Eran Ben Elisha [Thu, 1 Aug 2019 11:27:30 +0000 (14:27 +0300)]
net/mlx5e: Fix compatibility issue with ethtool flash device
Cited patch deleted ethtool flash device support, as ethtool core can
fallback into devlink flash callback. However, this is supported only if
there is a devlink port registered over the corresponding netdevice.
As mlx5e do not have devlink port support over native netdevice, it broke
the ability to flash device via ethtool.
This patch re-add the ethtool callback to avoid user functionality breakage
when trying to flash device via ethtool.
Fixes: 9c8bca2637b8 ("mlx5: Move firmware flash implementation to devlink") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
net/mlx5e: Fix a race with XSKICOSQ in XSK wakeup flow
Add a missing spinlock around XSKICOSQ usage at the activation stage,
because there is a race between a configuration change and the
application calling sendto().
When running tcp_fastopen_backup_key.sh the following issue was seen in
a busybox environment.
./tcp_fastopen_backup_key.sh: line 33: [: -ne: unary operator expected
Shellcheck showed the following issue.
$ shellcheck tools/testing/selftests/net/tcp_fastopen_backup_key.sh
In tools/testing/selftests/net/tcp_fastopen_backup_key.sh line 33:
if [ $val -ne 0 ]; then
^-- SC2086: Double quote to prevent globbing and word splitting.
Rework to do a string comparison instead.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Wenwen Wang [Tue, 13 Aug 2019 09:18:52 +0000 (04:18 -0500)]
cxgb4: fix a memory leak bug
In blocked_fl_write(), 't' is not deallocated if bitmap_parse_user() fails,
leading to a memory leak bug. To fix this issue, free t before returning
the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
zhengbin [Tue, 13 Aug 2019 14:05:50 +0000 (22:05 +0800)]
sctp: fix memleak in sctp_send_reset_streams
If the stream outq is not empty, need to kfree nstr_list.
Fixes: d570a59c5b5f ("sctp: only allow the out stream reset when the stream outq is empty") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: zhengbin <zhengbin13@huawei.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The root cause is nlmsg_parse calling __nla_parse which means the
header struct size is not checked.
nlmsg_parse should be a wrapper around __nlmsg_parse with
NL_VALIDATE_STRICT for the validate argument very much like
nlmsg_parse_deprecated is for NL_VALIDATE_LIBERAL.
Fixes: 3de6440354465 ("netlink: re-add parse/validate functions in strict mode") Reported-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Heiner Kallweit [Mon, 12 Aug 2019 19:20:02 +0000 (21:20 +0200)]
net: phy: consider AN_RESTART status when reading link status
After configuring and restarting aneg we immediately try to read the
link status. On some systems the PHY may not yet have cleared the
"aneg complete" and "link up" bits, resulting in a false link-up
signal. See [0] for a report.
Clause 22 and 45 both require the PHY to keep the AN_RESTART
bit set until the PHY actually starts auto-negotiation.
Let's consider this in the generic functions for reading link status.
The commit marked as fixed is the first one where the patch applies
cleanly.
Fixes: c1164bb1a631 ("net: phy: check PMAPMD link status only in genphy_c45_read_link") Tested-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Wenwen Wang [Mon, 12 Aug 2019 19:11:35 +0000 (14:11 -0500)]
net/mlx4_en: fix a memory leak bug
In mlx4_en_config_rss_steer(), 'rss_map->indir_qp' is allocated through
kzalloc(). After that, mlx4_qp_alloc() is invoked to configure RSS
indirection. However, if mlx4_qp_alloc() fails, the allocated
'rss_map->indir_qp' is not deallocated, leading to a memory leak bug.
To fix the above issue, add the 'qp_alloc_err' label to free
'rss_map->indir_qp'.
Fixes: 4931c6ef04b4 ("net/mlx4_en: Optimized single ring steering") Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Thomas Falcon [Mon, 12 Aug 2019 21:13:06 +0000 (16:13 -0500)]
ibmveth: Convert multicast list size for little-endian system
The ibm,mac-address-filters property defines the maximum number of
addresses the hypervisor's multicast filter list can support. It is
encoded as a big-endian integer in the OF device tree, but the virtual
ethernet driver does not convert it for use by little-endian systems.
As a result, the driver is not behaving as it should on affected systems
when a large number of multicast addresses are assigned to the device.
Reported-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Julian Wiedmann [Mon, 12 Aug 2019 14:44:35 +0000 (16:44 +0200)]
s390/qeth: serialize cmd reply with concurrent timeout
Callbacks for a cmd reply run outside the protection of card->lock, to
allow for additional cmds to be issued & enqueued in parallel.
When qeth_send_control_data() bails out for a cmd without having
received a reply (eg. due to timeout), its callback may concurrently be
processing a reply that just arrived. In this case, the callback
potentially accesses a stale reply->reply_param area that eg. was
on-stack and has already been released.
To avoid this race, add some locking so that qeth_send_control_data()
can (1) wait for a concurrently running callback, and (2) zap any
pending callback that still wants to run.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This driver does a funny dance disabling and re-enabling
RX and/or TX delays. In any of the RGMII-ID modes, it first
disables the delays, just to re-enable them again right
away. This looks like a needless exercise.
Just enable the respective delays when in any of the
relevant 'id' modes, and disable them otherwise.
Also, remove comments which don't add anything that can't be
seen by looking at the code.
Signed-off-by: André Draszik <git@andred.net> CC: Andrew Lunn <andrew@lunn.ch> CC: Florian Fainelli <f.fainelli@gmail.com> CC: Heiner Kallweit <hkallweit1@gmail.com> CC: "David S. Miller" <davem@davemloft.net> CC: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
net: tc35815: Explicitly check NET_IP_ALIGN is not zero in tc35815_rx
clang warns:
drivers/net/ethernet/toshiba/tc35815.c:1507:30: warning: use of logical
'&&' with constant operand [-Wconstant-logical-operand]
if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN)
^ ~~~~~~~~~~~~
drivers/net/ethernet/toshiba/tc35815.c:1507:30: note: use '&' for a
bitwise operation
if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN)
^~
&
drivers/net/ethernet/toshiba/tc35815.c:1507:30: note: remove constant to
silence this warning
if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN)
~^~~~~~~~~~~~~~~
1 warning generated.
Explicitly check that NET_IP_ALIGN is not zero, which matches how this
is checked in other parts of the tree. Because NET_IP_ALIGN is a build
time constant, this check will be constant folded away during
optimization.
