#include <linux/dev_printk.h>
#include <linux/device/devres.h>
#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/kstrtox.h>
#include <linux/limits.h>
#include <linux/math.h>
#include <linux/module.h>
#include <linux/mod_devicetable.h>
+#include <linux/property.h>
+#include <linux/pwm.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/reset.h>
+#include <linux/string.h>
#include <linux/spi/spi.h>
#include <linux/types.h>
#include <linux/units.h>
#include <linux/unaligned.h>
+#include <linux/iio/buffer.h>
#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/trigger_consumer.h>
#define AD4691_VREF_uV_MIN 2400000
#define AD4691_VREF_uV_MAX 5250000
#define AD4691_NOOP 0x00
#define AD4691_ADC_CHAN(ch) ((0x10 + (ch)) << 3)
+#define AD4691_EXIT_COMMAND 0x5000
#define AD4691_OSC_EN_REG 0x180
#define AD4691_STATE_RESET_REG 0x181
.info_mask_shared_by_all_available = \
BIT(IIO_CHAN_INFO_SAMP_FREQ), \
.channel = ch, \
+ .scan_index = ch, \
.scan_type = { \
+ .format = 'u', \
.realbits = 16, \
+ .storagebits = 16, \
+ .endianness = IIO_BE, \
}, \
}
AD4691_CHANNEL(13),
AD4691_CHANNEL(14),
AD4691_CHANNEL(15),
+ IIO_CHAN_SOFT_TIMESTAMP(16),
};
static const struct iio_chan_spec ad4693_channels[] = {
AD4691_CHANNEL(5),
AD4691_CHANNEL(6),
AD4691_CHANNEL(7),
+ IIO_CHAN_SOFT_TIMESTAMP(8),
};
static const struct ad4691_channel_info ad4691_sw_info = {
[0xF] = 1250,
};
+static const char * const ad4691_gp_names[] = { "gp0", "gp1", "gp2", "gp3" };
+
static const struct ad4691_chip_info ad4691_chip_info = {
.name = "ad4691",
.max_rate = 500 * HZ_PER_KHZ,
struct regmap *regmap;
struct spi_device *spi;
+ struct pwm_device *conv_trigger;
+ int irq;
int vref_uV;
+ u32 cnv_period_ns;
+ bool manual_mode;
+ bool irq_enabled;
bool refbuf_en;
bool ldo_en;
/*
* atomicity of consecutive SPI operations.
*/
struct mutex lock;
+ /*
+ * Per-buffer-enable lifetime resources:
+ * Manual Mode - a pre-built SPI message that clocks out N+1
+ * transfers in one go.
+ * CNV Burst Mode - a pre-built SPI message that clocks out 2*N
+ * transfers in one go.
+ */
+ struct spi_message scan_msg;
+ /*
+ * max 16 + 1 NOOP (manual) or 2*16 + 1 state-reset (CNV burst).
+ */
+ struct spi_transfer scan_xfers[34];
+ /*
+ * CNV burst: 16 AVG_IN addresses = 16. Manual: 16 channel cmds +
+ * 1 NOOP = 17. Stored as native u16; put_unaligned_be16() fills each
+ * slot so the SPI controller (bits_per_word=8) sends bytes MSB-first.
+ */
+ u16 scan_tx[17] __aligned(IIO_DMA_MINALIGN);
+ /*
+ * CNV burst state-reset: 4-byte write [addr_hi, addr_lo,
+ * STATE_RESET_ALL, OSC_EN=1]. CS is asserted throughout, so
+ * ADDR_DESCENDING writes byte[3]=1 to OSC_EN_REG (0x180) as a
+ * deliberate side-write, keeping the oscillator enabled. Shared
+ * with the offload path (mutually exclusive at probe).
+ */
+ u8 scan_tx_reset[4] __aligned(IIO_DMA_MINALIGN);
+ /*
+ * Scan buffer: one BE16 slot per active channel, plus timestamp.
+ * DMA-aligned because scan_xfers point rx_buf directly into vals[].
+ */
+ IIO_DECLARE_DMA_BUFFER_WITH_TS(__be16, vals, 16);
};
+/*
+ * Configure the given GP pin (0-3) as DATA_READY output.
+ * GP0/GP1 → GPIO_MODE1_REG, GP2/GP3 → GPIO_MODE2_REG.
+ * Even pins occupy bits [3:0], odd pins bits [7:4].
