recommend you port GNU `make' instead. *Really.* We recommend
version GNU `make' version 3.75 or later.
- * GCC 2.7.2.1
+ * GCC 2.7.2
On most platforms, the GNU C library can only be compiled with the
GNU C compiler. We recommend GCC version 2.7.2 or later; earlier
versions may have problems.
- * `binutils' 2.7
+ * `binutils' 2.8
Using the GNU `binutils' (assembler, linker, and related tools) is
preferable when possible, and they are required to build an ELF
- shared C library. We recommend `binutils' version 2.7 or later;
+ shared C library. We recommend `binutils' version 2.8 or later;
earlier versions are known to have problems or to not support all
architectures.
iX86-ANYTHING-linux
m68k-ANYTHING-linux
- Former versions of this library used to support the following
-configurations but the current status is unknown:
+ Former releases of this library (version 1.09.1 and perhaps earlier
+versions) used to run on the following configurations:
alpha-dec-osf1
iX86-ANYTHING-bsd4.3
sparc-sun-solaris2.N
sparc-sun-sunos4.N
- Each case of `iX86' can be `i386', `i486', `i586', or `i686'.. All
+ Since no one has volunteered to test and fix the above
+configurations, these are not supported at the moment. It's expected
+that these don't work anymore. Porting the library is not hard. If
+you are interested in doing a port, please contact the glibc
+maintainers by sending electronic mail to <bug-glibc@prep.ai.mit.edu>.
+
+ Each case of `iX86' can be `i386', `i486', `i586', or `i686'. All
of those configurations produce a library that can run on any of these
processors. The library will be optimized for the specified processor,
but will not use instructions not available on all of them.
be in whatever directory was current when you ran `configure'.
If you think you have found some way in which the GNU C library does
-not conform to the ANSI and POSIX standards (*note Standards and
+not conform to the ISO and POSIX standards (*note Standards and
Portability::.), that is definitely a bug. Report it!
- Send bug reports to the Internet address `bug-glibc@prep.ai.mit.edu'
-or the UUCP path `mit-eddie!prep.ai.mit.edu!bug-glibc'. If you have
+ Send bug reports to the Internet address <bug-glibc@prep.ai.mit.edu>
+or the UUCP path <mit-eddie!prep.ai.mit.edu!bug-glibc>. If you have
other problems with installation or use, please report those as well.
If you are not sure how a function should behave, and this manual
function's behavior disagrees with the manual, then either the library
or the manual has a bug, so report the disagreement. If you find any
errors or omissions in this manual, please report them to the Internet
-address `bug-glibc-manual@prep.ai.mit.edu' or the UUCP path
-`mit-eddie!prep.ai.mit.edu!bug-glibc-manual'.
+address <bug-glibc-manual@prep.ai.mit.edu> or the UUCP path
+<mit-eddie!prep.ai.mit.edu!bug-glibc-manual>.
Adding New Functions
====================
platforms was written by Per Bothner and modified by Ulrich
Drepper.
- * Some of the Internet-related code (most of the `inet'
- subdirectory) and several other miscellaneous functions and
- header files have been included from 4.4 BSD with little or no
- modification.
+ * The Internet-related code (most of the `inet' subdirectory) and
+ several other miscellaneous functions and header files have been
+ included from 4.4 BSD with little or no modification.
All code incorporated from 4.4 BSD is under the following
copyright:
`rand' and `srand' functions, were written by Earl T. Cohen for
the University of California at Berkeley and are copyrighted by the
Regents of the University of California. They have undergone minor
- changes to fit into the GNU C library and to fit the ANSI C
+ changes to fit into the GNU C library and to fit the ISO C
standard, but the functional code is Berkeley's.
* The Internet resolver code is taken directly from BIND 4.9.5,
Carnegie Mellon University
Pittsburgh PA 15213-3890
- or `Software.Distribution@CS.CMU.EDU' any improvements or
+ or <Software.Distribution@CS.CMU.EDU> any improvements or
extensions that they make and grant Carnegie Mellon the
rights to redistribute these changes.
- * The `getaddrinfo' function is written by Craig Metz and it has the
- following copyright:
-
- The Inner Net License, Version 2.00
- ===================================
-
- The author(s) grant permission for redistribution and use in source and
- binary forms, with or without modification, of the software
- and documentation provided that the following conditions are met:
-
- 0. If you receive a version of the software that is
- specifically labelled as not being for redistribution
- (check the version message and/or README), you are not
- permitted to redistribute that version of the software in
- any way or form.
