arc: implement slave cores kick-start for Linux kernel
With new SMP-enabled CPUs with ARC HS38 cores and corresponding support
in Linux kernel it's required to add basic SMP support in U-Boot.
Currently we assume the one and only core starts execution after
power-on. So most of things in U-Boot is handled in UP mode.
But when U-Boot is used for loading and starting Linux kernel right
before jumping to kernel's entry point U-Boot:
[1] Sets all slave cores to jump to the same address [kernel's entry
point]
[2] Really starts all slav cores
In ARC's implemetation of SMP in Linux kernel all cores are supposed to
run the same start-up code. But only core with ID 0 (master core)
processes further while others are looping waiting for master core to
complete some initialization.
That means it's safe to un-pause slave cores and let them execute kernel
- they will wait for master anyway.
spi, sf: Use offset and size in sf cmd from mtdpartition
With this patch, it is possible to get the offset and size information
from the mtdpartiton setting in "mtdparts", similiar to the
"nand" commandos.
=> sf
sf - SPI flash sub-system
Usage:
sf probe [[bus:]cs] [hz] [mode] - init flash device on given SPI bus
and chip select
sf read addr offset|partition len - read `len' bytes starting at
`offset' to memory at `addr'
sf write addr offset|partition len - write `len' bytes from memory
at `addr' to flash at `offset'
sf erase offset|partition [+]len - erase `len' bytes from `offset'
`+len' round up `len' to block size
sf update addr offset|partition len - erase and write `len' bytes from memory
at `addr' to flash at `offset'
=>
for example "env" is defined in mtdparts:
=> sf read 13000000 env
device 0 offset 0xd0000, size 0x10000
SF: 65536 bytes @ 0xd0000 Read: OK
zynq-uboot> mtdparts add nor0 0x10000@0x0 env
zynq-uboot> sf erase env 0x10000
SF: 65536 bytes @ 0x0 Erased: OK
zynq-uboot> sf write 0x100 env
device 0 offset 0x0, size 0x10000
SF: 65536 bytes @ 0x0 Written: OK
zynq-uboot> sf read 0x40000 env
device 0 offset 0x0, size 0x10000
SF: 65536 bytes @ 0x0 Read: OK
Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Jagannadh Teki <jteki@openedev.com> Reviewed-by: Jagannadh Teki <jteki@openedev.com>
mtd, nand: Move common functions from cmd_nand.c to common place
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Scott Wood <scottwood@freescale.com> Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Changes from Heiko Schocher against this patch:
- Remove compile error if not defining CONFIG_SPI_FLASH_MTD:
LD drivers/mtd/spi/built-in.o
drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1
make: *** [drivers/mtd/spi] Fehler 2
- Add a README entry.
- Add correct writebufsize, to fit with Linux v3.14
MTD, UBI/UBIFS sync.
Note (From Jagan): For testing raw mtd parition erase/read/write operations
using cmd_sf, sf_mtd should be required to register the spi flash device to
MTD layer but the sf_mtd_info ops were not required until and unless if we
use any flash filesystem layer say for example UBI. Due to this the foot-print
got increased ~290bytes in non-UBI case here that should be acceptible.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Jagannadh Teki <jteki@openedev.com> Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Haikun Wang [Sat, 27 Jun 2015 16:21:05 +0000 (21:51 +0530)]
defconfig: ls1021a: Add OF_CONTROL and DM support
PI and QSPI only work when boot from QSPI on ls1021a.
This patch only enable options in qspi boot defconfig.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com> Tested-by: Haikun Wang <haikun.wang@freescale.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Haikun Wang [Fri, 26 Jun 2015 11:30:41 +0000 (19:30 +0800)]
dm: ls1021aqds: dts: Use "spi_dataflash" driver instead of "spi_flash_std" for DSPI flash
The type of DSPI flash on ls1021aqds is AT45DB021, it has specail
commands and page-size.
Use the special spi flash driver instead of "spi_flash_std" driver.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com> Tested-by: Haikun Wang <haikun.wang@freescale.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jteki@openedev.com>
Haikun Wang [Fri, 26 Jun 2015 11:30:27 +0000 (19:30 +0800)]
dm: sf: Add Atmel DataFlash spi flash driver
Atmel DataFlash chips have commands different from common spi
flash commands.
Atmel DataFlash also have special page-size.
