struct hostapd_wmm_rule wmm_rules[WMM_AC_NUM];
};
+#define HE_MAC_CAPAB_0 0
#define HE_MAX_MAC_CAPAB_SIZE 6
#define HE_MAX_PHY_CAPAB_SIZE 11
#define HE_MAX_MCS_CAPAB_SIZE 12
*/
u8 p2p_go_ctwindow;
- /**
- * smps_mode - SMPS mode
- *
- * SMPS mode to be used by the AP, specified as the relevant bits of
- * ht_capab (i.e. HT_CAP_INFO_SMPS_*).
- */
- unsigned int smps_mode;
-
/**
* disable_dgaf - Whether group-addressed frames are disabled
*/
* he_spr_srg_obss_pd_max_offset - Maximum TX power offset
*/
int he_spr_srg_obss_pd_max_offset;
+
+ /**
+ * twt_responder - Whether Target Wait Time responder is enabled
+ */
+ int twt_responder;
};
struct wpa_driver_mesh_bss_params {
unsigned int flags;
};
+struct wpa_driver_set_key_params {
+ /**
+ * ifname - Interface name (for multi-SSID/VLAN support) */
+ const char *ifname;
+
+ /**
+ * alg - Encryption algorithm
+ *
+ * (%WPA_ALG_NONE, %WPA_ALG_WEP, %WPA_ALG_TKIP, %WPA_ALG_CCMP,
+ * %WPA_ALG_IGTK, %WPA_ALG_PMK, %WPA_ALG_GCMP, %WPA_ALG_GCMP_256,
+ * %WPA_ALG_CCMP_256, %WPA_ALG_BIP_GMAC_128, %WPA_ALG_BIP_GMAC_256,
+ * %WPA_ALG_BIP_CMAC_256);
+ * %WPA_ALG_NONE clears the key. */
+ enum wpa_alg alg;
+
+ /**
+ * addr - Address of the peer STA
+ *
+ * (BSSID of the current AP when setting pairwise key in station mode),
+ * ff:ff:ff:ff:ff:ff for broadcast keys, %NULL for default keys that
+ * are used both for broadcast and unicast; when clearing keys, %NULL
+ * is used to indicate that both the broadcast-only and default key of
+ * the specified key index is to be cleared */
+ const u8 *addr;
+
+ /**
+ * key_idx - Key index
+ *
+ * (0..3), usually 0 for unicast keys; 0..4095 for IGTK */
+ int key_idx;
+
+ /**
+ * set_tx - Configure this key as the default Tx key
+ *
+ * Only used when driver does not support separate unicast/individual
+ * key */
+ int set_tx;
+
+ /**
+ * seq - Sequence number/packet number
+ *
+ * seq_len octets, the next packet number to be used for in replay
+ * protection; configured for Rx keys (in most cases, this is only used
+ * with broadcast keys and set to zero for unicast keys); %NULL if not
+ * set */
+ const u8 *seq;
+
+ /**
+ * seq_len - Length of the seq, depends on the algorithm
+ *
+ * TKIP: 6 octets, CCMP/GCMP: 6 octets, IGTK: 6 octets */
+ size_t seq_len;
+
+ /**
+ * key - Key buffer
+ *
+ * TKIP: 16-byte temporal key, 8-byte Tx Mic key, 8-byte Rx Mic Key */
+ const u8 *key;
+
+ /**
+ * key_len - Length of the key buffer in octets
+ *
+ * WEP: 5 or 13, TKIP: 32, CCMP/GCMP: 16, IGTK: 16 */
+ size_t key_len;
+
+ /**
+ * vlan_id - VLAN index (0..4095) for VLAN offload cases */
+ int vlan_id;
+
+ /**
+ * key_flag - Additional key flags
+ *
+ * %KEY_FLAG_MODIFY
+ * Set when an already installed key must be updated.
+ * So far the only use-case is changing RX/TX status of
+ * installed keys. Must not be set when deleting a key.
+ * %KEY_FLAG_DEFAULT
+ * Set when the key is also a default key. Must not be set when
+ * deleting a key.
+ * %KEY_FLAG_RX
+ * The key is valid for RX. Must not be set when deleting a key.
+ * %KEY_FLAG_TX
+ * The key is valid for TX. Must not be set when deleting a key.
+ * %KEY_FLAG_GROUP
+ * The key is a broadcast or group key.
+ * %KEY_FLAG_PAIRWISE
+ * The key is a pairwise key.
+ * %KEY_FLAG_PMK
+ * The key is a Pairwise Master Key (PMK).
+ *
+ * Valid and pre-defined combinations are:
+ * %KEY_FLAG_GROUP_RX_TX
+ * WEP key not to be installed as default key.
+ * %KEY_FLAG_GROUP_RX_TX_DEFAULT
+ * Default WEP or WPA-NONE key.
+ * %KEY_FLAG_GROUP_RX
+ * GTK key valid for RX only.
+ * %KEY_FLAG_GROUP_TX_DEFAULT
+ * GTK key valid for TX only, immediately taking over TX.