+ */
+static int ad4691_gpio_setup(struct ad4691_state *st, unsigned int gp_num)
+{
+ unsigned int bit_off = gp_num % 2;
+ unsigned int reg_off = gp_num / 2;
+ unsigned int shift = 4 * bit_off;
+
+ return regmap_update_bits(st->regmap,
+ AD4691_GPIO_MODE1_REG + reg_off,
+ AD4691_GP_MODE_MASK << shift,
+ AD4691_GP_MODE_DATA_READY << shift);
+}
+
static int ad4691_reg_read(void *context, unsigned int reg, unsigned int *val)
{
struct spi_device *spi = context;
return regmap_write(st->regmap, reg, writeval);
}
-static const struct iio_info ad4691_info = {
+static int ad4691_set_pwm_freq(struct ad4691_state *st, unsigned int freq)
+{
+ if (!freq)
+ return -EINVAL;
+
+ st->cnv_period_ns = DIV_ROUND_UP(NSEC_PER_SEC, freq);
+ return 0;
+}
+
+static int ad4691_sampling_enable(struct ad4691_state *st, bool enable)
+{
+ struct pwm_state conv_state = {
+ .period = st->cnv_period_ns,
+ .duty_cycle = AD4691_CNV_DUTY_CYCLE_NS,
+ .polarity = PWM_POLARITY_NORMAL,
+ .enabled = enable,
+ };
+
+ return pwm_apply_might_sleep(st->conv_trigger, &conv_state);
+}
+
+/*
+ * ad4691_enter_conversion_mode - Switch the chip to its buffer conversion mode.
+ *
+ * Configures the ADC hardware registers for the mode selected at probe
+ * (CNV_BURST or MANUAL). Called from buffer preenable before starting
+ * sampling. The chip is in AUTONOMOUS mode during idle (for read_raw).
+ */
+static int ad4691_enter_conversion_mode(struct ad4691_state *st)
+{
+ int ret;
+
+ if (st->manual_mode)
+ return regmap_update_bits(st->regmap, AD4691_DEVICE_SETUP,
+ AD4691_MANUAL_MODE, AD4691_MANUAL_MODE);
+
+ ret = regmap_update_bits(st->regmap, AD4691_ADC_SETUP,
+ AD4691_ADC_MODE_MASK, AD4691_CNV_BURST_MODE);
+ if (ret)
+ return ret;
+
+ return regmap_write(st->regmap, AD4691_STATE_RESET_REG,
+ AD4691_STATE_RESET_ALL);
+}
+
+static int ad4691_transfer(struct ad4691_state *st, u16 cmd)
+{
+ u8 buf[2];
+
+ put_unaligned_be16(cmd, buf);
+
+ return spi_write_then_read(st->spi, buf, sizeof(buf), NULL, 0);
+}
+
+/*
+ * ad4691_exit_conversion_mode - Return the chip to AUTONOMOUS mode.
+ *
+ * Called from buffer postdisable to restore the chip to the
+ * idle state used by read_raw. Clears the sequencer and resets state.
+ */
+static int ad4691_exit_conversion_mode(struct ad4691_state *st)
+{
+ if (st->manual_mode)
+ return ad4691_transfer(st, AD4691_EXIT_COMMAND);
+
+ return regmap_update_bits(st->regmap, AD4691_ADC_SETUP,
+ AD4691_ADC_MODE_MASK, AD4691_AUTONOMOUS_MODE);
+}
+
+static int ad4691_manual_buffer_preenable(struct iio_dev *indio_dev)
+{
+ struct ad4691_state *st = iio_priv(indio_dev);
+ unsigned int k, i;
+ int ret;
+
+ memset(st->scan_xfers, 0, sizeof(st->scan_xfers));
+ memset(st->scan_tx, 0, sizeof(st->scan_tx));
+
+ spi_message_init(&st->scan_msg);
+
+ k = 0;
+ iio_for_each_active_channel(indio_dev, i) {
+ /*
+ * Channel-select command occupies the first (high) byte of the
+ * 16-bit DIN frame; the second byte is a don't-care zero pad.
+ * put_unaligned_be16() writes [cmd, 0x00] in memory so the
+ * SPI controller sends the command byte first on the wire.
+ */
+ put_unaligned_be16((u16)(AD4691_ADC_CHAN(i) << 8), &st->scan_tx[k]);
+ st->scan_xfers[k].tx_buf = &st->scan_tx[k];
+ /*
+ * The pipeline means xfer[0] receives the residual from the
+ * previous sequence, not a valid sample. Discard it (rx_buf=NULL)
+ * to avoid aliasing vals[0] across two concurrent DMA mappings.