Fixes: 82a9928db560 ("tc35815: Enable StripCRC feature") Link: https://github.com/ClangBuiltLinux/linux/issues/608 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Packham [Sun, 11 Aug 2019 20:18:25 +0000 (08:18 +1200)]
tipc: initialise addr_trail_end when setting node addresses
We set the field 'addr_trial_end' to 'jiffies', instead of the current
value 0, at the moment the node address is initialized. This guarantees
we don't inadvertently enter an address trial period when the node
address is explicitly set by the user.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chen-Yu Tsai [Sun, 11 Aug 2019 14:18:25 +0000 (22:18 +0800)]
net: dsa: Check existence of .port_mdb_add callback before calling it
The dsa framework has optional .port_mdb_{prepare,add,del} callback fields
for drivers to handle multicast database entries. When adding an entry, the
framework goes through a prepare phase, then a commit phase. Drivers not
providing these callbacks should be detected in the prepare phase.
DSA core may still bypass the bridge layer and call the dsa_port_mdb_add
function directly with no prepare phase or no switchdev trans object,
and the framework ends up calling an undefined .port_mdb_add callback.
This results in a NULL pointer dereference, as shown in the log below.
The other functions seem to be properly guarded. Do the same for
.port_mdb_add in dsa_switch_mdb_add_bitmap() as well.
Petr Machata [Sun, 11 Aug 2019 07:48:37 +0000 (10:48 +0300)]
mlxsw: spectrum_ptp: Keep unmatched entries in a linked list
To identify timestamps for matching with their packets, Spectrum-1 uses a
five-tuple of (port, direction, domain number, message type, sequence ID).
If there are several clients from the same domain behind a single port
sending Delay_Req's, the only thing differentiating these packets, as far
as Spectrum-1 is concerned, is the sequence ID. Should sequence IDs between
individual clients be similar, conflicts may arise. That is not a problem
to hardware, which will simply deliver timestamps on a first comes, first
served basis.
However the driver uses a simple hash table to store the unmatched pieces.
When a new conflicting piece arrives, it pushes out the previously stored
one, which if it is a packet, is delivered without timestamp. Later on as
the corresponding timestamps arrive, the first one is mismatched to the
second packet, and the second one is never matched and eventually is GCd.
To correct this issue, instead of using a simple rhashtable, use rhltable
to keep the unmatched entries.
Previously, a found unmatched entry would always be removed from the hash
table. That is not the case anymore--an incompatible entry is left in the
hash table. Therefore removal from the hash table cannot be used to confirm
the validity of the looked-up pointer, instead the lookup would simply need
to be redone. Therefore move it inside the critical section. This
simplifies a lot of the code.
Fixes: 8748642751ed ("mlxsw: spectrum: PTP: Support SIOCGHWTSTAMP, SIOCSHWTSTAMP ioctls") Reported-by: Alex Veber <alexve@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: syzbot+20dee719a2e090427b5f@syzkaller.appspotmail.com Fixes: 730c5fd42c1e ("rxrpc: Fix local endpoint refcounting") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeffrey Altman <jaltman@auristor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 6 Aug 2019 19:15:17 +0000 (12:15 -0700)]
netdevsim: Restore per-network namespace accounting for fib entries
Prior to the commit in the fixes tag, the resource controller in netdevsim
tracked fib entries and rules per network namespace. Restore that behavior.
Fixes: 5fc494225c1e ("netdevsim: create devlink instance per netdevsim instance") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 10 Aug 2019 01:36:23 +0000 (18:36 -0700)]
net/tls: swap sk_write_space on close
Now that we swap the original proto and clear the ULP pointer
on close we have to make sure no callback will try to access
the freed state. sk_write_space is not part of sk_prot, remember
to swap it.
Reported-by: syzbot+dcdc9deefaec44785f32@syzkaller.appspotmail.com Fixes: 95fa145479fb ("bpf: sockmap/tls, close can race with map free") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dexuan Cui [Fri, 9 Aug 2019 01:58:08 +0000 (01:58 +0000)]
hv_netvsc: Fix a warning of suspicious RCU usage
This fixes a warning of "suspicious rcu_dereference_check() usage"
when nload runs.
Fixes: 776e726bfb34 ("netvsc: fix RCU warning in get_stats") Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights:
1) From Tariq, Critical mlx5 kTLS fixes to better align with hw specs.
2) From Aya, Fixes to mlx5 tx devlink health reporter.
3) From Maxim, aRFs parsing to use flow dissector to avoid relying on
invalid skb fields.
Please pull and let me know if there is any problem.
For -stable v4.3
('net/mlx5e: Only support tx/rx pause setting for port owner')
For -stable v4.9
('net/mlx5e: Use flow keys dissector to parse packets for ARFS')
For -stable v5.1
('net/mlx5e: Fix false negative indication on tx reporter CQE recovery')
('net/mlx5e: Remove redundant check in CQE recovery flow of tx reporter')
('net/mlx5e: ethtool, Avoid setting speed to 56GBASE when autoneg off')
Note: when merged with net-next this minor conflict will pop up:
++<<<<<<< (net-next)
+ if (is_eswitch_flow) {
+ flow->esw_attr->match_level = match_level;
+ flow->esw_attr->tunnel_match_level = tunnel_match_level;
++=======
+ if (flow->flags & MLX5E_TC_FLOW_ESWITCH) {
+ flow->esw_attr->inner_match_level = inner_match_level;
+ flow->esw_attr->outer_match_level = outer_match_level;
++>>>>>>> (net)
To resolve, use hunks from net (2nd) and replace:
if (flow->flags & MLX5E_TC_FLOW_ESWITCH)
with
if (is_eswitch_flow)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Thu, 8 Aug 2019 16:37:56 +0000 (09:37 -0700)]
ixgbe: fix possible deadlock in ixgbe_service_task()
ixgbe_service_task() calls unregister_netdev() under rtnl_lock().
But unregister_netdev() internally calls rtnl_lock().
So deadlock would occur.
Fixes: 59dd45d550c5 ("ixgbe: firmware recovery mode") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Fix collisions in socket cookie generation
This change makes the socket cookie generator as a global counter
instead of per netns in order to fix cookie collisions for BPF use
cases we ran into. See main patch #1 for more details.
Given the change is small/trivial and fixes an issue we're seeing
my preference would be net tree (though it cleanly applies to
net-next as well). Went for net tree instead of bpf tree here given
the main change is in net/core/sock_diag.c, but either way would be
fine with me.
v1 -> v2:
- Fix up commit description in patch #1, thanks Eric!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 8 Aug 2019 11:57:25 +0000 (13:57 +0200)]
sock: make cookie generation global instead of per netns
Generating and retrieving socket cookies are a useful feature that is
exposed to BPF for various program types through bpf_get_socket_cookie()
helper.
