The edt,edt-ft5x06 compatible is not referenced in
drivers/input/touchscreen/edt-ft5x06.c and is not documented.
There is no publicly available datasheet or binding information that
distinguishes edt-ft5206/ft5306/ft5406 variants and the driver treats these
FT5x06-family controllers with the same configuration model. So switch to
the lowest common and documented baseline compatible edt,edt-ft5206.
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx53-m53menlo.dtb: /soc/bus@
60000000/i2c@
63fc8000/touchscreen@38: failed to match any schema with compatible: ['edt,edt-ft5x06']
ABI impact consideration:
Not affect Linux kernel. The I2C subsystem uses a legacy fallback mechanism
where it strips the vendor prefix from the compatible string to derive the
client name, resulting in edt-ft5x06
{ .name = "edt-ft5x06", .driver_data = (long)&edt_ft5x06_data },
After this, the driver was actively binding to these devices based on the
compatible string.
Known user (U-Boot) does not parse or use edt,edt-ft* touchscreen
compatibles.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
status = "okay";
touchscreen@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_edt_ft5x06>;
};
polytouch: edt-ft5x06@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_edt_ft5x06_1>;
status = "okay";
touchscreen@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
interrupt-parent = <&gpio1>;
interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
};
touchscreen@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
interrupt-parent = <&gpio1>;
interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
};
touchscreen@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
interrupt-parent = <&gpio1>;
interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
};
touchscreen@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
interrupt-parent = <&gpio1>;
interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
};
touchscreen@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
interrupt-parent = <&gpio1>;
interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
status = "okay";
touchscreen@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
interrupt-parent = <&gpio5>;
interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
};
polytouch: edt-ft5x06@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_edt_ft5x06>;
status = "okay";
polytouch: touchscreen@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
interrupt-parent = <&gpio1>;
interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
status = "okay";
polytouch: touchscreen@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
interrupt-parent = <&gpio1>;
interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
};
polytouch: polytouch@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_edt_ft5x06>;
};
touchscreen@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_touchscreen>;
&i2c4 {
polytouch: touchscreen@38 {
- compatible = "edt,edt-ft5x06";
+ compatible = "edt,edt-ft5206";
reg = <0x38>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_touchscreen>;