This driver add support for accessing Atmel DataFlash.
It is based on the Driver Model.
Example:
=> sf probe 1:0
SPI DataFlash: Detected AT45DB021B with page size 264 Bytes, erase size 264 Bytes, total 264 KiB, revision d
=> sf erase 0 42000
SF: 270336 bytes @ 0x0 Erased: OK
=> mw.l 8200000045444342 20000
=> sf write 82000000 0 42000
SF: 270336 bytes @ 0x0 Written: OK
=> sf read 83000000 0 42000
SF: 270336 bytes @ 0x0 Read: OK
=> cmp.b 8200000083000000 42000
Total of 270336 byte(s) were the same
Signed-off-by: Haikun Wang <haikun.wang@freescale.com> Tested-by: Haikun Wang <haikun.wang@freescale.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Chakra Divi <cdivi@openedev.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Kevin Smith [Mon, 18 May 2015 16:09:46 +0000 (16:09 +0000)]
db-88f6820-gp.h: Load data blobs into lower memory
By default on this platform, u-boot loads data into high memory
in the range of 0x7Fxxxxxx, which generates a data abort when the
kernel tries to read it. Config the u-boot environment to load
the device tree and initrd image into lower memory to make them
accessible to the kernel.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Stefan Roese <sr@denx.de>
Joe Hershberger [Mon, 22 Jun 2015 21:15:29 +0000 (16:15 -0500)]
Move default y configs out of arch/board Kconfig
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM] Signed-off-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Fri, 19 Jun 2015 21:39:41 +0000 (23:39 +0200)]
mmc: bcm2835_sdhci: Restore original delay behavior
Patch 33fe2fb8df01647f97a7bce96a1c7781a7f6d253 titled
"mmc: bcm283x: Remove get_timer_us() from mmc driver"
incorrectly replaced ad-hoc get_timer_us() function
with a plain get_timer(). The get_timer() operates in
mSec units instead of uSec though, which caused very
slow operation of the driver.
Restore the original behavior of the driver, but avoid
get_timer_us() and use timer_get_us() instead. The later
is part of the standard API.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jakub Kiciński <moorray3@wp.pl> Cc: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Jakub Kicinski <kubakici@wp.pl>
Chris Packham [Fri, 19 Jun 2015 08:25:59 +0000 (20:25 +1200)]
README: Describe CONFIG_SYS_NO_FLASH
Unlike most configuration options defining this actually disables
support for a feature (parallel flash). Eventually the logic behind this
should probably be flipped so that '#ifndef CONFIG_SYS_NO_FLASH' becomes
'#ifdef CONFIG_HAS_PARALLEL_FLASH' but for now lets document the
existing behaviour.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Mugunthan V N [Tue, 16 Jun 2015 14:53:39 +0000 (20:23 +0530)]
am43xx_evm: add eth boot support
add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falcon mode and
environment on MMC is defined for ethernet boot mode
environment should be set to nowhere.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Mugunthan V N [Tue, 16 Jun 2015 14:53:38 +0000 (20:23 +0530)]
am43xx_evm: add usb host boot support
While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config target which sets SPL_TEXT_BASE to OCMC ram.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 16 Jun 2015 14:53:37 +0000 (20:23 +0530)]
am43xx: Update CONFIG_SPL_TEXT_BASE
With 1.2 silicon this is now the documented starting usable point for
downloading images to (and corrects a problem with peripheral booting
with prior silicon). Prior silicon is OK using this address as well.
Signed-off-by: Tom Rini <trini@konsulko.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Nishanth Menon [Tue, 16 Jun 2015 13:29:01 +0000 (08:29 -0500)]
ARM: DRA7: Change configuration to prevent DDR reset control from EMIF
DRA7/AM57xx devices can be operated in many different configurations.
When the SoC is supposed to support a configuration where low power mode
state may involve the SoC completely powered off and DDR is in self
refresh, SoC EMIF controller should not be the master of the reset
signal and an external entity might be in control of things.
The default configuration of Linux on TI evms involve not powering off
the voltage rails (due to various reasons including reliability concerns)
and must not allow DDR reset to be controlled by EMIF. On platforms
where external entity might control the reset signal, this configuration
will be a "dont care".
