--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/adi,ad4170-4.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices AD4170-4 and similar Analog to Digital Converters
+
+maintainers:
+ - Marcelo Schmitt <marcelo.schmitt@analog.com>
+
+description: |
+ Analog Devices AD4170-4 series of Sigma-delta Analog to Digital Converters.
+ Specifications can be found at:
+ https://www.analog.com/media/en/technical-documentation/data-sheets/ad4170-4.pdf
+ https://www.analog.com/media/en/technical-documentation/data-sheets/ad4190-4.pdf
+ https://www.analog.com/media/en/technical-documentation/data-sheets/ad4195-4.pdf
+
+$ref: /schemas/spi/spi-peripheral-props.yaml#
+
+$defs:
+ reference-buffer:
+ description: |
+ Enable precharge buffer, full buffer, or skip reference buffering of
+ the positive/negative voltage reference. Because the output impedance
+ of the source driving the voltage reference inputs may be dynamic,
+ resistive/capacitive combinations of those inputs can cause DC gain
+ errors if the reference inputs go unbuffered into the ADC. Enable
+ reference buffering if the provided reference source has dynamic high
+ impedance output. Note the absolute voltage allowed on REFINn+ and REFINn-
+ inputs is from AVSS - 50 mV to AVDD + 50 mV when the reference buffers are
+ disabled but narrows to AVSS to AVDD when reference buffering is enabled
+ or in precharge mode.
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [ precharge, full, disabled ]
+ default: full
+
+properties:
+ compatible:
+ enum:
+ - adi,ad4170-4
+ - adi,ad4190-4
+ - adi,ad4195-4
+
+ avss-supply:
+ description:
+ Reference voltage supply for AVSS. A −2.625V minimum and 0V maximum supply
+ that powers the chip. If not provided, AVSS is assumed to be at system
+ ground (0V).
+
+ avdd-supply:
+ description:
+ A supply of 4.75V to 5.25V relative to AVSS that powers the chip (AVDD).
+
+ iovdd-supply:
+ description: 1.7V to 5.25V reference supply to the serial interface (IOVDD).
+
+ refin1p-supply:
+ description: REFIN+ supply that can be used as reference for conversion.
+
+ refin1n-supply:
+ description: REFIN- supply that can be used as reference for conversion.
+
+ refin2p-supply:
+ description: REFIN2+ supply that can be used as reference for conversion.
+
+ refin2n-supply:
+ description: REFIN2- supply that can be used as reference for conversion.
+
+ spi-cpol: true
+
+ spi-cpha: true
+
+ interrupts:
+ description:
+ Interrupt for signaling the completion of conversion results. The data
+ ready signal (RDY) used as interrupt is by default provided on the SDO
+ pin. Alternatively, it can be provided on the DIG_AUX1 pin in which case
+ the chip disables the RDY function on SDO. Thus, there can be only one
+ data ready interrupt enabled at a time.
+
+ interrupt-names:
+ description:
+ Specify which pin should be configured as Data Ready interrupt.
+ enum:
+ - sdo
+ - dig_aux1
+
+ clocks:
+ maxItems: 1
+ description:
+ Optional external clock source. Can specify either an external clock or
+ external crystal.
+
+ clock-names:
+ enum:
+ - ext-clk
+ - xtal
+ default: ext-clk
+
+ '#clock-cells':
+ const: 0
+
+ clock-output-names:
+ maxItems: 1
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+ description: |
+ The first cell is for the GPIO number: 0 to 3.
+ The second cell takes standard GPIO flags.
+
+ ldac-gpios:
+ description:
+ GPIO connected to DIG_AUX2 pin to be used as LDAC toggle to control the
+ transfer of data from the DAC_INPUT_A register to the DAC.
+ maxItems: 1
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+ adi,vbias-pins:
+ description: Analog inputs to apply a voltage bias of (AVDD − AVSS) / 2 to.