- 1. All terms of the all other applicable copyrights and
- licenses must be followed.
- 2. Redistributions of source code must retain the authors'
- copyright notice(s), this list of conditions, and the
- following disclaimer.
- 3. Redistributions in binary form must reproduce the authors'
- copyright notice(s), this list of conditions, and the
- following disclaimer in the documentation and/or other
- materials provided with the distribution.
- 4. All advertising materials mentioning features or use of
- this software must display the following acknowledgement
- with the name(s) of the authors as specified in the
- copyright notice(s) substituted where indicated:
-
- This product includes software developed by <name(s)>, The Inner
- Net, and other contributors.
-
- 5. Neither the name(s) of the author(s) nor the names of its
- contributors may be used to endorse or promote products
- derived from this software without specific prior written
- permission.
-
- THIS SOFTWARE IS PROVIDED BY ITS AUTHORS AND CONTRIBUTORS ``AS
- IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
- FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
- SHALL THE AUTHORS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
- INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
- SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
- OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
- LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF
- THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
- OF SUCH DAMAGE.
-
- If these license terms cause you a real problem, contact the author.
%% TeX macros to handle Texinfo files.
-%% $Id: texinfo.tex,v 2.196 1997/01/04 19:24:13 karl Exp $
+%% $Id: texinfo.tex,v 2.196.2.1 1997/05/26 20:55:31 drepper Exp $
% Copyright (C) 1985, 86, 88, 90, 91, 92, 93,
% 94, 95, 96, 97 Free Software Foundation, Inc.
% This automatically updates the version number based on RCS.
\def\deftexinfoversion$#1: #2 ${\def\texinfoversion{#2}}
-\deftexinfoversion$Revision: 2.196 $
+\deftexinfoversion$Revision: 2.196.2.1 $
\message{Loading texinfo package [Version \texinfoversion]:}
% If in a .fmt file, print the version number
\showboxbreadth\maxdimen\showboxdepth\maxdimen
}%
-%---------------------Begin change-----------------------
+% For @cropmarks command.
+% Do @cropmarks to get crop marks.
+%
+\newif\ifcropmarks
+\let\cropmarks = \cropmarkstrue
%
-%%%% For @cropmarks command.
-% Dimensions to add cropmarks at corners Added by P. A. MacKay, 12 Nov. 1986
+% Dimensions to add cropmarks at corners.
+% Added by P. A. MacKay, 12 Nov. 1986
%
\newdimen\cornerlong \newdimen\cornerthick
-\newdimen \topandbottommargin
-\newdimen \outerhsize \newdimen \outervsize
+\newdimen\topandbottommargin
+\newdimen\outerhsize \newdimen\outervsize
\cornerlong=1pc\cornerthick=.3pt % These set size of cropmarks
\outerhsize=7in
%\outervsize=9.5in
% Alternative @smallbook page size is 9.25in
\outervsize=9.25in
\topandbottommargin=.75in
-%
-%---------------------End change-----------------------
% Main output routine.
\chardef\PAGE = 255
\output = {\onepageout{\pagecontents\PAGE}}
-\newbox\headlinebox \newbox\footlinebox
+\newbox\headlinebox
+\newbox\footlinebox
% \onepageout takes a vbox as an argument. Note that \pagecontents
% does insertions, but you have to call it yourself.
\def\onepageout#1{%
- \hoffset=\normaloffset
+ \ifcropmarks \hoffset=0pt \else \hoffset=\normaloffset \fi
+ %
\ifodd\pageno \advance\hoffset by \bindingoffset
\else \advance\hoffset by -\bindingoffset\fi
%
\normalturnoffactive % \ in index entries must not stay \, e.g., if
% the page break happens to be in the middle of an example.
\shipout\vbox{%
+ \ifcropmarks \vbox to \outervsize\bgroup
+ \hsize = \outerhsize
+ \line{\ewtop\hfil\ewtop}%
+ \nointerlineskip
+ \line{%
+ \vbox{\moveleft\cornerthick\nstop}%
+ \hfill
+ \vbox{\moveright\cornerthick\nstop}%
+ }%
+ \vskip\topandbottommargin
+ \line\bgroup
+ \hfil % center the page within the outer (page) hsize.
