commit
31b8b343e019e0a0c57ca9c13520a87f9cab884b upstream.
If the RFkill interrupt fires while we calibrate, it would
make the firmware fail and the driver wasn't able to recover.
Change the flow so that the driver will kill the firmware
in that case.
Since we have now two flows that are calling
trans_stop_device (the RFkill interrupt and the
op_mode_mvm_start function) - we need to better sync this.
Use the STATUS_DEVICE_ENABLED in the pcie transport in an
atomic way to achieve this.
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lockdep_assert_held(&mvm->mutex);
- if (WARN_ON_ONCE(mvm->init_ucode_complete))
+ if (WARN_ON_ONCE(mvm->init_ucode_complete || mvm->calibrating))
return 0;
iwl_init_notification_wait(&mvm->notif_wait,
goto out;
}
+ mvm->calibrating = true;
+
/* Send TX valid antennas before triggering calibrations */
ret = iwl_send_tx_ant_cfg(mvm, mvm->fw->valid_tx_ant);
if (ret)
MVM_UCODE_CALIB_TIMEOUT);
if (!ret)
mvm->init_ucode_complete = true;
+
+ if (ret && iwl_mvm_is_radio_killed(mvm)) {
+ IWL_DEBUG_RF_KILL(mvm, "RFKILL while calibrating.\n");
+ ret = 1;
+ }
goto out;
error:
iwl_remove_notification(&mvm->notif_wait, &calib_wait);
out:
+ mvm->calibrating = false;
if (iwlmvm_mod_params.init_dbg && !mvm->nvm_data) {
/* we want to debug INIT and we have no NVM - fake */
mvm->nvm_data = kzalloc(sizeof(struct iwl_nvm_data) +
iwl_trans_stop_device(mvm->trans);
mvm->scan_status = IWL_MVM_SCAN_NONE;
+ mvm->calibrating = false;
/* just in case one was running */
ieee80211_remain_on_channel_expired(mvm->hw);
enum iwl_ucode_type cur_ucode;
bool ucode_loaded;
bool init_ucode_complete;
+ bool calibrating;
u32 error_event_table;
u32 log_event_table;
u32 umac_error_event_table;
static bool iwl_mvm_set_hw_rfkill_state(struct iwl_op_mode *op_mode, bool state)
{
struct iwl_mvm *mvm = IWL_OP_MODE_GET_MVM(op_mode);
+ bool calibrating = ACCESS_ONCE(mvm->calibrating);
if (state)
set_bit(IWL_MVM_STATUS_HW_RFKILL, &mvm->status);
wiphy_rfkill_set_hw_state(mvm->hw->wiphy, iwl_mvm_is_radio_killed(mvm));
- return state && mvm->cur_ucode != IWL_UCODE_INIT;
+ /* iwl_run_init_mvm_ucode is waiting for results, abort it */
+ if (calibrating)
+ iwl_abort_notification_waits(&mvm->notif_wait);
+
+ /*
+ * Stop the device if we run OPERATIONAL firmware or if we are in the
+ * middle of the calibrations.
+ */
+ return state && (mvm->cur_ucode != IWL_UCODE_INIT || calibrating);
}
static void iwl_mvm_free_skb(struct iwl_op_mode *op_mode, struct sk_buff *skb)
* restart. So don't process again if the device is
* already dead.
*/
- if (test_bit(STATUS_DEVICE_ENABLED, &trans->status)) {
+ if (test_and_clear_bit(STATUS_DEVICE_ENABLED, &trans->status)) {
+ IWL_DEBUG_INFO(trans, "DEVICE_ENABLED bit was set and is now cleared\n");
iwl_pcie_tx_stop(trans);
iwl_pcie_rx_stop(trans);
/* clear all status bits */
clear_bit(STATUS_SYNC_HCMD_ACTIVE, &trans->status);
clear_bit(STATUS_INT_ENABLED, &trans->status);
- clear_bit(STATUS_DEVICE_ENABLED, &trans->status);
clear_bit(STATUS_TPOWER_PMI, &trans->status);
clear_bit(STATUS_RFKILL, &trans->status);