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 9
+ items:
+ minimum: 0
+ maximum: 8
+
+allOf:
+ # Some devices don't have integrated DAC
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - adi,ad4190-4
+ - adi,ad4195-4
+ then:
+ properties:
+ ldac-gpios: false
+
+ # Require to specify the interrupt pin when using interrupts
+ - if:
+ required:
+ - interrupts
+ then:
+ required:
+ - interrupt-names
+
+ # If an external clock is set, the internal clock cannot go out and vice versa
+ - oneOf:
+ - required: [clocks]
+ properties:
+ '#clock-cells': false
+ - required: ['#clock-cells']
+ properties:
+ clocks: false
+
+required:
+ - compatible
+ - reg
+ - avdd-supply
+ - iovdd-supply
+ - spi-cpol
+ - spi-cpha
+
+unevaluatedProperties: false
+
+patternProperties:
+ "^channel@[0-9a-f]$":
+ $ref: /schemas/iio/adc/adc.yaml#
+ unevaluatedProperties: false
+ description:
+ Represents the external channels which are connected to the ADC.
+
+ properties:
+ reg:
+ description:
+ The channel number.
+ minimum: 0
+ maximum: 15
+
+ diff-channels:
+ description: |
+ This property is used for defining the inputs of a differential
+ voltage channel. The first value is the positive input and the second
+ value is the negative input of the channel.
+
+ Besides the analog input pins AIN0 to AIN8, there are special inputs
+ that can be selected with the following values:
+ 17: Internal temperature sensor
+ 18: (AVDD-AVSS)/5
+ 19: (IOVDD-DGND)/5
+ 20: DAC output
+ 21: ALDO
+ 22: DLDO
+ 23: AVSS
+ 24: DGND
+ 25: REFIN+
+ 26: REFIN-
+ 27: REFIN2+
+ 28: REFIN2-
+ 29: REFOUT
+ For the internal temperature sensor, use the input number for both
+ inputs (i.e. diff-channels = <17 17>).
+ items:
+ enum: [0, 1, 2, 3, 4, 5, 6, 7, 8, 17, 18, 19, 20, 21, 22, 23, 24, 25,
+ 26, 27, 28, 29]
+
+ adi,reference-select:
+ description: |
+ Select the reference source to use when converting on the
+ specific channel. Valid values are:
+ 0: REFIN+/REFIN-
+ 1: REFIN2+/REFIN2−
+ 2: REFOUT/AVSS (internal reference)
+ 3: AVDD/AVSS
+ If not specified, REFOUT/AVSS is used.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 1
+
+ adi,positive-reference-buffer:
+ $ref: '#/$defs/reference-buffer'
+
+ adi,negative-reference-buffer:
+ $ref: '#/$defs/reference-buffer'
+
+ adi,sensor-type:
+ description:
+ The AD4170-4 and similar designs have features to aid interfacing with
+ load cell weigh scale, RTD, and thermocouple sensors. Each of those
+ sensor types requires either distinct wiring configuration or
+ external circuitry for proper sensor operation and can use different
+ ADC chip functionality on their setups. A key characteristic of those
+ external sensors is that they must be excited either by voltage supply
+ or by ADC chip excitation signals. The sensor can then be read through
+ a pair of analog inputs. This property specifies which particular
+ sensor type is connected to the ADC so it can be properly setup and
+ handled. Omit this property for conventional (not weigh scale, RTD, or
+ thermocouple) ADC channel setups.
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [ weighscale, rtd, thermocouple ]
+
+ adi,excitation-pin-0:
+ description:
+ Analog input to apply excitation current to while the channel
+ is active.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 20
+ default: 0
+
+ adi,excitation-pin-1:
+ description:
+ Analog input to apply excitation current to while the channel
+ is active.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 20
+ default: 0
+
+ adi,excitation-pin-2:
+ description:
+ Analog input to apply excitation current to while the channel
+ is active.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 20
+ default: 0
+
+ adi,excitation-pin-3:
+ description:
+ Analog input to apply excitation current to while the channel
+ is active.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 20
+ default: 0
+
+ adi,excitation-current-0-microamp:
+ description:
+ Excitation current in microamperes to be applied to pin specified in
+ adi,excitation-pin-0 while this channel is active.