+ * xfer[1] (or the NOOP when only one channel is active) writes
+ * the real ch[0] result to vals[0]. Subsequent transfers write
+ * into vals[k-1] so each result lands at the next dense slot.
+ */
+ st->scan_xfers[k].rx_buf = (k == 0) ? NULL : &st->vals[k - 1];
+ st->scan_xfers[k].len = sizeof(*st->scan_tx);
+ st->scan_xfers[k].cs_change = 1;
+ st->scan_xfers[k].cs_change_delay.value = AD4691_CNV_HIGH_TIME_NS;
+ st->scan_xfers[k].cs_change_delay.unit = SPI_DELAY_UNIT_NSECS;
+ spi_message_add_tail(&st->scan_xfers[k], &st->scan_msg);
+ k++;
+ }
+
+ /* Final NOOP transfer retrieves the last channel's result. */
+ st->scan_xfers[k].tx_buf = &st->scan_tx[k]; /* scan_tx[k] == 0 == NOOP */
+ st->scan_xfers[k].rx_buf = &st->vals[k - 1];
+ st->scan_xfers[k].len = sizeof(*st->scan_tx);
+ spi_message_add_tail(&st->scan_xfers[k], &st->scan_msg);
+
+ ret = spi_optimize_message(st->spi, &st->scan_msg);
+ if (ret)
+ return ret;
+
+ ret = ad4691_enter_conversion_mode(st);
+ if (ret) {
+ spi_unoptimize_message(&st->scan_msg);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int ad4691_manual_buffer_postdisable(struct iio_dev *indio_dev)
+{
+ struct ad4691_state *st = iio_priv(indio_dev);
+ int ret;
+
+ ret = ad4691_exit_conversion_mode(st);
+ spi_unoptimize_message(&st->scan_msg);
+ return ret;
+}
+
+static const struct iio_buffer_setup_ops ad4691_manual_buffer_setup_ops = {
+ .preenable = ad4691_manual_buffer_preenable,
+ .postdisable = ad4691_manual_buffer_postdisable,
+};
+
+static int ad4691_cnv_burst_buffer_preenable(struct iio_dev *indio_dev)
+{
+ struct ad4691_state *st = iio_priv(indio_dev);
+ unsigned int acc_mask, std_seq_config;
+ unsigned int k, i;
+ int ret;
+
+ memset(st->scan_xfers, 0, sizeof(st->scan_xfers));
+ memset(st->scan_tx, 0, sizeof(st->scan_tx));
+
+ spi_message_init(&st->scan_msg);
+
+ /*
+ * Each AVG_IN read needs two transfers: a 2-byte address write phase
+ * followed by a 2-byte data read phase. CS toggles between channels
+ * (cs_change=1 on the read phase of all but the last channel).
+ */
+ k = 0;
+ iio_for_each_active_channel(indio_dev, i) {
+ put_unaligned_be16(0x8000 | AD4691_AVG_IN(i), &st->scan_tx[k]);
+ st->scan_xfers[2 * k].tx_buf = &st->scan_tx[k];
+ st->scan_xfers[2 * k].len = sizeof(*st->scan_tx);
+ spi_message_add_tail(&st->scan_xfers[2 * k], &st->scan_msg);
+ st->scan_xfers[2 * k + 1].rx_buf = &st->vals[k];
+ st->scan_xfers[2 * k + 1].len = sizeof(*st->scan_tx);
+ st->scan_xfers[2 * k + 1].cs_change = 1;
+ spi_message_add_tail(&st->scan_xfers[2 * k + 1], &st->scan_msg);
+ k++;
+ }
+
+ /*
+ * Append a 4-byte state-reset transfer [addr_hi, addr_lo,
+ * STATE_RESET_ALL, OSC_EN=1]. CS is asserted throughout, so
+ * ADDR_DESCENDING writes byte[3]=1 to OSC_EN_REG (0x180) as a
+ * deliberate side-write, keeping the oscillator enabled.
+ * STATE_RESET_ALL starts the next burst; the hardware does not
+ * accumulate new conversions until after a STATE_RESET pulse, so
+ * no in-progress data is lost. No cs_change here — CS must
+ * deassert normally at end of message to frame the next command.