The fact that the cookie counter is per netns is quite a limitation
for BPF in practice in particular for programs in host namespace that
use socket cookies as part of a map lookup key since they will be
causing socket cookie collisions e.g. when attached to BPF cgroup hooks
or cls_bpf on tc egress in host namespace handling container traffic
from veth or ipvlan devices with peer in different netns. Change the
counter to be global instead.
Socket cookie consumers must assume the value as opqaue in any case.
Not every socket must have a cookie generated and knowledge of the
counter value itself does not provide much value either way hence
conversion to global is fine.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Willem de Bruijn <willemb@google.com> Cc: Martynas Pumputis <m@lambda.lt> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 9 Aug 2019 15:38:53 +0000 (17:38 +0200)]
Merge branch 'bpf-bpftool-pinning-error-msg'
Jakub Kicinski says:
====================
First make sure we don't use "prog" in error messages because
the pinning operation could be performed on a map. Second add
back missing error message if pin syscall failed.
====================
Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
David Howells [Fri, 9 Aug 2019 14:20:41 +0000 (15:20 +0100)]
rxrpc: Fix local endpoint refcounting
The object lifetime management on the rxrpc_local struct is broken in that
the rxrpc_local_processor() function is expected to clean up and remove an
object - but it may get requeued by packets coming in on the backing UDP
socket once it starts running.
This may result in the assertion in rxrpc_local_rcu() firing because the
memory has been scheduled for RCU destruction whilst still queued:
rxrpc: Assertion failed
------------[ cut here ]------------
kernel BUG at net/rxrpc/local_object.c:468!
Note that if the processor comes around before the RCU free function, it
will just do nothing because ->dead is true.
Fix this by adding a separate refcount to count active users of the
endpoint that causes the endpoint to be destroyed when it reaches 0.
The original refcount can then be used to refcount objects through the work
processor and cause the memory to be rcu freed when that reaches 0.
Fixes: 4f95dd78a77e ("rxrpc: Rework local endpoint management") Reported-by: syzbot+1e0edc4b8b7494c28450@syzkaller.appspotmail.com Signed-off-by: David Howells <dhowells@redhat.com>
Fuqian Huang [Fri, 9 Aug 2019 05:35:39 +0000 (13:35 +0800)]
net: tundra: tsi108: use spin_lock_irqsave instead of spin_lock_irq in IRQ context
As spin_unlock_irq will enable interrupts.
Function tsi108_stat_carry is called from interrupt handler tsi108_irq.
Interrupts are enabled in interrupt handler.
Use spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq
in IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Thu, 8 Aug 2019 06:22:47 +0000 (14:22 +0800)]
team: Add vlan tx offload to hw_enc_features
We should also enable team's vlan tx offload in hw_enc_features,
pass the vlan packets to the slave devices with vlan tci, let the
slave handle vlan tunneling offload implementation.
Fixes: 3268e5cb494d ("team: Advertise tunneling offload features") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 8 Aug 2019 00:03:59 +0000 (17:03 -0700)]
net/tls: prevent skb_orphan() from leaking TLS plain text with offload
sk_validate_xmit_skb() and drivers depend on the sk member of
struct sk_buff to identify segments requiring encryption.
Any operation which removes or does not preserve the original TLS
socket such as skb_orphan() or skb_clone() will cause clear text
leaks.
Make the TCP socket underlying an offloaded TLS connection
mark all skbs as decrypted, if TLS TX is in offload mode.
Then in sk_validate_xmit_skb() catch skbs which have no socket
(or a socket with no validation) and decrypted flag set.
Note that CONFIG_SOCK_VALIDATE_XMIT, CONFIG_TLS_DEVICE and
sk->sk_validate_xmit_skb are slightly interchangeable right now,
they all imply TLS offload. The new checks are guarded by
CONFIG_TLS_DEVICE because that's the option guarding the
sk_buff->decrypted member.
Second, smaller issue with orphaning is that it breaks
the guarantee that packets will be delivered to device
queues in-order. All TLS offload drivers depend on that
scheduling property. This means skb_orphan_partial()'s
trick of preserving partial socket references will cause
issues in the drivers. We need a full orphan, and as a
result netem delay/throttling will cause all TLS offload
skbs to be dropped.
Reusing the sk_buff->decrypted flag also protects from
leaking clear text when incoming, decrypted skb is redirected
(e.g. by TC).
See commit 0608c69c9a80 ("bpf: sk_msg, sock{map|hash} redirect
through ULP") for justification why the internal flag is safe.
The only location which could leak the flag in is tcp_bpf_sendmsg(),
which is taken care of by clearing the previously unused bit.
v2:
- remove superfluous decrypted mark copy (Willem);
- remove the stale doc entry (Boris);
- rely entirely on EOR marking to prevent coalescing (Boris);
- use an internal sendpages flag instead of marking the socket
(Boris).
v3 (Willem):
- reorganize the can_skb_orphan_partial() condition;
- fix the flag leak-in through tcp_bpf_sendmsg.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Boris Pismenny <borisp@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 9 Aug 2019 05:37:06 +0000 (22:37 -0700)]
Merge branch 'skbedit-batch-fixes'
Roman Mashak says:
====================
Fix batched event generation for skbedit action
When adding or deleting a batch of entries, the kernel sends up to
TCA_ACT_MAX_PRIO (defined to 32 in kernel) entries in an event to user
space. However it does not consider that the action sizes may vary and
require different skb sizes.
For example, consider the following script adding 32 entries with all
supported skbedit parameters and cookie (in order to maximize netlink
messages size):
$TC actions flush action skbedit
for i in `seq 1 $1`;
do
cmd="action skbedit queue_mapping 2 priority 10 mark 7/0xaabbccdd \
ptype host inheritdsfield \
index $i cookie aabbccddeeff112233445566778800a1 "
args=$args$cmd
done
$TC actions add $args
%
% ./tc-batch.sh 32
Error: Failed to fill netlink attributes while adding TC action.
We have an error talking to the kernel
%
patch 1 adds callback in tc_action_ops of skbedit action, which calculates
the action size, and passes size to tcf_add_notify()/tcf_del_notify().
patch 2 updates the TDC test suite with relevant skbedit test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Mashak [Wed, 7 Aug 2019 19:57:28 +0000 (15:57 -0400)]
net sched: update skbedit action for batched events operations
Add get_fill_size() routine used to calculate the action size
when building a batch of events.