+ enum: [0, 10, 50, 100, 250, 500, 1000, 1500]
+ default: 0
+
+ adi,excitation-current-1-microamp:
+ description:
+ Excitation current in microamperes to be applied to pin specified in
+ adi,excitation-pin-1 while this channel is active.
+ enum: [0, 10, 50, 100, 250, 500, 1000, 1500]
+ default: 0
+
+ adi,excitation-current-2-microamp:
+ description:
+ Excitation current in microamperes to be applied to pin specified in
+ adi,excitation-pin-2 while this channel is active.
+ enum: [0, 10, 50, 100, 250, 500, 1000, 1500]
+ default: 0
+
+ adi,excitation-current-3-microamp:
+ description:
+ Excitation current in microamperes to be applied to pin specified in
+ adi,excitation-pin-3 while this channel is active.
+ enum: [0, 10, 50, 100, 250, 500, 1000, 1500]
+ default: 0
+
+ adi,excitation-ac:
+ type: boolean
+ description:
+ Whether the external sensor has to be AC or DC excited. When omitted,
+ it is DC excited.
+
+ allOf:
+ - oneOf:
+ - required: [single-channel, common-mode-channel]
+ properties:
+ diff-channels: false
+ - required: [diff-channels]
+ properties:
+ single-channel: false
+ common-mode-channel: false
+ # Usual ADC channels don't need external circuitry excitation.
+ - if:
+ not:
+ required:
+ - adi,sensor-type
+ then:
+ properties:
+ adi,excitation-pin-0: false
+ adi,excitation-pin-1: false
+ adi,excitation-pin-2: false
+ adi,excitation-pin-3: false
+ adi,excitation-current-0-microamp: false
+ adi,excitation-current-1-microamp: false
+ adi,excitation-current-2-microamp: false
+ adi,excitation-current-3-microamp: false
+ adi,excitation-ac: false
+ # Weigh scale bridge AC excited with one pair of predefined signals.
+ - if:
+ allOf:
+ - properties:
+ adi,sensor-type:
+ contains:
+ const: weighscale
+ - required:
+ - adi,excitation-ac
+ - adi,excitation-pin-2
+ - adi,excitation-pin-3
+ - not:
+ required:
+ - adi,excitation-current-2-microamp
+ - adi,excitation-current-3-microamp
+ then:
+ properties:
+ adi,excitation-pin-2:
+ const: 19
+ adi,excitation-pin-3:
+ const: 20
+ # Weigh scale bridge AC excited with two pairs of predefined signals.
+ - if:
+ allOf:
+ - properties:
+ adi,sensor-type:
+ contains:
+ const: weighscale
+ - required:
+ - adi,excitation-ac
+ - adi,excitation-pin-0
+ - adi,excitation-pin-1
+ - adi,excitation-pin-2
+ - adi,excitation-pin-3
+ - not:
+ required:
+ - adi,excitation-current-0-microamp
+ - adi,excitation-current-1-microamp
+ - adi,excitation-current-2-microamp
+ - adi,excitation-current-3-microamp
+ then:
+ properties:
+ adi,excitation-pin-0:
+ const: 17
+ adi,excitation-pin-1:
+ const: 18
+ adi,excitation-pin-2:
+ const: 19
+ adi,excitation-pin-3:
+ const: 20
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@0 {
+ compatible = "adi,ad4170-4";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ spi-cpol;
+ spi-cpha;
+ avdd-supply = <&avdd>;
+ iovdd-supply = <&iovdd>;
+ clocks = <&clk>;
+ clock-names = "xtal";
+ interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "dig_aux1";
+ adi,vbias-pins = <8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ // Sample AIN0 with respect to DGND throughout AVDD/DGND input range
+ // Pseudo-differential unipolar
+ channel@0 {