+ * %KEY_FLAG_PAIRWISE_RX_TX
+ * Pairwise key immediately becoming the active pairwise key.
+ * %KEY_FLAG_PAIRWISE_RX
+ * Pairwise key not yet valid for TX. (Only usable when Extended
+ * Key ID is supported by the driver.)
+ * %KEY_FLAG_PAIRWISE_RX_TX_MODIFY
+ * Enable TX for a pairwise key installed with
+ * KEY_FLAG_PAIRWISE_RX.
+ *
+ * Not a valid standalone key type but pre-defined to be combined
+ * with other key_flags:
+ * %KEY_FLAG_RX_TX
+ * RX/TX key. */
+ enum key_flag key_flag;
+};
+
/**
* struct wpa_driver_capa - Driver capability information
*/
#define WPA_DRIVER_FLAGS_FTM_RESPONDER 0x0100000000000000ULL
/** Driver support 4-way handshake offload for WPA-Personal */
#define WPA_DRIVER_FLAGS_4WAY_HANDSHAKE_PSK 0x0200000000000000ULL
+/** Driver supports a separate control port for EAPOL frames */
+#define WPA_DRIVER_FLAGS_CONTROL_PORT 0x0400000000000000ULL
+/** Driver supports VLAN offload */
+#define WPA_DRIVER_FLAGS_VLAN_OFFLOAD 0x0800000000000000ULL
+/** Driver supports UPDATE_FT_IES command */
+#define WPA_DRIVER_FLAGS_UPDATE_FT_IES 0x1000000000000000ULL
u64 flags;
#define FULL_AP_CLIENT_STATE_SUPP(drv_flags) \
(drv_flags & WPA_DRIVER_FLAGS_FULL_AP_CLIENT_STATE)
-#define WPA_DRIVER_SMPS_MODE_STATIC 0x00000001
-#define WPA_DRIVER_SMPS_MODE_DYNAMIC 0x00000002
- unsigned int smps_modes;
-
unsigned int wmm_ac_supported:1;
unsigned int mac_addr_rand_scan_supported:1;
/* Configured ACS channel width */
u16 ch_width;
- /* ACS channel list info */
- unsigned int ch_list_len;
- const u8 *ch_list;
+ /* ACS frequency list info */
const int *freq_list;
};
/**
* set_key - Configure encryption key
- * @ifname: Interface name (for multi-SSID/VLAN support)
* @priv: private driver interface data
- * @alg: encryption algorithm (%WPA_ALG_NONE, %WPA_ALG_WEP,
- * %WPA_ALG_TKIP, %WPA_ALG_CCMP, %WPA_ALG_IGTK, %WPA_ALG_PMK,
- * %WPA_ALG_GCMP, %WPA_ALG_GCMP_256, %WPA_ALG_CCMP_256,
- * %WPA_ALG_BIP_GMAC_128, %WPA_ALG_BIP_GMAC_256,
- * %WPA_ALG_BIP_CMAC_256);
- * %WPA_ALG_NONE clears the key.
- * @addr: Address of the peer STA (BSSID of the current AP when setting
- * pairwise key in station mode), ff:ff:ff:ff:ff:ff for
- * broadcast keys, %NULL for default keys that are used both for
- * broadcast and unicast; when clearing keys, %NULL is used to
- * indicate that both the broadcast-only and default key of the
- * specified key index is to be cleared
- * @key_idx: key index (0..3), usually 0 for unicast keys; 0..4095 for
- * IGTK
- * @set_tx: configure this key as the default Tx key (only used when
- * driver does not support separate unicast/individual key
- * @seq: sequence number/packet number, seq_len octets, the next
- * packet number to be used for in replay protection; configured
- * for Rx keys (in most cases, this is only used with broadcast
- * keys and set to zero for unicast keys); %NULL if not set
- * @seq_len: length of the seq, depends on the algorithm:
- * TKIP: 6 octets, CCMP/GCMP: 6 octets, IGTK: 6 octets
- * @key: key buffer; TKIP: 16-byte temporal key, 8-byte Tx Mic key,
- * 8-byte Rx Mic Key
- * @key_len: length of the key buffer in octets (WEP: 5 or 13,
- * TKIP: 32, CCMP/GCMP: 16, IGTK: 16)
- *
+ * @params: Key parameters
* Returns: 0 on success, -1 on failure
*
* Configure the given key for the kernel driver. If the driver
* in driver_*.c set_key() implementation, see driver_ndis.c for an
* example on how this can be done.