Fixes: ca9b0e27e ("pkt_action: add new action skbedit") Signed-off-by: Roman Mashak <mrv@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 7 Aug 2019 13:08:56 +0000 (21:08 +0800)]
net: dsa: sja1105: remove set but not used variables 'tx_vid' and 'rx_vid'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/dsa/sja1105/sja1105_main.c: In function sja1105_fdb_dump:
drivers/net/dsa/sja1105/sja1105_main.c:1226:14: warning:
variable tx_vid set but not used [-Wunused-but-set-variable]
drivers/net/dsa/sja1105/sja1105_main.c:1226:6: warning:
variable rx_vid set but not used [-Wunused-but-set-variable]
They are not used since commit 6d7c7d948a2e ("net: dsa:
sja1105: Fix broken learning with vlan_filtering disabled")
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 7 Aug 2019 02:19:59 +0000 (10:19 +0800)]
bonding: Add vlan tx offload to hw_enc_features
As commit 30d8177e8ac7 ("bonding: Always enable vlan tx offload")
said, we should always enable bonding's vlan tx offload, pass the
vlan packets to the slave devices with vlan tci, let them to handle
vlan implementation.
Now if encapsulation protocols like VXLAN is used, skb->encapsulation
may be set, then the packet is passed to vlan device which based on
bonding device. However in netif_skb_features(), the check of
hw_enc_features:
if (skb->encapsulation)
features &= dev->hw_enc_features;
clears NETIF_F_HW_VLAN_CTAG_TX/NETIF_F_HW_VLAN_STAG_TX. This results
in same issue in commit 30d8177e8ac7 like this:
vlan_dev_hard_start_xmit
-->dev_queue_xmit
-->validate_xmit_skb
-->netif_skb_features //NETIF_F_HW_VLAN_CTAG_TX is cleared
-->validate_xmit_vlan
-->__vlan_hwaccel_push_inside //skb->tci is cleared
...
--> bond_start_xmit
--> bond_xmit_hash //BOND_XMIT_POLICY_ENCAP34
--> __skb_flow_dissect // nhoff point to IP header
--> case htons(ETH_P_8021Q)
// skb_vlan_tag_present is false, so
vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
//vlan point to ip header wrongly
Fixes: b2a103e6d0af ("bonding: convert to ndo_fix_features") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Tue, 6 Aug 2019 22:45:40 +0000 (01:45 +0300)]
net: sched: sch_taprio: fix memleak in error path for sched list parse
In error case, all entries should be freed from the sched list
before deleting it. For simplicity use rcu way.
Fixes: 5a781ccbd19e46 ("tc: Add support for configuring the taprio scheduler") Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ross Lagerwall [Mon, 5 Aug 2019 15:34:34 +0000 (16:34 +0100)]
xen/netback: Reset nr_frags before freeing skb
At this point nr_frags has been incremented but the frag does not yet
have a page assigned so freeing the skb results in a crash. Reset
nr_frags before freeing the skb to prevent this.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 2 Aug 2019 15:15:03 +0000 (17:15 +0200)]
inet: frags: re-introduce skb coalescing for local delivery
Before commit d4289fcc9b16 ("net: IP6 defrag: use rbtrees for IPv6
defrag"), a netperf UDP_STREAM test[0] using big IPv6 datagrams (thus
generating many fragments) and running over an IPsec tunnel, reported
more than 6Gbps throughput. After that patch, the same test gets only
9Mbps when receiving on a be2net nic (driver can make a big difference
here, for example, ixgbe doesn't seem to be affected).
By reusing the IPv4 defragmentation code, IPv6 lost fragment coalescing
(IPv4 fragment coalescing was dropped by commit 14fe22e33462 ("Revert
"ipv4: use skb coalescing in defragmentation"")).
Without fragment coalescing, be2net runs out of Rx ring entries and
starts to drop frames (ethtool reports rx_drops_no_frags errors). Since
the netperf traffic is only composed of UDP fragments, any lost packet
prevents reassembly of the full datagram. Therefore, fragments which
have no possibility to ever get reassembled pile up in the reassembly
queue, until the memory accounting exeeds the threshold. At that point
no fragment is accepted anymore, which effectively discards all
netperf traffic.
When reassembly timeout expires, some stale fragments are removed from
the reassembly queue, so a few packets can be received, reassembled
and delivered to the netperf receiver. But the nic still drops frames
and soon the reassembly queue gets filled again with stale fragments.
These long time frames where no datagram can be received explain why
the performance drop is so significant.
Re-introducing fragment coalescing is enough to get the initial
performances again (6.6Gbps with be2net): driver doesn't drop frames
anymore (no more rx_drops_no_frags errors) and the reassembly engine
works at full speed.
This patch is quite conservative and only coalesces skbs for local
IPv4 and IPv6 delivery (in order to avoid changing skb geometry when
forwarding). Coalescing could be extended in the future if need be, as
more scenarios would probably benefit from it.
[0]: Test configuration
Sender:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir in tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir out tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
netserver -D -L fc00:2::1
Receiver:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir in tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir out tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
netperf -H fc00:2::1 -f k -P 0 -L fc00:1::1 -l 60 -t UDP_STREAM -I 99,5 -i 5,5 -T5,5 -6
Signed-off-by: Guillaume Nault <gnault@redhat.com> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Levin [Thu, 8 Aug 2019 12:55:48 +0000 (15:55 +0300)]
net/mlx5e: Remove redundant check in CQE recovery flow of tx reporter
Remove check of recovery bit, in the beginning of the CQE recovery
function. This test is already performed right before the reporter
is invoked, when CQE error is detected.
Aya Levin [Tue, 6 Aug 2019 12:19:19 +0000 (15:19 +0300)]
net/mlx5e: Fix error flow of CQE recovery on tx reporter
CQE recovery function begins with test and set of recovery bit. Add an
error flow which ensures clearing of this bit when leaving the recovery
function, to allow further recoveries to take place. This allows removal
of clearing recovery bit on sq activate.
Aya Levin [Wed, 7 Aug 2019 12:59:06 +0000 (15:59 +0300)]
net/mlx5e: Fix false negative indication on tx reporter CQE recovery
Remove wrong error return value when SQ is not in error state.
CQE recovery on TX reporter queries the sq state. If the sq is not in
error state, the sq is either in ready or reset state. Ready state is
good state which doesn't require recovery and reset state is a temporal
state which ends in ready state. With this patch, CQE recovery in this
scenario is successful.
The TLS progress params context WQE should not include an
Eth segment, drop it.
In addition, align the tls_progress_params layout with the
HW specification document:
- fix the tisn field name.
- remove the valid bit.
net/mlx5: Support inner header match criteria for non decap flow action
We have an issue that OVS application creates an offloaded drop rule
that drops VXLAN traffic with both inner and outer header match
criteria. mlx5_core driver detects correctly the inner and outer
header match criteria but does not enable the inner header match criteria
due to an incorrect assumption in mlx5_eswitch_add_offloaded_rule that
only decap rule needs inner header criteria.