+ */
+ put_unaligned_be16(AD4691_STATE_RESET_REG, st->scan_tx_reset);
+ st->scan_tx_reset[2] = AD4691_STATE_RESET_ALL;
+ st->scan_tx_reset[3] = 1;
+ st->scan_xfers[2 * k].tx_buf = st->scan_tx_reset;
+ st->scan_xfers[2 * k].len = sizeof(st->scan_tx_reset);
+ spi_message_add_tail(&st->scan_xfers[2 * k], &st->scan_msg);
+
+ ret = spi_optimize_message(st->spi, &st->scan_msg);
+ if (ret)
+ return ret;
+
+ std_seq_config = bitmap_read(indio_dev->active_scan_mask, 0,
+ iio_get_masklength(indio_dev)) & GENMASK(15, 0);
+ ret = regmap_write(st->regmap, AD4691_STD_SEQ_CONFIG, std_seq_config);
+ if (ret)
+ goto err_unoptimize;
+
+ acc_mask = ~std_seq_config & GENMASK(15, 0);
+ ret = regmap_write(st->regmap, AD4691_ACC_MASK_REG, acc_mask);
+ if (ret)
+ goto err_unoptimize;
+
+ ret = ad4691_enter_conversion_mode(st);
+ if (ret)
+ goto err_unoptimize;
+
+ return 0;
+
+err_unoptimize:
+ spi_unoptimize_message(&st->scan_msg);
+ return ret;
+}
+
+static int ad4691_cnv_burst_buffer_postenable(struct iio_dev *indio_dev)
+{
+ struct ad4691_state *st = iio_priv(indio_dev);
+ int ret;
+
+ /*
+ * Start the PWM and unmask the IRQ here in postenable, not in
+ * preenable. The IIO core attaches the trigger poll function between
+ * preenable and postenable; enabling sampling or unmasking the IRQ
+ * before that point risks a DATA_READY assertion landing before the
+ * poll function is registered. iio_trigger_poll() would drop the
+ * event, disable_irq_nosync() would fire, and enable_irq() would
+ * never be called, leaving the IRQ permanently masked.
+ */
+ ret = ad4691_sampling_enable(st, true);
+ if (ret)
+ return ret;
+
+ enable_irq(st->irq);
+ st->irq_enabled = true;
+ return 0;
+}
+
+static int ad4691_cnv_burst_buffer_predisable(struct iio_dev *indio_dev)
+{
+ struct ad4691_state *st = iio_priv(indio_dev);
+
+ if (st->irq_enabled) {
+ disable_irq(st->irq);
+ st->irq_enabled = false;
+ }
+ return ad4691_sampling_enable(st, false);
+}
+
+static int ad4691_cnv_burst_buffer_postdisable(struct iio_dev *indio_dev)
+{
+ struct ad4691_state *st = iio_priv(indio_dev);
+ int ret;
+
+ ret = ad4691_exit_conversion_mode(st);
+ spi_unoptimize_message(&st->scan_msg);
+ return ret;
+}
+
+static const struct iio_buffer_setup_ops ad4691_cnv_burst_buffer_setup_ops = {
+ .preenable = ad4691_cnv_burst_buffer_preenable,
+ .postenable = ad4691_cnv_burst_buffer_postenable,
+ .predisable = ad4691_cnv_burst_buffer_predisable,
+ .postdisable = ad4691_cnv_burst_buffer_postdisable,
+};
+
+static ssize_t sampling_frequency_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+ struct ad4691_state *st = iio_priv(indio_dev);
+
+ return sysfs_emit(buf, "%lu\n", NSEC_PER_SEC / st->cnv_period_ns);
+}
+
+static ssize_t sampling_frequency_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t len)
+{
+ struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+ struct ad4691_state *st = iio_priv(indio_dev);
+ unsigned int freq;
+ int ret;
+
+ ret = kstrtouint(buf, 10, &freq);
+ if (ret)
+ return ret;
+
+ IIO_DEV_ACQUIRE_DIRECT_MODE(indio_dev, claim);
+ if (IIO_DEV_ACQUIRE_FAILED(claim))
+ return -EBUSY;
+
+ ret = ad4691_set_pwm_freq(st, freq);
+ if (ret)
+ return ret;
+
+ return len;
+}
+
+static IIO_DEVICE_ATTR_RW(sampling_frequency, 0);
+
+static const struct iio_dev_attr *ad4691_buffer_attrs[] = {
+ &iio_dev_attr_sampling_frequency,
+ NULL
+};
+
+static irqreturn_t ad4691_irq(int irq, void *private)
+{
+ struct iio_dev *indio_dev = private;
+ struct ad4691_state *st = iio_priv(indio_dev);
+
+ /*
+ * Disable the IRQ before calling iio_trigger_poll(). The IRQ is
+ * re-enabled via the trigger .reenable callback, which the IIO core
+ * calls inside iio_trigger_notify_done() once use_count reaches zero.