Heiko Schocher [Tue, 16 Jun 2015 12:59:34 +0000 (14:59 +0200)]
arm, am33xx: update for siemens am335x based boards
updates for the siemens am335x based boards:
- draco: add delay for DDR3 configuration
- change MTD partition layout and add a possibility
to redefine MTD layout in board header.
- move ubi support to common header file
- draco: improve dtb naming
- draco: set CONFIG_SYS_CBSIZE to 1024
- add generic env based led
Leds can now be defined in Environment
- add generic env based dfu button
Which gpio is used for the dfu button can be defined
through the Environment
- set MACH_TYPE only if defined
- draco: increase CPU freq to 300MHz
- Add time command to siemens am33xx boards
- DDR3: increase default tRFC
- draco: enable pullup for DFU and ERST pin
- change print format DDR3
Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Acked-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Heiko Schocher <hs@denx.de>
common: cmd_part: start and size sub-commands introduction
This introduces the part start and part size sub-commands. The purpose of these
is to store the start block and size of a partition in a variable, given the
device and partition number.
This allows reading raw data that fits a single partition more easily.
For instance, this could be used to figure out the start block and size of a
kernel partition when a partition table is present, given the partition number.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Stephen Warren <swarren@nvidia.com>
[trini: Change "%lx" to LBAF] Signed-off-by: Tom Rini <trini@konsulko.com>
Hans de Goede [Thu, 18 Jun 2015 20:34:34 +0000 (22:34 +0200)]
usb: kbd: Disable idle input reports when we do not need them
When we're polling and thus handling key-repeat in software, make sure
to disable idle reports, some keyboards may have these enabled by default
messing up our software keyrepeat.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Thu, 18 Jun 2015 20:34:33 +0000 (22:34 +0200)]
usb: ehci: Properly deal with data toggle for interrupt endpoints
Without this we loose every other interrupt packet. We never noticed this
because with keyboards the packets which we were loosing would normally
be key release packets.
But now that we do keyrepeat in software instead of relying on the hid
idle functionality, missing a release will result in key repeat triggering.
This commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Wed, 10 Jun 2015 15:04:04 +0000 (17:04 +0200)]
usb.h: Always declare usb function prototypes
There is no harm in declaring the function prototypes even if nothing
implements them, and when CONFIG_DM_USB=y the various usb functions are
available regardless of any controller drivers being enabled.
This fixes compile warnings due to missing prototypes on ARCHs where
the ARCH Kconfig always enables CONFIG_DM_USB and various usb drivers.
One could argue that in the case of no controllers CONFIG_DM_USB should not
be set, but this problem is typically seen during bringup of boards which
do actually have usb controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This allows using only one of either raw or fs mode for SPL mmc boot, without
the need to have provisions for the other. In particular, a device may have
U-Boot installed on a file system on the mmc, without ever needing to read
U-Boot from raw memory. Thus, there is no reason to provide a sector or
partition for raw mode. This allows this behaviour and still provides a robust
fallback mechanism in case provisions for both modes are defined.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Peter Robinson [Wed, 17 Jun 2015 15:58:32 +0000 (16:58 +0100)]
tools/env/fw_env.h: Correct include order
When building tools-only (or env) we need to be sure that we do use
<linux/kconfig.h> and do not use <generated/autoconf.h>. This will fix
problems such as running 'make defconfig' or 'make sandbox_config' and
then 'make tools-only'.
Based on the responses below to the thread add linux/kconfig.h higher in
the includes and drop the now unneeded autoconf.h lower down to ensure
the default environment is included correctly
Tom Rini [Fri, 12 Jun 2015 00:53:31 +0000 (20:53 -0400)]
mmc_write.c: Make mmc_berase do 32bit safe 64bit math
We want to see if the requested start or total block count are
unaligned. We discard the whole numbers and only care about the
remainder. Update the code to use div_u64_rem here and add a comment.
Cc: Hans de Goede <hdegoede@redhat.com> Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Cc: Bernhard Nortmann <bernhard.nortmann@web.de> Reported-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Bernhard Nortmann <bernhard.nortmann@web.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com>
ti: am335x/am437x/omap5 devices: Fix breakage when CONFIG_CMD_NET is not used
Currently there is no default value for NETARGS if CONFIG_CMD_NET=y isn't set.
This results in build errors which was first discovered when trying to run
make env.