Solution:
Remove mlx5_esw_flow_attr's match_level and tunnel_match_level and add
two new members: inner_match_level and outer_match_level.
inner/outer_match_level is set to NONE if the inner/outer match criteria
is not specified in the tc rule creation request. The decap assumption is
removed and the code just needs to check for inner/outer_match_level to
enable the corresponding bit in firmware's match_criteria_enable value.
Fixes: 6363651d6dd7 ("net/mlx5e: Properly set steering match levels for offloaded TC decap rules") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
net/mlx5e: Use flow keys dissector to parse packets for ARFS
The current ARFS code relies on certain fields to be set in the SKB
(e.g. transport_header) and extracts IP addresses and ports by custom
code that parses the packet. The necessary SKB fields, however, are not
always set at that point, which leads to an out-of-bounds access. Use
skb_flow_dissect_flow_keys() to get the necessary information reliably,
fix the out-of-bounds access and reuse the code.
Pull networking fixes from David Miller:
"Yeah I should have sent a pull request last week, so there is a lot
more here than usual:
1) Fix memory leak in ebtables compat code, from Wenwen Wang.
2) Several kTLS bug fixes from Jakub Kicinski (circular close on
disconnect etc.)
3) Force slave speed check on link state recovery in bonding 802.3ad
mode, from Thomas Falcon.
4) Clear RX descriptor bits before assigning buffers to them in
stmmac, from Jose Abreu.
5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
loops, from Nishka Dasgupta.
6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.
7) Need to hold sock across skb->destructor invocation, from Cong
Wang.
8) IP header length needs to be validated in ipip tunnel xmit, from
Haishuang Yan.
9) Use after free in ip6 tunnel driver, also from Haishuang Yan.
10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
Heiner Kallweit.
11) Upon bridge device init failure, we need to delete the local fdb.
From Nikolay Aleksandrov.
12) Handle erros from of_get_mac_address() properly in stmmac, from
Martin Blumenstingl.
13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
Kadlecsik.
14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
some devices, so revert. From Johannes Berg.
15) Fix deadlock in rxrpc, from David Howells.
16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
Haibing.
17) Fix mvpp2 crash on module removal, from Matteo Croce.
18) Fix race in genphy_update_link, from Heiner Kallweit.
19) bpf_xdp_adjust_head() stopped working with generic XDP when we
fixes generic XDP to support stacked devices properly, fix from
Jesper Dangaard Brouer.
20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
David Ahern.
21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
net: dsa: sja1105: Fix memory leak on meta state machine error path
net: dsa: sja1105: Fix memory leak on meta state machine normal path
net: dsa: sja1105: Really fix panic on unregistering PTP clock
net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
net: sched: sample: allow accessing psample_group with rtnl
net: sched: police: allow accessing police->params with rtnl
net: hisilicon: Fix dma_map_single failed on arm64
net: hisilicon: fix hip04-xmit never return TX_BUSY
net: hisilicon: make hip04_tx_reclaim non-reentrant
tc-testing: updated vlan action tests with batch create/delete
net sched: update vlan action for batched events operations
net: stmmac: tc: Do not return a fragment entry
net: stmmac: Fix issues when number of Queues >= 4
net: stmmac: xgmac: Fix XGMAC selftests
be2net: disable bh with spin_lock in be_process_mcc
net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
...
David S. Miller [Tue, 6 Aug 2019 21:37:02 +0000 (14:37 -0700)]
Merge branch 'sja1105-fixes'
Vladimir Oltean says:
====================
Fixes for SJA1105 DSA: FDBs, Learning and PTP
This is an assortment of functional fixes for the sja1105 switch driver
targeted for the "net" tree (although they apply on net-next just as
well).
Patch 1/5 ("net: dsa: sja1105: Fix broken learning with vlan_filtering
disabled") repairs a breakage introduced in the early development stages
of the driver: support for traffic from the CPU has broken "normal"
frame forwarding (based on DMAC) - there is connectivity through the
switch only because all frames are flooded.
I debated whether this patch qualifies as a fix, since it puts the
switch into a mode it has never operated in before (aka SVL). But
"normal" forwarding did use to work before the "Traffic support for
SJA1105 DSA driver" patchset, and arguably this patch should have been
part of that.
Also, it would be strange for this feature to be broken in the 5.2 LTS.
Patch 2/5 ("net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as
well") is a simplification of a previous FDB-related patch that is
currently in the 5.3 rc's.
Patches 3/5 - 5/5 fix various crashes found while running linuxptp over the
switch ports for extended periods of time, or in conjunction with other
error conditions. The fixed-up commits were all introduced in 5.2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 4 Aug 2019 22:38:48 +0000 (01:38 +0300)]
net: dsa: sja1105: Fix memory leak on meta state machine error path
When RX timestamping is enabled and two link-local (non-meta) frames are
received in a row, this constitutes an error.
The tagger is always caching the last link-local frame, in an attempt to
merge it with the meta follow-up frame when that arrives. To recover
from the above error condition, the initial cached link-local frame is
dropped and the second frame in a row is cached (in expectance of the
second meta frame).
However, when dropping the initial link-local frame, its backing memory
was being leaked.
Fixes: f3097be21bf1 ("net: dsa: sja1105: Add a state machine for RX timestamping") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 4 Aug 2019 22:38:47 +0000 (01:38 +0300)]
net: dsa: sja1105: Fix memory leak on meta state machine normal path
After a meta frame is received, it is associated with the cached
sp->data->stampable_skb from the DSA tagger private structure.
Cached means its refcount is incremented with skb_get() in order for
dsa_switch_rcv() to not free it when the tagger .rcv returns NULL.
The mistake is that skb_unref() is not the correct function to use. It
will correctly decrement the refcount (which will go back to zero) but
the skb memory will not be freed. That is the job of kfree_skb(), which
also calls skb_unref().
But it turns out that freeing the cached stampable_skb is in fact not
necessary. It is still a perfectly valid skb, and now it is even
annotated with the partial RX timestamp. So remove the skb_copy()
altogether and simply pass the stampable_skb with a refcount of 1
(incremented by us, decremented by dsa_switch_rcv) up the stack.
Fixes: f3097be21bf1 ("net: dsa: sja1105: Add a state machine for RX timestamping") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 4 Aug 2019 22:38:46 +0000 (01:38 +0300)]
net: dsa: sja1105: Really fix panic on unregistering PTP clock
The IS_ERR_OR_NULL(priv->clock) check inside
sja1105_ptp_clock_unregister() is preventing cancel_delayed_work_sync
from actually being run.
Additionally, sja1105_ptp_clock_unregister() does not actually get run,
when placed in sja1105_remove(). The DSA switch gets torn down, but the
sja1105 module does not get unregistered. So sja1105_ptp_clock_unregister
needs to be moved to sja1105_teardown, to be symmetrical with
sja1105_ptp_clock_register which is called from the DSA sja1105_setup.