+ * Re-enabling here (before notify_done) would race: a DATA_READY
+ * between enable_irq() and notify_done() calls iio_trigger_poll()
+ * while use_count > 0, dropping the event and permanently masking
+ * the IRQ.
+ */
+ disable_irq_nosync(st->irq);
+ iio_trigger_poll(indio_dev->trig);
+
+ return IRQ_HANDLED;
+}
+
+static void ad4691_trigger_reenable(struct iio_trigger *trig)
+{
+ struct ad4691_state *st = iio_trigger_get_drvdata(trig);
+
+ enable_irq(st->irq);
+}
+
+static const struct iio_trigger_ops ad4691_trigger_ops = {
+ .reenable = ad4691_trigger_reenable,
+ .validate_device = iio_trigger_validate_own_device,
+};
+
+static void ad4691_read_scan(struct iio_dev *indio_dev, s64 ts)
+{
+ struct ad4691_state *st = iio_priv(indio_dev);
+ int ret;
+
+ guard(mutex)(&st->lock);
+
+ ret = spi_sync(st->spi, &st->scan_msg);
+ if (ret) {
+ dev_err_ratelimited(regmap_get_device(st->regmap),
+ "SPI scan failed: %d\n", ret);
+ return;
+ }
+
+ /*
+ * rx_buf pointers in scan_xfers point directly into scan.vals, so no
+ * copy is needed. The scan_msg already includes a STATE_RESET at the
+ * end (appended in preenable), so no explicit reset is needed here.
+ */
+ iio_push_to_buffers_with_ts(indio_dev, st->vals, sizeof(st->vals), ts);
+}
+
+static irqreturn_t ad4691_trigger_handler(int irq, void *p)
+{
+ struct iio_poll_func *pf = p;
+ struct iio_dev *indio_dev = pf->indio_dev;
+
+ ad4691_read_scan(indio_dev, pf->timestamp);
+ iio_trigger_notify_done(indio_dev->trig);
+ return IRQ_HANDLED;
+}
+
+/*
+ * CNV burst mode: only allow our own trigger (driven by DATA_READY IRQ).
+ * Manual mode: external triggers (e.g. iio-trig-hrtimer) must be allowed
+ * because manual mode has no DATA_READY IRQ to fire the internal trigger.
+ * iio_trigger_ops.validate_device = iio_trigger_validate_own_device is
+ * correct in both modes — it prevents other devices from hijacking our
+ * internal trigger; the distinction here is only for iio_info.validate_trigger.
+ */
+static const struct iio_info ad4691_cnv_burst_info = {
.read_raw = ad4691_read_raw,
.write_raw = ad4691_write_raw,
.read_avail = ad4691_read_avail,
.debugfs_reg_access = ad4691_reg_access,
+ .validate_trigger = iio_validate_own_trigger,
};
+static const struct iio_info ad4691_manual_info = {
+ .read_raw = ad4691_read_raw,
+ .write_raw = ad4691_write_raw,
+ .read_avail = ad4691_read_avail,
+ .debugfs_reg_access = ad4691_reg_access,
+};
+
+static int ad4691_pwm_setup(struct ad4691_state *st)
+{
+ struct device *dev = regmap_get_device(st->regmap);
+
+ st->conv_trigger = devm_pwm_get(dev, "cnv");
+ if (IS_ERR(st->conv_trigger))
+ return dev_err_probe(dev, PTR_ERR(st->conv_trigger),
+ "Failed to get CNV PWM\n");
+
+ return ad4691_set_pwm_freq(st, st->info->max_rate);
+}
+
static int ad4691_regulator_setup(struct ad4691_state *st)
{
struct device *dev = regmap_get_device(st->regmap);
unsigned int val;
int ret;
+ /*
+ * Determine buffer conversion mode from DT: if a PWM is provided it
+ * drives the CNV pin (CNV_BURST_MODE); otherwise CNV is tied to CS
+ * and each SPI transfer triggers a conversion (MANUAL_MODE).