+ \ifodd\pageno\hskip\bindingoffset\fi
+ \vbox\bgroup
+ \fi
+ %
\unvbox\headlinebox
\pagebody{#1}%
\unvbox\footlinebox
- }%
- }%
+ %
+ \ifcropmarks
+ \egroup % end of \vbox\bgroup
+ \hfil\egroup % end of (centering) \line\bgroup
+ \vskip\topandbottommargin plus1fill minus1fill
+ \boxmaxdepth = \cornerthick
+ \line{%
+ \vbox{\moveleft\cornerthick\nsbot}%
+ \hfill
+ \vbox{\moveright\cornerthick\nsbot}%
+ }%
+ \nointerlineskip
+ \line{\ewbot\hfil\ewbot}%
+ \egroup % \vbox from first cropmarks clause
+ \fi
+ }% end of \shipout\vbox
+ }% end of group with \turnoffactive
\advancepageno
\ifnum\outputpenalty>-20000 \else\dosupereject\fi
}
-%%%% For @cropmarks command %%%%
-
-% Here is a modification of the main output routine for Near East Publications
-% This provides right-angle cropmarks at all four corners.
-% The contents of the page are centerlined into the cropmarks,
-% and any desired binding offset is added as an \hskip on either
-% site of the centerlined box. (P. A. MacKay, 12 November, 1986)
-%
-\def\croppageout#1{\hoffset=0pt % make sure this doesn't mess things up
-{\escapechar=`\\\relax % makes sure backslash is used in output files.
- \shipout
- \vbox to \outervsize{\hsize=\outerhsize
- \vbox{\line{\ewtop\hfill\ewtop}}
- \nointerlineskip
- \line{\vbox{\moveleft\cornerthick\nstop}
- \hfill
- \vbox{\moveright\cornerthick\nstop}}
- \vskip \topandbottommargin
- \centerline{\ifodd\pageno\hskip\bindingoffset\fi
- \vbox{
- {\let\hsize=\pagewidth \makeheadline}
- \pagebody{#1}
- {\let\hsize=\pagewidth \makefootline}}
- \ifodd\pageno\else\hskip\bindingoffset\fi}
- \vskip \topandbottommargin plus1fill minus1fill
- \boxmaxdepth\cornerthick
- \line{\vbox{\moveleft\cornerthick\nsbot}
- \hfill
- \vbox{\moveright\cornerthick\nsbot}}
- \nointerlineskip
- \vbox{\line{\ewbot\hfill\ewbot}}
- }}
- \advancepageno
- \ifnum\outputpenalty>-20000 \else\dosupereject\fi}
-%
-% Do @cropmarks to get crop marks
-\def\cropmarks{\let\onepageout=\croppageout }
-
\newinsert\margin \dimen\margin=\maxdimen
\def\pagebody#1{\vbox to\pageheight{\boxmaxdepth=\maxdepth #1}}
\ifr@ggedbottom \kern-\dimen@ \vfil \fi}
}
-%
% Here are the rules for the cropmarks. Note that they are
% offset so that the space between them is truly \outerhsize or \outervsize
% (P. A. MacKay, 12 November, 1986)
\def\ctrl #1{{\tt \rawbackslash \hat}#1}
\let\file=\samp
-\let\url=\samp % perhaps include a hypertex \special eventually
-\def\email#1{$\langle${\tt #1}$\rangle$}
% @code is a modification of @t,
% which makes spaces the same size as normal in the surrounding text.
\def\realdash{-}
\def\codedash{-\discretionary{}{}{}}
-\def\codeunder{\normalunderscore\discretionary{}{}{}}
+\def\codeunder{\ifusingtt{\normalunderscore\discretionary{}{}{}}{\_}}
\def\codex #1{\tclose{#1}\endgroup}
%\let\exp=\tclose %Was temporary
\else{\tclose{\ttsl\look}}\fi
\else{\tclose{\ttsl\look}}\fi}
+% @url, @email. Quotes do not seem necessary.
+\let\url=\code % perhaps include a hypertex \special eventually
+% rms does not like the angle brackets --karl, 17may97.
+%\def\email#1{$\langle${\tt #1}$\rangle$}
+\let\email=\code
+
% Check if we are currently using a typewriter font. Since all the
% Computer Modern typewriter fonts have zero interword stretch (and
% shrink), and it is reasonable to expect all typewriter fonts to have
\def\r##1{\realbackslash r {##1}}%
\def\i##1{\realbackslash i {##1}}%
\def\b##1{\realbackslash b {##1}}%
+\def\sc##1{\realbackslash sc {##1}}%
\def\cite##1{\realbackslash cite {##1}}%
\def\key##1{\realbackslash key {##1}}%
\def\file##1{\realbackslash file {##1}}%
% Define the macros used in formatting output of the sorted index material.