+ reg = <0>;
+ single-channel = <0>;
+ common-mode-channel = <24>;
+ adi,reference-select = <3>;
+ };
+ // Weigh scale sensor
+ channel@1 {
+ reg = <1>;
+ bipolar;
+ diff-channels = <1 2>;
+ adi,reference-select = <0>;
+ adi,positive-reference-buffer = "precharge";
+ adi,negative-reference-buffer = "precharge";
+ adi,sensor-type = "weighscale";
+ adi,excitation-pin-2 = <19>;
+ adi,excitation-pin-3 = <20>;
+ adi,excitation-ac;
+ };
+ // RTD sensor
+ channel@2 {
+ reg = <2>;
+ bipolar;
+ diff-channels = <3 4>;
+ adi,reference-select = <0>;
+ adi,sensor-type = "rtd";
+ adi,excitation-pin-0 = <5>;
+ adi,excitation-pin-1 = <6>;
+ adi,excitation-current-0-microamp = <500>;
+ adi,excitation-current-1-microamp = <500>;
+ adi,excitation-ac;
+ };
+ // Thermocouple sensor
+ channel@3 {
+ reg = <3>;
+ bipolar;
+ diff-channels = <7 8>;
+ adi,reference-select = <0>;
+ adi,sensor-type = "thermocouple";
+ adi,excitation-pin-0 = <18>;
+ adi,excitation-current-0-microamp = <500>;
+ };
+ };
+ };
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@0 {
+ compatible = "adi,ad4170-4";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ spi-cpol;
+ spi-cpha;
+ avdd-supply = <&avdd>;
+ iovdd-supply = <&iovdd>;
+ #clock-cells = <0>;
+ clock-output-names = "ad4170-clk16mhz";
+ interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "dig_aux1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ // Sample AIN0 with respect to AIN1 throughout AVDD/AVSS input range
+ // Differential bipolar. If AVSS < 0V, differential true bipolar
+ channel@0 {
+ reg = <0>;
+ bipolar;
+ diff-channels = <0 1>;
+ adi,reference-select = <3>;
+ };
+ // Sample AIN2 with respect to DGND throughout AVDD/DGND input range
+ // Pseudo-differential unipolar
+ channel@1 {
+ reg = <1>;
+ single-channel = <2>;
+ common-mode-channel = <24>;
+ adi,reference-select = <3>;
+ };
+ // Sample AIN3 with respect to 2.5V throughout AVDD/AVSS input range
+ // Pseudo-differential bipolar
+ channel@2 {
+ reg = <2>;
+ bipolar;
+ single-channel = <3>;
+ common-mode-channel = <29>;
+ adi,reference-select = <3>;
+ };
+ // Sample AIN4 with respect to DGND throughout AVDD/AVSS input range
+ // Pseudo-differential bipolar
+ channel@3 {
+ reg = <3>;
+ bipolar;
+ single-channel = <4>;
+ common-mode-channel = <24>;
+ adi,reference-select = <3>;
+ };
+ // Sample AIN5 with respect to 2.5V throughout AVDD/AVSS input range
+ // Pseudo-differential unipolar (AD4170-4 datasheet page 46 example)
+ channel@4 {
+ reg = <4>;
+ single-channel = <5>;
+ common-mode-channel = <29>;
+ adi,reference-select = <3>;
+ };
+ // Sample AIN6 with respect to 2.5V throughout REFIN+/REFIN- input range
+ // Pseudo-differential bipolar
+ channel@5 {
+ reg = <5>;
+ bipolar;
+ single-channel = <6>;
+ common-mode-channel = <29>;
+ adi,reference-select = <0>;
+ };
+ // Weigh scale sensor
+ channel@6 {
+ reg = <6>;
+ bipolar;
+ diff-channels = <7 8>;
+ adi,reference-select = <0>;
+ adi,sensor-type = "weighscale";
+ adi,excitation-pin-0 = <17>;
+ adi,excitation-pin-1 = <18>;
+ adi,excitation-pin-2 = <19>;
+ adi,excitation-pin-3 = <20>;
+ adi,excitation-ac;
+ };
+ };
+ };
+...
projects / thirdparty / kernel / stable.git / commitdiff