+ * Both modes idle in AUTONOMOUS mode so that read_raw can use the
+ * internal oscillator without disturbing the hardware configuration.
+ */
+ if (device_property_present(dev, "pwms")) {
+ st->manual_mode = false;
+ ret = ad4691_pwm_setup(st);
+ if (ret)
+ return ret;
+ } else {
+ st->manual_mode = true;
+ }
+
switch (st->vref_uV) {
case AD4691_VREF_uV_MIN ... AD4691_VREF_2P5_uV_MAX:
ref_val = AD4691_VREF_2P5;
return 0;
}
+static int ad4691_setup_triggered_buffer(struct iio_dev *indio_dev,
+ struct ad4691_state *st)
+{
+ struct device *dev = regmap_get_device(st->regmap);
+ struct iio_trigger *trig;
+ unsigned int i;
+ int irq, ret;
+
+ indio_dev->channels = st->info->sw_info->channels;
+ indio_dev->num_channels = st->info->sw_info->num_channels;
+ indio_dev->info = st->manual_mode ? &ad4691_manual_info : &ad4691_cnv_burst_info;
+
+ /*
+ * Manual mode relies on an external trigger (e.g. iio-trig-hrtimer);
+ * no internal trigger is needed or registered.
+ */
+ if (st->manual_mode)
+ return devm_iio_triggered_buffer_setup(dev, indio_dev,
+ iio_pollfunc_store_time,
+ ad4691_trigger_handler,
+ &ad4691_manual_buffer_setup_ops);
+
+ /*
+ * CNV burst mode: allocate an internal trigger driven by the
+ * DATA_READY IRQ on the GP pin.
+ */
+ trig = devm_iio_trigger_alloc(dev, "%s-dev%d", indio_dev->name,
+ iio_device_id(indio_dev));
+ if (!trig)
+ return -ENOMEM;
+
+ trig->ops = &ad4691_trigger_ops;
+ iio_trigger_set_drvdata(trig, st);
+
+ ret = devm_iio_trigger_register(dev, trig);
+ if (ret)
+ return dev_err_probe(dev, ret, "IIO trigger register failed\n");
+
+ indio_dev->trig = iio_trigger_get(trig);
+
+ /*
+ * The GP pin named in interrupt-names asserts at end-of-conversion.
+ * The IRQ handler fires the IIO trigger so the trigger handler can
+ * read and push the sample to the buffer. The IRQ is kept disabled
+ * until the buffer is enabled.
+ */
+ irq = -ENXIO;
+ for (i = 0; i < ARRAY_SIZE(ad4691_gp_names); i++) {
+ irq = fwnode_irq_get_byname(dev_fwnode(dev),
+ ad4691_gp_names[i]);
+ if (irq > 0 || irq == -EPROBE_DEFER)
+ break;
+ }
+ if (irq < 0)
+ return dev_err_probe(dev, irq, "failed to get GP interrupt\n");
+
+ st->irq = irq;
+
+ ret = ad4691_gpio_setup(st, i);
+ if (ret)
+ return ret;
+
+ /*
+ * The handler only calls disable_irq_nosync() and iio_trigger_poll(),
+ * both safe in hardirq context, so register as a hard IRQ handler.
+ * IRQF_NO_AUTOEN keeps it disabled until the buffer is enabled.
+ */
+ ret = devm_request_irq(dev, irq, ad4691_irq, IRQF_NO_AUTOEN,
+ indio_dev->name, indio_dev);
+ if (ret)
+ return ret;
+
+ return devm_iio_triggered_buffer_setup_ext(dev, indio_dev,
+ iio_pollfunc_store_time,
+ ad4691_trigger_handler,
+ IIO_BUFFER_DIRECTION_IN,
+ &ad4691_cnv_burst_buffer_setup_ops,
+ ad4691_buffer_attrs);
+}
+
static int ad4691_probe(struct spi_device *spi)
{
struct device *dev = &spi->dev;
return ret;
indio_dev->name = st->info->name;
- indio_dev->info = &ad4691_info;
indio_dev->modes = INDIO_DIRECT_MODE;
- indio_dev->channels = st->info->sw_info->channels;
- indio_dev->num_channels = st->info->sw_info->num_channels;
+ ret = ad4691_setup_triggered_buffer(indio_dev, st);
+ if (ret)
+ return ret;
return devm_iio_device_register(dev, indio_dev);
}
projects / thirdparty / kernel / linux.git / commitdiff