-% This is what you call to cause a particular index to get printed.
-% Write
-% @unnumbered Function Index
-% @printindex fn
-
+% @printindex causes a particular index (the ??s file) to get printed.
+% It does not print any chapter heading (usually an @unnumbered).
+%
\def\printindex{\parsearg\doprintindex}
-
\def\doprintindex#1{\begingroup
\dobreak \chapheadingskip{10000}%
%
\indexfonts \rm
\tolerance = 9500
\indexbreaks
- \def\indexbackslash{\rawbackslashxx}%
- % Index files are almost Texinfo source, but we use \ as the escape
- % character. It would be better to use @, but that's too big a change
- % to make right now.
- \catcode`\\ = 0
- \catcode`\@ = 11
- \escapechar = `\\
- \begindoublecolumns
%
% See if the index file exists and is nonempty.
\openin 1 \jobname.#1s
\ifeof 1
(Index is empty)
\else
+ % Index files are almost Texinfo source, but we use \ as the escape
+ % character. It would be better to use @, but that's too big a change
+ % to make right now.
+ \def\indexbackslash{\rawbackslashxx}%
+ \catcode`\\ = 0
+ \catcode`\@ = 11
+ \escapechar = `\\
+ \begindoublecolumns
\input \jobname.#1s
+ \enddoublecolumns
\fi
\fi
\closein 1
- \enddoublecolumns
\endgroup}
% These macros are used by the sorted index file itself.
\def\begindoublecolumns{\begingroup % ended by \enddoublecolumns
% Grab any single-column material above us.
- \output = {\global\setbox\partialpage
- =\vbox{\unvbox255\kern -\topskip \kern \baselineskip}}%
+ \output = {\global\setbox\partialpage = \vbox{%
+ %
+ % Here is a possibility not foreseen in manmac: if we accumulate a
+ % whole lot of material, we might end up calling this \output
+ % routine twice in a row (see the doublecol-lose test, which is
+ % essentially a couple of indexes with @setchapternewpage off). In
+ % that case, we must prevent the second \partialpage from
+ % simply overwriting the first, causing us to lose the page.
+ % This will preserve it until a real output routine can ship it
+ % out. Generally, \partialpage will be empty when this runs and
+ % this will be a no-op.
+ \unvbox\partialpage
+ %
+ % Unvbox the main output page.
+ \unvbox255
+ \kern-\topskip \kern\baselineskip
+ }}%
\eject
%
- % Now switch to the double-column output routine.
- \output={\doublecolumnout}%
+ % Use the double-column output routine for subsequent pages.
+ \output = {\doublecolumnout}%
%
% Change the page size parameters. We could do this once outside this
% routine, in each of @smallbook, @afourpaper, and the default 8.5x11
% format, but then we repeat the same computation. Repeating a couple
% of assignments once per index is clearly meaningless for the
- % execution time, so we may as well do it once.
+ % execution time, so we may as well do it in one place.
%
% First we halve the line length, less a little for the gutter between
% the columns. We compute the gutter based on the line length, so it
% changes automatically with the paper format. The magic constant
- % below is chosen so that the gutter has the same value (well, +- <
- % 1pt) as it did when we hard-coded it.
+ % below is chosen so that the gutter has the same value (well, +-<1pt)
+ % as it did when we hard-coded it.
%
% We put the result in a separate register, \doublecolumhsize, so we
% can restore it in \pagesofar, after \hsize itself has (potentially)
% (undoubled) page height minus any material left over from the
% previous page.
\dimen@=\pageheight \advance\dimen@ by-\ht\partialpage
- % box0 will be the left-hand column, box1 the right.
+ % box0 will be the left-hand column, box2 the right.
\setbox0=\vsplit255 to\dimen@ \setbox2=\vsplit255 to\dimen@
\onepageout\pagesofar
- \unvbox255 \penalty\outputpenalty
+ \unvbox255
+ \penalty\outputpenalty
}
\def\pagesofar{%
- % The contents of the output page -- any previous material,
+ % Re-output the contents of the output page -- any previous material,
% followed by the two boxes we just split.