By defining a blank NETARGS these errors can be avoided.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Tested-by: Maxin B. John <maxin.john@enea.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Jeroen Hofstee [Sat, 30 May 2015 08:11:24 +0000 (10:11 +0200)]
mtd: OMAP: Enable GPMC prefetch mode for 16 bit access
commit c316f57 "mtd: OMAP: Enable GPMC prefetch mode" only enabled
prefetch mode for 8 bit nand access, this adds 16 bit as well.
Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@konsulko.com> Cc: Daniel Mack <zonque@gmail.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Tom Rini <trini@konsulko.com>
Jeroen Hofstee [Sat, 30 May 2015 08:11:23 +0000 (10:11 +0200)]
omap_gpmc: move prefetch out of CONFIG_NAND_OMAP_ELM
The prefech mode is a feature of the gpmc, not the ELM. An am3517
does not have an elm, but can do prefeches, so move the code out
of the CONFIG_NAND_OMAP_ELM ifdef.
Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@konsulko.com> Cc: Daniel Mack <zonque@gmail.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Tom Rini <trini@konsulko.com>
Karsten Merker [Sun, 14 Jun 2015 10:08:42 +0000 (12:08 +0200)]
MSI_Primo81_defconfig: enable USB OTG port and keyboard support
The MSI Primo 81 is an Allwinner A31s-based tablet on which the
OTG port is the only accessible USB interface. The existing
defconfig had VGA console on the LCD enabled, but was missing
keyboard support because the prerequisites for that (sunxi MUSB
support and AXP221 GPIO support) had not been available before.
All previously missing dependencies are available now, so this
patch enables keyboard support and its prerequisites in the
defconfig.
Signed-off-by: Karsten Merker <merker@debian.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 14 Jun 2015 14:53:15 +0000 (16:53 +0200)]
sun6i: cpu_reset: Do not return from cpu_reset()
Currently on sun6i after a "reset" the prompt returns and the user can
even type stuff until the watchdog triggers and does the actual reset.
This is somewhat unexpected behavior for the "reset" command, this
commit adds an endless loop to wait for the watchdog to trigger so that
we do not return to the prompt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 14 Jun 2015 09:58:43 +0000 (11:58 +0200)]
sunxi: musb: Remove unused sunxi_musb_exit method
Remove the unused sunxi_musb_exit method, there is no code in u-boot
calling the exit method, and our implementation was broken as it did
not disable the clocks and asserted reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 14 Jun 2015 09:55:28 +0000 (11:55 +0200)]
sunxi: musb: Do not fully reset the controler from sunxi_musb_disable
Fully resetting the controller is a too big hammer, and the musb_core will
then afterwards fail to communicate with any endpoints other then 0 as
too much state was cleared.
Instead report vbus low for 200ms which will effectively end the current
session without needing to do a full reset.
This fixes usb mass-storage devices no longer working after a "usb reset"
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tom Rini [Sat, 13 Jun 2015 00:52:29 +0000 (20:52 -0400)]
omap5: Exclude more environment from SPL builds
In the cases where we make use of environment in SPL we do not need
these defaults compiled in and available. These are taking up space
that in some cases now prevent linking, so drop.
Lokesh Vutla [Thu, 4 Jun 2015 04:38:50 +0000 (10:08 +0530)]
ARM: DRA7: emif: Fix DDR init sequence during warm reset
Unlike OMAP5, EMIF PHY used in DRA7 will be left in unknown state after
warm reset, emif needs to be configured to bring it back to a known
state. So configure EMIF during warm reset.
Reported-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Wed, 10 Jun 2015 10:24:50 +0000 (15:54 +0530)]
ARM: AM43x: Fix MAX_RAM_BANK_SIZE
On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in
AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf.
But MAX_RAM_BANK_SIZE is defined as 1GB.
Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx.
Tom Rini [Fri, 5 Jun 2015 10:21:11 +0000 (15:51 +0530)]
am33xx: Re-enable SW levelling for DDR2
The recent changes for hw leveling on am33xx were not intended for
DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config
value to check against. This lets us pass in the value we would use to
configure, when we have not yet configured the board yet. In other cases
update the call to be as functional as before and check an already
programmed value in.
Tested-by: Yan Liu <yan-liu@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Roger Quadros [Fri, 5 Jun 2015 09:42:21 +0000 (12:42 +0300)]
am335x_evm: nand: Fix boot from NAND
Use the correct partition names from with the Device Tree blob
and the kernel is picked up. Also use partition name instead of
number for the root filesystem in the kernel boot arguments.
Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Roger Quadros [Fri, 5 Jun 2015 09:42:20 +0000 (12:42 +0300)]
am335x_evm: am44xx_evm: dra7xx_evm: nand: Fix file-system partition name
We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume within the
single NAND partition. The last NAND partition is therefore more
appropriately named as "NAND.file-system" instead of "NAND.rootfs"
The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the
last NAND partition. This patch makes the partition name consistent
between u-boot and the kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Mark Langsdorf [Thu, 4 Jun 2015 23:58:49 +0000 (00:58 +0100)]
highbank: add custom ahci_link_up function
The Calxeda highbank SOC needs a custom sequence to bring up SATA links,
so override ahci_link_up with custom function to handle combophy setup.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com> Signed-off-by: Richard Gibbs Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Andre Przywara <osp@andrep.de>
Stefan Roese [Fri, 29 May 2015 11:25:04 +0000 (13:25 +0200)]
tools/kwboot: Add parameters to set delay and timeout via cmdline
To support the Armada 38x, new values for the request-delay and the
response-timeout are needed. As the values already implemented in
this tool (for Kirkwood and Armada XP) don't seem to work here.
To make this more flexible, lets add make those 2 parameters
configurable via the cmdline. Here the new parameters:
-q <req-delay>: use specific request-delay
-s <resp-timeo>: use specific response-timeout
For the Marvell DB-88F6820 these values are known to work:
One board:
-q 2 -s 1
2nd board:
-q 5 -s 5
So this seems to be even board specific. But with this patch now
those values can be specified and tested via the cmdline.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Kevin Smith <kevin.smith@elecsyscorp.com> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Luka Perkov <luka.perkov@sartura.hr>
Kevin Smith [Mon, 18 May 2015 16:09:44 +0000 (16:09 +0000)]
arm: mvebu: Update CBAR with SOC regs base
SMP-enabled Linux kernels read the CBAR register in CP15 to find
the address of the SCU registers. After remapping internal
registers, also update the CBAR so the kernel can find them.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Stefan Roese <sr@denx.de>
Kevin Smith [Mon, 16 Mar 2015 14:58:21 +0000 (14:58 +0000)]
tools/kwbimage.c: Correct header size for SPI boot
If defined, the macro CONFIG_SYS_SPI_U_BOOT_OFFS allows a board
to specify the offset of the payload image into the kwb image
file. This value was being used to locate the image, but was not
used in the "header size" field of the main header. Move the
use of this macro into the function that returns the header size
so that the same value is used in all places.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Tested-by: Stefan Roese <sr@denx.de>
Mark Langsdorf [Thu, 4 Jun 2015 23:58:46 +0000 (00:58 +0100)]
ahci: extend data io wait to 10s
The AHCI driver currently waits 5s before timing out when sending a
data command to a drive. Some drives take upwards of 8s to respond to
the initial data command while they're spinning up. Increase the
data io timeout to 10s so that those drives can be found on initial
scsi scan.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com> Signed-off-by: Andre Przywara <osp@andrep.de>
Mark Langsdorf [Thu, 4 Jun 2015 23:58:45 +0000 (00:58 +0100)]
ahci: support LBA48 data reads for 2+TB drives
Enable full 48-bit LBA48 data reads by passing the upper word of the
LBA block pointer in bytes 9 and 10 of the FIS.
This allows uboot to load data from any arbitrary sector on a drive
with 2 or more TB of available data connected to an AHCI controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com> Signed-off-by: Andre Przywara <osp@andrep.de>
[trini: Make use of CONFIG_SYS_64BIT_LBA in a few places to drop
warnings on platforms that don't enable that feature ] Signed-off-by: Tom Rini <trini@konsulko.com>
Mark Langsdorf [Thu, 4 Jun 2015 23:58:43 +0000 (00:58 +0100)]
ARM: highbank: add reset support for Calxeda Midway machine
The Calxeda Midway part has A15 cores, which do not have the Highbank
A9's SCU used there for resetting the chip.
Add code to distinguish between the A9 and the A15 and invoke the
appropriate register writes to support the newer part.