It is strange to fix a "fixes" patch, but the probe failure can only be
seen when the attached PHY does not respond to MDIO (issue which I can't
pinpoint the reason to) and it goes away after I power-cycle the board.
This time the patch was validated on a failing board, and the kernel
panic from the fixed commit's message can no longer be seen.
Fixes: 29dd908d355f ("net: dsa: sja1105: Cancel PTP delayed work on unregister") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 4 Aug 2019 22:38:45 +0000 (01:38 +0300)]
net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
It looks like the FDB dump taken from first-generation switches also
contains information on whether entries are static or not. So use that
instead of searching through the driver's tables.
Fixes: d763778224ea ("net: dsa: sja1105: Implement is_static for FDB entries on E/T") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 4 Aug 2019 22:38:44 +0000 (01:38 +0300)]
net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
When put under a bridge with vlan_filtering 0, the SJA1105 ports will
flood all traffic as if learning was broken. This is because learning
interferes with the rx_vid's configured by dsa_8021q as unique pvid's.
So learning technically still *does* work, it's just that the learnt
entries never get matched due to their unique VLAN ID.
The setting that saves the day is Shared VLAN Learning, which on this
switch family works exactly as desired: VLAN tagging still works
(untagged traffic gets the correct pvid) and FDB entries are still
populated with the correct contents including VID. Also, a frame cannot
violate the forwarding domain restrictions enforced by its classified
VLAN. It is just that the VID is ignored when looking up the FDB for
taking a forwarding decision (selecting the egress port).
This patch activates SVL, and the result is that frames with a learnt
DMAC are no longer flooded in the scenario described above.
Now exactly *because* SVL works as desired, we have to revisit some
earlier patches:
- It is no longer necessary to manipulate the VID of the 'bridge fdb
{add,del}' command when vlan_filtering is off. This is because now,
SVL is enabled for that case, so the actual VID does not matter*.
- It is still desirable to hide dsa_8021q VID's in the FDB dump
callback. But right now the dump callback should no longer hide
duplicates (one per each front panel port's pvid, plus one for the
VLAN that the CPU port is going to tag a TX frame with), because there
shouldn't be any (the switch will match a single FDB entry no matter
its VID anyway).
* Not really... It's no longer necessary to transform a 'bridge fdb add'
into 5 fdb add operations, but the user might still add a fdb entry with
any vid, and all of them would appear as duplicates in 'bridge fdb
show'. So force a 'bridge fdb add' to insert the VID of 0**, so that we
can prune the duplicates at insertion time.
** The VID of 0 is better than 1 because it is always guaranteed to be
in the ports' hardware filter. DSA also avoids putting the VID inside
the netlink response message towards the bridge driver when we return
this particular VID, which makes it suitable for FDB entries learnt
with vlan_filtering off.
Fixes: 227d07a07ef1 ("net: dsa: sja1105: Add support for traffic through standalone ports") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Nishka Dasgupta [Sun, 4 Aug 2019 15:30:18 +0000 (21:00 +0530)]
net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put() before
the return.
Additionally, the local variable ports in the function
qca8k_setup_mdio_bus() takes the return value of of_get_child_by_name(),
which gets a node but does not put it. If the function returns without
putting ports, it may cause a memory leak. Hence put ports before the
mid-loop return statement, and also outside the loop after its last usage
in this function.
Issues found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Aug 2019 21:15:39 +0000 (14:15 -0700)]
Merge branch 'flow_offload-action-fixes'
Vlad Buslov says:
====================
action fixes for flow_offload infra compatibility
Fix rcu warnings due to usage of action helpers that expect rcu read lock
protection from rtnl-protected context of flow_offload infra.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Change tcf_sample_psample_group() helper to allow using it from both rtnl
and rcu protected contexts.
Fixes: a7a7be6087b0 ("net/sched: add sample action to the hardware intermediate representation") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Change tcf_police_rate_bytes_ps() and tcf_police_tcfp_burst() helpers to
allow using them from both rtnl and rcu protected contexts.
Fixes: 8c8cfc6ed274 ("net/sched: add police action to the hardware intermediate representation") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Aug 2019 21:14:01 +0000 (14:14 -0700)]
Merge branch 'hisilicon-fixes'
Jiangfeng Xiao says:
====================
net: hisilicon: Fix a few problems with hip04_eth
During the use of the hip04_eth driver,
several problems were found,
which solved the hip04_tx_reclaim reentry problem,
fixed the problem that hip04_mac_start_xmit never
returns NETDEV_TX_BUSY
and the dma_map_single failed on the arm64 platform.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao [Sat, 3 Aug 2019 12:31:41 +0000 (20:31 +0800)]
net: hisilicon: Fix dma_map_single failed on arm64
On the arm64 platform, executing "ifconfig eth0 up" will fail,
returning "ifconfig: SIOCSIFFLAGS: Input/output error."
ndev->dev is not initialized, dma_map_single->get_dma_ops->
dummy_dma_ops->__dummy_map_page will return DMA_ERROR_CODE
directly, so when we use dma_map_single, the first parameter
is to use the device of platform_device.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao [Sat, 3 Aug 2019 12:31:40 +0000 (20:31 +0800)]
net: hisilicon: fix hip04-xmit never return TX_BUSY
TX_DESC_NUM is 256, in tx_count, the maximum value of
mod(TX_DESC_NUM - 1) is 254, the variable "count" in
the hip04_mac_start_xmit function is never equal to
(TX_DESC_NUM - 1), so hip04_mac_start_xmit never
return NETDEV_TX_BUSY.
tx_count is modified to mod(TX_DESC_NUM) so that
the maximum value of tx_count can reach
(TX_DESC_NUM - 1), then hip04_mac_start_xmit can reurn
NETDEV_TX_BUSY.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao [Sat, 3 Aug 2019 12:31:39 +0000 (20:31 +0800)]
net: hisilicon: make hip04_tx_reclaim non-reentrant
If hip04_tx_reclaim is interrupted while it is running
and then __napi_schedule continues to execute
hip04_rx_poll->hip04_tx_reclaim, reentrancy occurs
and oops is generated. So you need to mask the interrupt
during the hip04_tx_reclaim run.
====================
Fix batched event generation for vlan action
When adding or deleting a batch of entries, the kernel sends up to
TCA_ACT_MAX_PRIO (defined to 32 in kernel) entries in an event to user
space. However it does not consider that the action sizes may vary and
require different skb sizes.