\unvbox\partialpage
\hsize = \doublecolumnhsize
\wd0=\hsize \wd2=\hsize \hbox to\pagewidth{\box0\hfil\box2}%
}
\def\enddoublecolumns{%
- \output={\balancecolumns}\eject % split what we have
- \endgroup
+ \output = {\balancecolumns}\eject % split what we have
+ \endgroup % started in \begindoublecolumns
+ %
% Back to normal single-column typesetting, but take account of the
% fact that we just accumulated some stuff on the output page.
- \pagegoal=\vsize
+ \pagegoal = \vsize
}
\def\balancecolumns{%
- % Called on the last page of the double column material.
- \setbox0=\vbox{\unvbox255}%
+ % Called at the end of the double column material.
+ \setbox0 = \vbox{\unvbox255}%
\dimen@ = \ht0
\advance\dimen@ by \topskip
\advance\dimen@ by-\baselineskip
\divide\dimen@ by 2
\splittopskip = \topskip
% Loop until we get a decent breakpoint.
- {\vbadness=10000 \loop \global\setbox3=\copy0
+ {\vbadness=10000 \loop
+ \global\setbox3=\copy0
\global\setbox1=\vsplit3 to\dimen@
- \ifdim\ht3>\dimen@ \global\advance\dimen@ by1pt \repeat}%
+ \ifdim\ht3>\dimen@ \global\advance\dimen@ by1pt
+ \repeat}%
\setbox0=\vbox to\dimen@{\unvbox1}%
\setbox2=\vbox to\dimen@{\unvbox3}%
\pagesofar
}
-\catcode `\@=\other
+\catcode`\@ = \other
\message{sectioning,}
% Define chapters, sections, etc.
-\newcount \chapno
-\newcount \secno \secno=0
-\newcount \subsecno \subsecno=0
-\newcount \subsubsecno \subsubsecno=0
+\newcount\chapno
+\newcount\secno \secno=0
+\newcount\subsecno \subsecno=0
+\newcount\subsubsecno \subsubsecno=0
% This counter is funny since it counts through charcodes of letters A, B, ...
-\newcount \appendixno \appendixno = `\@
+\newcount\appendixno \appendixno = `\@
\def\appendixletter{\char\the\appendixno}
-\newwrite \contentsfile
+\newwrite\contentsfile
% This is called from \setfilename.
-\def\opencontents{\openout \contentsfile = \jobname.toc}
+\def\opencontents{\openout\contentsfile = \jobname.toc }
% Each @chapter defines this as the name of the chapter.
% page headings and footings can use it. @section does likewise
\def\thischapter{} \def\thissection{}
-\def\seccheck#1{\if \pageno<0 %
-\errmessage{@#1 not allowed after generating table of contents}\fi
-%
-}
+\def\seccheck#1{\ifnum \pageno<0
+ \errmessage{@#1 not allowed after generating table of contents}%
+\fi}
\def\chapternofonts{%
-\let\rawbackslash=\relax%
-\let\frenchspacing=\relax%
-\def\result{\realbackslash result}
-\def\equiv{\realbackslash equiv}
-\def\expansion{\realbackslash expansion}
-\def\print{\realbackslash print}
-\def\TeX{\realbackslash TeX}
-\def\dots{\realbackslash dots}
-\def\copyright{\realbackslash copyright}
-\def\tt{\realbackslash tt}
-\def\bf{\realbackslash bf }
-\def\w{\realbackslash w}
-\def\less{\realbackslash less}
-\def\gtr{\realbackslash gtr}
-\def\hat{\realbackslash hat}
-\def\char{\realbackslash char}
-\def\tclose##1{\realbackslash tclose {##1}}
-\def\code##1{\realbackslash code {##1}}
-\def\samp##1{\realbackslash samp {##1}}
-\def\r##1{\realbackslash r {##1}}
-\def\b##1{\realbackslash b {##1}}
-\def\key##1{\realbackslash key {##1}}
-\def\file##1{\realbackslash file {##1}}
-\def\kbd##1{\realbackslash kbd {##1}}
-% These are redefined because @smartitalic wouldn't work inside xdef.