Andre: rework detection of Highbank vs. Midway
Rob: fix Andre's reworked detection
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com> Signed-off-by: Andre Przywara <osp@andrep.de> Signed-off-by: Rob Herring <robh@kernel.org>
Enabling IO delay recalibration sequence for DRA7 EVM.
UART and I2C are configured before IO delay recalibration sequence
as these are used earlier and safe to use.
Lokesh Vutla [Thu, 4 Jun 2015 11:12:37 +0000 (16:42 +0530)]
ARM: DRA7: Add support for manual mode configuration
In addition to the regular mux configuration, certain pins of DRA7
require to have "manual mode" also programmed, when predefined
delay characteristics cannot be used for the interface.
struct iodelay_cfg_entry is introduced for populating
manual mode IO timings.
For configuring manual mode, along with the normal pad
configuration do the following steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1(Enable MANUAL_MODE macro along with mux)
- Populate A_DELAY, G_DELAY values that are specified in DATA MANUAL.
And pass the offset of the CFG_XXX register in iodelay_cfg_entry.
Lokesh Vutla [Thu, 4 Jun 2015 11:12:36 +0000 (16:42 +0530)]
ARM: DRA7: Add support for IO delay configuration
On DRA7, in addition to the regular muxing of pins, an additional
hardware module called IODelay which is also expected to be
configured. This "IODelay" module has it's own register space that is
independent of the control module.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay recalibration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do muxing as part of IOdelay recalibration.
IODELAY recalibration sequence:
- Complete AVS voltage change on VDD_CORE_L
- Unlock IODLAY config registers.
- Perform IO delay calibration with predefined values.
- Isolate all the IOs
- Update the delay mechanism for each IO with new calibrated values.
- Configure PAD configuration registers
- De-isolate all the IOs.
- Relock IODELAY config registers.
Lokesh Vutla [Thu, 4 Jun 2015 11:12:35 +0000 (16:42 +0530)]
ARM: DRA7: Add support for virtual mode configuration
In addition to the regular mux configuration, certain pins of DRA7
require to have "virtual mode" also programmed.
This allows for predefined delay characteristics to be used by the SoC
to meet timing characterstics needed for the interface.
Provide easy to use macro to do the same.
For configuring virtual mode, along with normal pad configuration add
the following two steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1
- DELAYMODE filed should be configured with value given in DATA Manual.
CTRL_CORE_PAD_XXX[7:4]:DELAYMODE =[0-15] (as given in DATA manual).
Lokesh Vutla [Thu, 4 Jun 2015 11:12:34 +0000 (16:42 +0530)]
ARM: DRA7: Add pinctrl register definitions
Adopting the pinctrl register definitions from Linux kernel
to be consistent.
Old definitions will be removed once all the pinctrl data
is adapted to new definitions.
Lokesh Vutla [Wed, 3 Jun 2015 11:27:47 +0000 (16:57 +0530)]
ARM: DRA7xx: EMIF: Fix DLL_CALIB_CTRL register
When DLL_CALIB_INTERVAL is set, an extra delay is added
which is not required and it consumes EMIF bandwidth.
So making the DLL_CALIB_CTRL[8:0]DLL_CALIB_INTERVAL bits to 0.
Masahiro Yamada [Wed, 27 May 2015 02:39:22 +0000 (11:39 +0900)]
kconfiglib: sync with the latest in Kconfiglib project
This commit imports some updates of kconfiglib.py from
https://github.com/ulfalizer/Kconfiglib
- Warn about and ignore the "allnoconfig_y" Kconfig option
- Statements in choices inherit menu/if deps
- Add Symbol.is_allnoconfig_y()
- Hint that modules are still supported despite warnings.
- Add warning related to get_defconfig_filename().
- Fix typo in docs.
- Allow digits in $-references to symbols.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com> Signed-off-by: Philip Craig <philipjcraig@gmail.com> Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Pali Rohár [Tue, 9 Jun 2015 17:05:00 +0000 (19:05 +0200)]
Nokia RX-51: Fix calculating return address in save_boot_params
Commit e11c6c279d823dc0d2f470c5c2e3c0a9854a640f broke calculating lr register
in function save_boot_params() and caused U-Boot to crash at early boot time
on Nokia N900 board.
This patch fix calculating return address in lr register and make Nokia N900
board bootable again. Patch was tested in qemu and also on real N900 HW.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
projects / people / ms / u-boot.git / log