*/
- int (*set_key)(const char *ifname, void *priv, enum wpa_alg alg,
- const u8 *addr, int key_idx, int set_tx,
- const u8 *seq, size_t seq_len,
- const u8 *key, size_t key_len);
+ int (*set_key)(void *priv, struct wpa_driver_set_key_params *params);
/**
* init - Initialize driver interface
* driver decide
* @csa_offs: Array of CSA offsets or %NULL
* @csa_offs_len: Number of elements in csa_offs
+ * @no_encrypt: Do not encrypt frame even if appropriate key exists
+ * (used only for testing purposes)
* Returns: 0 on success, -1 on failure
*/
int (*send_mlme)(void *priv, const u8 *data, size_t data_len,
int noack, unsigned int freq, const u16 *csa_offs,
- size_t csa_offs_len);
+ size_t csa_offs_len, int no_encrypt);
/**
* update_ft_ies - Update FT (IEEE 802.11r) IEs
int (*read_sta_data)(void *priv, struct hostap_sta_driver_data *data,
const u8 *addr);
+ /**
+ * tx_control_port - Send a frame over the 802.1X controlled port
+ * @priv: Private driver interface data
+ * @dest: Destination MAC address
+ * @proto: Ethertype in host byte order
+ * @buf: Frame payload starting from IEEE 802.1X header
+ * @len: Frame payload length
+ * @no_encrypt: Do not encrypt frame
+ *
+ * Returns 0 on success, else an error
+ *
+ * This is like a normal Ethernet send except that the driver is aware
+ * (by other means than the Ethertype) that this frame is special,
+ * and more importantly it gains an ordering between the transmission of
+ * the frame and other driver management operations such as key
+ * installations. This can be used to work around known limitations in
+ * IEEE 802.11 protocols such as race conditions between rekeying 4-way
+ * handshake message 4/4 and a PTK being overwritten.
+ *
+ * This function is only used for a given interface if the driver
+ * instance reports WPA_DRIVER_FLAGS_CONTROL_PORT capability. Otherwise,
+ * API users will fall back to sending the frame via a normal socket.
+ */
+ int (*tx_control_port)(void *priv, const u8 *dest,
+ u16 proto, const u8 *buf, size_t len,
+ int no_encrypt);
+
/**
* hapd_send_eapol - Send an EAPOL packet (AP only)
* @priv: private driver interface data
*/
int (*commit)(void *priv);
- /**
- * send_ether - Send an ethernet packet (AP only)
- * @priv: private driver interface data
- * @dst: Destination MAC address
- * @src: Source MAC address
- * @proto: Ethertype
- * @data: EAPOL packet starting with IEEE 802.1X header
- * @data_len: Length of the EAPOL packet in octets
- * Returns: 0 on success, -1 on failure
- */
- int (*send_ether)(void *priv, const u8 *dst, const u8 *src, u16 proto,
- const u8 *data, size_t data_len);
-
/**
* set_radius_acl_auth - Notification of RADIUS ACL change
* @priv: Private driver interface data
*/
int (*signal_monitor)(void *priv, int threshold, int hysteresis);
- /**
- * send_frame - Send IEEE 802.11 frame (testing use only)
- * @priv: Private driver interface data
- * @data: IEEE 802.11 frame with IEEE 802.11 header
- * @data_len: Size of the frame
- * @encrypt: Whether to encrypt the frame (if keys are set)
- * Returns: 0 on success, -1 on failure
- *
- * This function is only used for debugging purposes and is not
- * required to be implemented for normal operations.
- */
- int (*send_frame)(void *priv, const u8 *data, size_t data_len,
- int encrypt);
-
/**
* get_noa - Get current Notice of Absence attribute payload
* @priv: Private driver interface data
int (*br_set_net_param)(void *priv, enum drv_br_net_param param,
unsigned int val);
+ /**
+ * get_wowlan - Get wake-on-wireless status
+ * @priv: Private driver interface data
+ */
+ int (*get_wowlan)(void *priv);
+
/**
* set_wowlan - Set wake-on-wireless triggers
* @priv: Private driver interface data
/**
* struct acs_selected_channels - Data for EVENT_ACS_CHANNEL_SELECTED
- * @pri_channel: Selected primary channel
- * @sec_channel: Selected secondary channel
+ * @pri_freq: Selected primary frequency
+ * @sec_freq: Selected secondary frequency
* @vht_seg0_center_ch: VHT mode Segment0 center channel
+ * The value is the index of the channel center frequency for
+ * 20 MHz, 40 MHz, and 80 MHz channels. The value is the center
+ * frequency index of the primary 80 MHz segment for 160 MHz and
+ * 80+80 MHz channels.
* @vht_seg1_center_ch: VHT mode Segment1 center channel
+ * The value is zero for 20 MHz, 40 MHz, and 80 MHz channels. The
+ * value is the index of the channel center frequency for 160 MHz
+ * channels and the center frequency index of the secondary 80 MHz
+ * segment for 80+80 MHz channels.
* @ch_width: Selected Channel width by driver. Driver may choose to
* change hostapd configured ACS channel width due driver internal
* channel restrictions.
* hw_mode: Selected band (used with hw_mode=any)
*/
struct acs_selected_channels {
- u8 pri_channel;
- u8 sec_channel;
+ unsigned int pri_freq;
+ unsigned int sec_freq;
u8 vht_seg0_center_ch;
u8 vht_seg1_center_ch;
u16 ch_width;
projects / thirdparty / hostap.git / blobdiff