-\def\i##1{\realbackslash i {##1}}
-\def\cite##1{\realbackslash cite {##1}}
-\def\var##1{\realbackslash var {##1}}
-\def\emph##1{\realbackslash emph {##1}}
-\def\dfn##1{\realbackslash dfn {##1}}
+ \let\rawbackslash=\relax
+ \let\frenchspacing=\relax
+ \def\result{\realbackslash result}%
+ \def\equiv{\realbackslash equiv}%
+ \def\expansion{\realbackslash expansion}%
+ \def\print{\realbackslash print}%
+ \def\TeX{\realbackslash TeX}%
+ \def\dots{\realbackslash dots}%
+ \def\copyright{\realbackslash copyright}%
+ \def\tt{\realbackslash tt}%
+ \def\bf{\realbackslash bf}%
+ \def\w{\realbackslash w}%
+ \def\less{\realbackslash less}%
+ \def\gtr{\realbackslash gtr}%
+ \def\hat{\realbackslash hat}%
+ \def\char{\realbackslash char}%
+ \def\tclose##1{\realbackslash tclose{##1}}%
+ \def\code##1{\realbackslash code{##1}}%
+ \def\samp##1{\realbackslash samp{##1}}%
+ \def\r##1{\realbackslash r{##1}}%
+ \def\b##1{\realbackslash b{##1}}%
+ \def\key##1{\realbackslash key{##1}}%
+ \def\file##1{\realbackslash file{##1}}%
+ \def\kbd##1{\realbackslash kbd{##1}}%
+ % These are redefined because @smartitalic wouldn't work inside xdef.
+ \def\i##1{\realbackslash i{##1}}%
+ \def\cite##1{\realbackslash cite{##1}}%
+ \def\var##1{\realbackslash var{##1}}%
+ \def\emph##1{\realbackslash emph{##1}}%
+ \def\dfn##1{\realbackslash dfn{##1}}%
}
\newcount\absseclevel % used to calculate proper heading level
% because we don't want its macros evaluated now.
\xdef\thischapter{\putwordChapter{} \the\chapno: \noexpand\thischaptername}%
{\chapternofonts%
-\edef\temp{{\realbackslash chapentry {#1}{\the\chapno}{\noexpand\folio}}}%
+\toks0 = {#1}%
+\edef\temp{{\realbackslash chapentry{\the\toks0}{\the\chapno}{\noexpand\folio}}}%
\escapechar=`\\%
\write \contentsfile \temp %
\donoderef %
\gdef\thischaptername{#1}%
\xdef\thischapter{\putwordAppendix{} \appendixletter: \noexpand\thischaptername}%
{\chapternofonts%
-\edef\temp{{\realbackslash chapentry
- {#1}{\putwordAppendix{} \appendixletter}{\noexpand\folio}}}%
+\toks0 = {#1}%
+\edef\temp{{\realbackslash chapentry{\the\toks0}%
+ {\putwordAppendix{} \appendixletter}{\noexpand\folio}}}%
\escapechar=`\\%
\write \contentsfile \temp %
\appendixnoderef %
\unnumbchapmacro {#1}%
\gdef\thischapter{#1}\gdef\thissection{#1}%
{\chapternofonts%
-\edef\temp{{\realbackslash unnumbchapentry {#1}{\noexpand\folio}}}%
+\toks0 = {#1}%
+\edef\temp{{\realbackslash unnumbchapentry{\the\toks0}{\noexpand\folio}}}%
\escapechar=`\\%
\write \contentsfile \temp %
\unnumbnoderef %
\subsecno=0 \subsubsecno=0 \global\advance \secno by 1 %
\gdef\thissection{#1}\secheading {#1}{\the\chapno}{\the\secno}%
{\chapternofonts%
+\toks0 = {#1}%
\edef\temp{{\realbackslash secentry %
-{#1}{\the\chapno}{\the\secno}{\noexpand\folio}}}%
+{\the\toks0}{\the\chapno}{\the\secno}{\noexpand\folio}}}%
\escapechar=`\\%
\write \contentsfile \temp %
\donoderef %
\subsecno=0 \subsubsecno=0 \global\advance \secno by 1 %
\gdef\thissection{#1}\secheading {#1}{\appendixletter}{\the\secno}%
{\chapternofonts%
+\toks0 = {#1}%
\edef\temp{{\realbackslash secentry %
-{#1}{\appendixletter}{\the\secno}{\noexpand\folio}}}%