For example, consider the following script adding 32 entries with all
supported vlan parameters (in order to maximize netlink messages size):
$TC actions flush action vlan
for i in `seq 1 $1`;
do
cmd="action vlan push protocol 802.1q id 4094 priority 7 pipe \
index $i cookie aabbccddeeff112233445566778800a1 "
args=$args$cmd
done
$TC actions add $args
%
% ./tc-batch.sh 32
Error: Failed to fill netlink attributes while adding TC action.
We have an error talking to the kernel
%
patch 1 adds callback in tc_action_ops of vlan action, which calculates
the action size, and passes size to tcf_add_notify()/tcf_del_notify().
patch 2 updates the TDC test suite with relevant vlan test cases.
====================
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 6 Aug 2019 21:01:08 +0000 (14:01 -0700)]
Merge tag 'mips_fixes_5.3_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few MIPS fixes for 5.3:
- Various switch fall through annotations to fixup warnings & errors
resulting from -Wimplicit-fallthrough.
- A fix for systems (at least jazz) using an i8253 PIT as clocksource
when it's not suitably configured.
- Set struct cacheinfo's cpu_map_populated field to true, indicating
that we filled in cache info detected from cop0 registers &
avoiding complaints about that info being (intentionally) missing
in devicetree"
* tag 'mips_fixes_5.3_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: BCM63XX: Mark expected switch fall-through
MIPS: OProfile: Mark expected switch fall-throughs
MIPS: Annotate fall-through in Cavium Octeon code
MIPS: Annotate fall-through in kvm/emulate.c
mips: fix cacheinfo
MIPS: kernel: only use i8253 clocksource with periodic clockevent
Jose Abreu [Tue, 6 Aug 2019 13:16:16 +0000 (15:16 +0200)]
net: stmmac: xgmac: Fix XGMAC selftests
Fixup the XGMAC selftests by correctly finishing the implementation of
set_filter callback.
Result:
$ ethtool -t enp4s0
The test result is PASS
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -95
3. MMC Counters -95
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC 0
7. MC Filter 0
8. UC Filter 0
9. Flow Control 0
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Aug 2019 18:48:48 +0000 (11:48 -0700)]
Merge tag 'wireless-drivers-for-davem-2019-08-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.3
Second set of fixes for 5.3. Lots of iwlwifi fixes have accumulated
which consists most of patches in this pull request. Only most notable
iwlwifi fixes are listed below.
mwifiex
* fix a regression related to WPA1 networks since v5.3-rc1
iwlwifi
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 6 Aug 2019 18:47:23 +0000 (11:47 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- functional regression fix for some of the Logitech unifying devices,
from Hans de Goede
- race condition fix in hid-sony for bug severely affecting
Valve/Android deployments, from Roderick Colenbrander
- several fixes for issues found by syzbot/kasan, from Oliver Neukum
and Hillf Danton
- functional regression fix for Wacom Cintiq device, from Aaron
Armstrong Skomra
- a few other assorted device-specific quirks
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: sony: Fix race condition between rumble and device remove.
HID: hiddev: do cleanup in failure of opening a device
HID: hiddev: avoid opening a disconnected device
HID: input: fix a4tech horizontal wheel custom usage
HID: Add quirk for HP X1200 PIXART OEM mouse
HID: holtek: test for sanity of intfdata
HID: wacom: fix bit shift for Cintiq Companion 2
HID: quirks: Set the INCREMENT_USAGE_ON_DUPLICATE quirk on Saitek X52
HID: logitech-dj: Really fix return value of logi_dj_recv_query_hidpp_devices
HID: Add 044f:b320 ThrustMaster, Inc. 2 in 1 DT
HID: logitech-dj: add the Powerplay receiver
HID: logitech-hidpp: add USB PID for a few more supported mice
HID: logitech-dj: rename "gaming" receiver to "lightspeed"
Denis Kirjanov [Tue, 6 Aug 2019 10:51:11 +0000 (12:51 +0200)]
be2net: disable bh with spin_lock in be_process_mcc
be_process_mcc() is invoked in 3 different places and
always with BHs disabled except the be_poll function
but since it's invoked from softirq with BHs
disabled it won't hurt.
v1->v2: added explanation to the patch
v2->v3: add a missing call from be_cmds.c
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Chen-Yu Tsai [Tue, 6 Aug 2019 07:35:39 +0000 (15:35 +0800)]
net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
The sun4i-emac uses the "phy" property to find the PHY it's supposed to
use. This property was deprecated in favor of "phy-handle" in commit 8c5b09447625 ("dt-bindings: net: sun4i-emac: Convert the binding to a
schemas").
Add support for this new property name, and fall back to the old one in
case the device tree hasn't been updated.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 6 Aug 2019 18:22:22 +0000 (11:22 -0700)]
Merge branch 'x86/grand-schemozzle' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull pti updates from Thomas Gleixner:
"The performance deterioration departement is not proud at all to
present yet another set of speculation fences to mitigate the next
chapter in the 'what could possibly go wrong' story.
The new vulnerability belongs to the Spectre class and affects GS
based data accesses and has therefore been dubbed 'Grand Schemozzle'
for secret communication purposes. It's officially listed as
CVE-2019-1125.
Conditional branches in the entry paths which contain a SWAPGS
instruction (interrupts and exceptions) can be mis-speculated which
results in speculative accesses with a wrong GS base.
This can happen on entry from user mode through a mis-speculated
branch which takes the entry from kernel mode path and therefore does
not execute the SWAPGS instruction. The following speculative accesses
are done with user GS base.
On entry from kernel mode the mis-speculated branch executes the
SWAPGS instruction in the entry from user mode path which has the same
effect that the following GS based accesses are done with user GS
base.
If there is a disclosure gadget available in these code paths the
mis-speculated data access can be leaked through the usual side
channels.
The entry from user mode issue affects all CPUs which have speculative
execution. The entry from kernel mode issue affects only Intel CPUs
which can speculate through SWAPGS. On CPUs from other vendors SWAPGS
has semantics which prevent that.
SMAP migitates both problems but only when the CPU is not affected by
the Meltdown vulnerability.
The mitigation is to issue LFENCE instructions in the entry from
kernel mode path for all affected CPUs and on the affected Intel CPUs
also in the entry from user mode path unless PTI is enabled because
the CR3 write is serializing.
The fences are as usual enabled conditionally and can be completely
disabled on the kernel command line. The Spectre V1 documentation is
updated accordingly.
A big "Thank You!" goes to Josh for doing the heavy lifting for this
round of hardware misfeature 'repair'. Of course also "Thank You!" to
everybody else who contributed in one way or the other"
* 'x86/grand-schemozzle' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation: Add swapgs description to the Spectre v1 documentation
x86/speculation/swapgs: Exclude ATOMs from speculation through SWAPGS
x86/entry/64: Use JMP instead of JMPQ
x86/speculation: Enable Spectre v1 swapgs mitigations
x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations
HID: sony: Fix race condition between rumble and device remove.
