENV_SIZE (16 * 1024)
-#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OVERWRITE
+#ifdef CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET (256 * 1024)
+#define CONFIG_ENV_SIZE (16 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
#endif
/*
"else " \
"bootm; " \
"fi;\0" \
- "netargs=setenv bootargs console=${console_mainline},${baudrate} " \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
#define CONFIG_SYS_I2C_BASE IMX_I2C_BASE
#define CONFIG_SYS_I2C_SPEED 100000
+/* RTC */
+#define CONFIG_RTC_IMXDI
+#define CONFIG_CMD_DATE
+
/* Ethernet Configs */
#define CONFIG_CMD_PING
#ifndef __MX28EVK_CONFIG_H__
#define __MX28EVK_CONFIG_H__
-/*
- * SoC configurations
- */
+/* SoC configurations */
#define CONFIG_MX28 /* i.MX28 SoC */
#define CONFIG_MXS_GPIO /* GPIO control */
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_ARCH_MISC_INIT
-/*
- * SPL
- */
+/* SPL */
#define CONFIG_SPL
#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs"
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
-/*
- * U-Boot Commands
- */
+/* U-Boot Commands */
#include <config_cmd_default.h>
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_SPI
#define CONFIG_CMD_USB
#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NAND
-/*
- * Memory configurations
- */
+/* Memory configurations */
#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
#define PHYS_SDRAM_1 0x40000000 /* Base address */
#define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */
#define CONFIG_SYS_TEXT_BASE 0x40000100
#define CONFIG_ENV_OVERWRITE
-/*
- * U-Boot general configurations
- */
+/* U-Boot general configurations */
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_PROMPT "MX28EVK U-Boot > "
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
#define CONFIG_CMDLINE_EDITING /* Command history etc */
#define CONFIG_SYS_HUSH_PARSER
-/*
- * Serial Driver
- */
+/* Serial Driver */
#define CONFIG_PL011_SERIAL
#define CONFIG_PL011_CLOCK 24000000
#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE }
#define CONFIG_CONS_INDEX 0
#define CONFIG_BAUDRATE 115200 /* Default baud rate */
-/*
- * DMA
- */
+/* DMA */
#define CONFIG_APBH_DMA
-/*
- * MMC Driver
- */
-#define CONFIG_ENV_IS_IN_MMC
+/* MMC Driver */
#ifdef CONFIG_ENV_IS_IN_MMC
#define CONFIG_ENV_OFFSET (256 * 1024)
#define CONFIG_ENV_SIZE (16 * 1024)
#define CONFIG_MXS_MMC
#endif
-/*
- * NAND Driver
- */
+/* NAND Driver */
+#define CONFIG_ENV_SIZE (16 * 1024)
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_MXS
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x60000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+
+/* Environment is in NAND */
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+#define CONFIG_ENV_SECT_SIZE (128 * 1024)
+#define CONFIG_ENV_RANGE (512 * 1024)
+#ifndef CONFIG_ENV_OFFSET
+#define CONFIG_ENV_OFFSET 0x300000
#endif
+#define CONFIG_ENV_OFFSET_REDUND \
+ (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
-/*
- * Ethernet on SOC (FEC)
- */
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define MTDIDS_DEFAULT "nand0=gpmi-nand"
+#define MTDPARTS_DEFAULT \
+ "mtdparts=gpmi-nand:" \
+ "3m(bootloader)ro," \
+ "512k(environment)," \
+ "512k(redundant-environment)," \
+ "4m(kernel)," \
+ "128k(fdt)," \
+ "8m(ramdisk)," \
+ "-(filesystem)"
+#endif
+
+/* Ethernet on SOC (FEC) */
#ifdef CONFIG_CMD_NET
#define CONFIG_NET_MULTI
#define CONFIG_ETHPRIME "FEC0"
#define CONFIG_MX28_FEC_MAC_IN_OCOTP
#endif
-/*
- * RTC
- */
+/* RTC */
#ifdef CONFIG_CMD_DATE
#define CONFIG_RTC_MXS
#endif
-/*
- * USB
- */
+/* USB */
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MXS
#define CONFIG_SYS_I2C_SPEED 400000
#endif
-/*
- * SPI
- */
+/* SPI */
#ifdef CONFIG_CMD_SPI
#define CONFIG_HARD_SPI
#define CONFIG_MXS_SPI
#endif
#endif
-/*
- * Boot Linux
- */
+/* Boot Linux */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTDELAY 1
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_OF_LIBFDT
-/*
- * Extra Environments
- */
+/* Extra Environments */
#define CONFIG_EXTRA_ENV_SETTINGS \
"update_nand_full_filename=u-boot.nand\0" \
"update_nand_firmware_filename=u-boot.sb\0" \
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
#define CONFIG_MXC_GPIO
#define CONFIG_MXC_UART
/* Command definition */
#include <config_cmd_default.h>
+#define CONFIG_CMD_BMODE
#define CONFIG_CMD_BOOTZ
#undef CONFIG_CMD_IMLS
"fi;\0"
#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev};" \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"fi; " \
"else run netboot; fi"
-#define CONFIG_ARP_TIMEOUT 200UL
-
/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_HUSH_PARSER
--- /dev/null
+/*
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Wandboard.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+#include <asm/sizes.h>
+
+#define CONFIG_MX6
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define MACH_TYPE_WANDBOARD 4412
+#define CONFIG_MACH_TYPE MACH_TYPE_WANDBOARD
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (3 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+
+/* Command definition */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_BOOTDELAY 5
+
+#define CONFIG_SYS_MEMTEST_START 0x10000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
+#define CONFIG_LOADADDR 0x12000000
+#define CONFIG_SYS_TEXT_BASE 0x17800000
+
+/* MMC Configuration */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+/* Ethernet Configuration */
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 1
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
+#if defined(CONFIG_MX6DL)
+#define CONFIG_DEFAULT_FDT_FILE "imx6dl-wandboard.dtb"
+#elif defined(CONFIG_MX6S)
+#define CONFIG_DEFAULT_FDT_FILE "imx6s-wandboard.dtb"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "uimage=uImage\0" \
+ "console=ttymxc0\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+ "fdt_addr=0x11000000\0" \
+ "boot_fdt=try\0" \
+ "ip_dyn=yes\0" \
+ "mmcdev=0\0" \
+ "mmcpart=2\0" \
+ "mmcroot=/dev/mmcblk0p3 rootwait rw\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "bootm ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootm; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootm; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${uimage}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootm ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootm; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootm; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else run netboot; fi"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "=> "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE 256
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
+
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_SIZE (8 * 1024)
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMD_BOOTZ
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+#endif /* __CONFIG_H * */
struct fsl_esdhc_cfg {
u32 esdhc_base;
u32 sdhc_clk;
+ u8 max_bus_width;
};
/* Select the correct accessors depending on endianess */
projects / people / ms / u-boot.git / commitdiff