+{\the\toks0}{\appendixletter}{\the\secno}{\noexpand\folio}}}%
\escapechar=`\\%
\write \contentsfile \temp %
\appendixnoderef %
\def\unnumberedseczzz #1{\seccheck{unnumberedsec}%
\plainsecheading {#1}\gdef\thissection{#1}%
{\chapternofonts%
-\edef\temp{{\realbackslash unnumbsecentry{#1}{\noexpand\folio}}}%
+\toks0 = {#1}%
+\edef\temp{{\realbackslash unnumbsecentry{\the\toks0}{\noexpand\folio}}}%
\escapechar=`\\%
\write \contentsfile \temp %
\unnumbnoderef %
\gdef\thissection{#1}\subsubsecno=0 \global\advance \subsecno by 1 %
\subsecheading {#1}{\the\chapno}{\the\secno}{\the\subsecno}%
{\chapternofonts%
+\toks0 = {#1}%
\edef\temp{{\realbackslash subsecentry %
-{#1}{\the\chapno}{\the\secno}{\the\subsecno}{\noexpand\folio}}}%
+{\the\toks0}{\the\chapno}{\the\secno}{\the\subsecno}{\noexpand\folio}}}%
\escapechar=`\\%
\write \contentsfile \temp %
\donoderef %
\gdef\thissection{#1}\subsubsecno=0 \global\advance \subsecno by 1 %
\subsecheading {#1}{\appendixletter}{\the\secno}{\the\subsecno}%
{\chapternofonts%
+\toks0 = {#1}%
\edef\temp{{\realbackslash subsecentry %
-{#1}{\appendixletter}{\the\secno}{\the\subsecno}{\noexpand\folio}}}%
+{\the\toks0}{\appendixletter}{\the\secno}{\the\subsecno}{\noexpand\folio}}}%
\escapechar=`\\%
\write \contentsfile \temp %
\appendixnoderef %
\def\unnumberedsubseczzz #1{\seccheck{unnumberedsubsec}%
\plainsubsecheading {#1}\gdef\thissection{#1}%
{\chapternofonts%
-\edef\temp{{\realbackslash unnumbsubsecentry{#1}{\noexpand\folio}}}%
+\toks0 = {#1}%
+\edef\temp{{\realbackslash unnumbsubsecentry{\the\toks0}{\noexpand\folio}}}%
\escapechar=`\\%
\write \contentsfile \temp %
\unnumbnoderef %
\subsubsecheading {#1}
{\the\chapno}{\the\secno}{\the\subsecno}{\the\subsubsecno}%
{\chapternofonts%
-\edef\temp{{\realbackslash subsubsecentry %
- {#1}
+\toks0 = {#1}%
+\edef\temp{{\realbackslash subsubsecentry{\the\toks0}
{\the\chapno}{\the\secno}{\the\subsecno}{\the\subsubsecno}
{\noexpand\folio}}}%
\escapechar=`\\%
\subsubsecheading {#1}
{\appendixletter}{\the\secno}{\the\subsecno}{\the\subsubsecno}%
{\chapternofonts%
-\edef\temp{{\realbackslash subsubsecentry{#1}%
+\toks0 = {#1}%
+\edef\temp{{\realbackslash subsubsecentry{\the\toks0}%
{\appendixletter}
{\the\secno}{\the\subsecno}{\the\subsubsecno}{\noexpand\folio}}}%
\escapechar=`\\%
\def\unnumberedsubsubseczzz #1{\seccheck{unnumberedsubsubsec}%
\plainsubsubsecheading {#1}\gdef\thissection{#1}%
{\chapternofonts%
-\edef\temp{{\realbackslash unnumbsubsubsecentry{#1}{\noexpand\folio}}}%
+\toks0 = {#1}%
+\edef\temp{{\realbackslash unnumbsubsubsecentry{\the\toks0}{\noexpand\folio}}}%
\escapechar=`\\%
\write \contentsfile \temp %
\unnumbnoderef %
\let\.=\ptexdot
\let\*=\ptexstar
\let\dots=\ptexdots
-\def\endldots{\mathinner{\ldots\ldots\ldots\ldots}}
-\def\enddots{\relax\ifmmode\endldots\else$\mathsurround=0pt \endldots\,$\fi}
+\def\endldots{\mathinner{\ldots\ldots\ldots\ldots}}%
+\def\enddots{\relax\ifmmode\endldots\else$\mathsurround=0pt \endldots\,$\fi}%
\def\@{@}%
\let\bullet=\ptexbullet
\let\b=\ptexb \let\c=\ptexc \let\i=\ptexi \let\t=\ptext
projects / thirdparty / glibc.git / commitdiff