Valve reported a kernel crash on Ubuntu 18.04 when disconnecting a DS4
gamepad while rumble is enabled. This issue is reproducible with a
frequency of 1 in 3 times in the game Borderlands 2 when using an
automatic weapon, which triggers many rumble operations.
We found the issue to be a race condition between sony_remove and the
final device destruction by the HID / input system. The problem was
that sony_remove didn't clean some of its work_item state in
"struct sony_sc". After sony_remove work, the corresponding evdev
node was around for sufficient time for applications to still queue
rumble work after "sony_remove".
On pre-4.19 kernels the race condition caused a kernel crash due to a
NULL-pointer dereference as "sc->output_report_dmabuf" got freed during
sony_remove. On newer kernels this crash doesn't happen due the buffer
now being allocated using devm_kzalloc. However we can still queue work,
while the driver is an undefined state.
This patch fixes the described problem, by guarding the work_item
"state_worker" with an initialized variable, which we are setting back
to 0 on cleanup.
==================================================================
BUG: KASAN: use-after-free in __lock_acquire+0x302a/0x3b50
kernel/locking/lockdep.c:3753
Read of size 8 at addr ffff8881cf591a08 by task syz-executor.1/26260
Memory state around the buggy address: ffff8881cf591900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881cf591980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ffff8881cf591a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881cf591a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881cf591b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
In order to avoid opening a disconnected device, we need to check exist
again after acquiring the existance lock, and bail out if necessary.
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: bcm63xx_defconfig mips):
arch/mips/pci/ops-bcm63xx.c: In function ‘bcm63xx_pcie_can_access’:
arch/mips/pci/ops-bcm63xx.c:474:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (PCI_SLOT(devfn) == 0)
^
arch/mips/pci/ops-bcm63xx.c:477:2: note: here
default:
^~~~~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: linux-mips@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
Most of the bridge device's vlan init bugs come from the fact that its
default pvid is created at the wrong time, way too early in ndo_init()
before the device is even assigned an ifindex. It introduces a bug when the
bridge's dev_addr is added as fdb during the initial default pvid creation
the notification has ifindex/NDA_MASTER both equal to 0 (see example below)
which really makes no sense for user-space[0] and is wrong.
Usually user-space software would ignore such entries, but they are
actually valid and will eventually have all necessary attributes.
It makes much more sense to send a notification *after* the device has
registered and has a proper ifindex allocated rather than before when
there's a chance that the registration might still fail or to receive
it with ifindex/NDA_MASTER == 0. Note that we can remove the fdb flush
from br_vlan_flush() since that case can no longer happen. At
NETDEV_REGISTER br->default_pvid is always == 1 as it's initialized by
br_vlan_init() before that and at NETDEV_UNREGISTER it can be anything
depending why it was called (if called due to NETDEV_REGISTER error
it'll still be == 1, otherwise it could be any value changed during the
device life time).
For the demonstration below a small change to iproute2 for printing all fdb
notifications is added, because it contained a workaround not to show
entries with ifindex == 0.
Command executed while monitoring: $ ip l add br0 type bridge
Before (both ifindex and master == 0):
$ bridge monitor fdb
36:7e:8a:b3:56:ba dev * vlan 1 master * permanent
After (proper br0 ifindex):
$ bridge monitor fdb
e6:2a:ae:7a:b7:48 dev br0 vlan 1 master br0 permanent
v4: move only the default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
v3: send the correct v2 patch with all changes (stub should return 0)
v2: on error in br_vlan_init set br->vlgrp to NULL and return 0 in
the br_vlan_bridge_event stub when bridge vlans are disabled
Reported-by: michael-dev <michael-dev@fami-braun.de> Fixes: 5be5a2df40f0 ("bridge: Add filtering support for default_pvid") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/marvell/mvmdio.c: Fix non OF case
Orion5.x systems are still using machine files and not device-tree.
Commit 96cb4342382290c9 ("net: mvmdio: allow up to three clocks to be
specified for orion-mdio") has replaced devm_clk_get() with of_clk_get(),
leading to a oops at boot and not working network, as reported in
https://lists.debian.org/debian-arm/2019/07/msg00088.html and possibly in
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908712.
Link: https://lists.debian.org/debian-arm/2019/07/msg00088.html Fixes: 96cb4342382290c9 ("net: mvmdio: allow up to three clocks to be specified for orion-mdio") Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Fri, 2 Aug 2019 08:47:50 +0000 (10:47 +0200)]
net/smc: avoid fallback in case of non-blocking connect
FASTOPEN is not possible with SMC. sendmsg() with msg_flag MSG_FASTOPEN
triggers a fallback to TCP if the socket is in state SMC_INIT.
But if a nonblocking connect is already started, fallback to TCP
is no longer possible, even though the socket may still be in state
SMC_INIT.
And if a nonblocking connect is already started, a listen() call
does not make sense.
Reported-by: syzbot+bd8cc73d665590a1fcad@syzkaller.appspotmail.com Fixes: 50717a37db032 ("net/smc: nonblocking connect rework") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Fri, 2 Aug 2019 08:16:38 +0000 (10:16 +0200)]
net/smc: do not schedule tx_work in SMC_CLOSED state
The setsockopts options TCP_NODELAY and TCP_CORK may schedule the
tx worker. Make sure the socket is not yet moved into SMC_CLOSED
state (for instance by a shutdown SHUT_RDWR call).
Reported-by: syzbot+92209502e7aab127c75f@syzkaller.appspotmail.com Reported-by: syzbot+b972214bb803a343f4fe@syzkaller.appspotmail.com Fixes: 01d2f7e2cdd31 ("net/smc: sockopts TCP_NODELAY and TCP_CORK") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
gve: Fix case where desc_cnt and data_cnt can get out of sync
desc_cnt and data_cnt should always be equal. In the case of a dropped
packet desc_cnt was still getting updated (correctly), data_cnt
was not. To eliminate this bug and prevent it from recurring this
patch combines them into one ring level cnt.
Signed-off-by: Catherine Sullivan <csully@google.com> Reviewed-by: Sagi Shahar <sagis@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 1 Aug 2019 21:36:35 +0000 (14:36 -0700)]
ipv6: Fix unbalanced rcu locking in rt6_update_exception_stamp_rt
The nexthop path in rt6_update_exception_stamp_rt needs to call
rcu_read_unlock if it fails to find a fib6_nh match rather than
just returning.
Fixes: e659ba31d806 ("ipv6: Handle all fib6_nh in a nexthop in exception handling") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / thirdparty / linux.git / log
