Merge tag 'qcom-arm64-for-6.20' of https://git.kernel.org/pub/scm/linux/kernel/git...

Qualcomm Arm64 DeviceTree for v6.20

Introduce the Kaanapali SoC, with the MTP and QRD devices. Introduce
support for the Milos SoC (SM7635) and initial support for the Fairphone
(Gen 6) device on this platform.

Add the QCS6490-based RubikPI3 board, the QRB2210-based Arduino UnoQ,
the X Elite-based Medion SPRCHRGD 14 S1 and Surface Pro 11 laptops, and
the SDM845-based Pixel 3 and Pixel 3 XL devices.

On the Kodiak-based (QCS6490) RB3Gen2 the TC9563 PCIe switch controller
is described.

On Lemans (SA8775P/QCS9075) the GPU and crypto blocks are added.
IO-regions and clocks are added to interconnect nodes to allow QoS
configuration. GPU, TPM and USB support are enabled on the evaluation
kit (EVK).

On Monaco (QCS8300) the two PCIe controllers, the camera subsystem,
tsens, display subsystem, crypto, CPUfreq, and coresight are added. On
the evaluation kit (EVK) the PCIe busses are enabled, together with an
AMC6821-based fan controller and the ST33 TPM chip.

On MSM8939 the camera subsystem is described. The Asus ZenFone 2
Laser/Selfie gains battery and hall sensor support.

On the Agatti-based RB1 board PM8008 is described and an overlay for the
Vision mezzanine is introduced.

On SDM630 the compute DSP remoteproc, FastRPC and related entites are
described. The LPASS LPI pinctrl node is described.

On SDM845-based OnePlus device the bootloader framebuffer and its
resources are described, to improve the transition. On the SDM845-based
devices from OnePlus, SHIFT, and Xiaomi ath10k calibration variants are
specified. The sensor remoteproc is enabled on Xiaomi Pocophone F1.

On SM7225-based Fairphone FP4 regulators for the cameras are described,
and the camera EEPROM is added.

On SM8650 the camera subsystem is described. On the QRD the Samsung
S5KJN1 camera sensor is added, and for the HDK an overlay for the "Rear
Camera Card" is added.

On SM8750 CPUfreq, SDCHCI and Iris (video encode/decode) support are
added, and missing - required - properties for the BAM DMA is added.
These are then enabled on the MTP.

On Talos (SM6150/QCS615) PMU, DisplayPort, and USB/DP combo PHY are added.
DisplayPort is enabled on the Talos Ride board.

On Hamoa (X Elite) add crypto engine, missing TCSR reference clocks, and
random number generator block. The soc bus address width is corrected to
match the hardware. On the Lenovo Thinkpad T14s HDMI and audio playback
over DisplayPort is introduced. HDMI, Iris (video encode/decode) and
PS8830 retimers are described for the ASUS Vivobook S 15. On the Hamoa
evaluation kit (EVK) PCIe busses, WiFi, backlight, TPM and RG
(red/green) LEDs are described.

Enable QSEECOM, and thereby UEFI variable access, on the Medion SPRCHRGD
14 S1 (commit should have been on drivers branch).

* tag 'qcom-arm64-for-6.20' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (155 commits)
  dt-bindings: mailbox: qcom: Add IPCC support for Kaanapali and Glymur Platforms
  dt-bindings: mailbox: qcom: Add CPUCP mailbox controller bindings for Kaanapali
  arm64: dts: qcom: lemans: enable static TPDM
  arm64: dts: qcom: kodiak: Add memory region for audiopd
  arm64: dts: qcom: x1e78100-lenovo-thinkpad-t14s: add HDMI nodes
  arm64: dts: qcom: x1e: bus is 40-bits (fix 64GB models)
  arm64: dts: qcom: lemans; Add EL2 overlay
  arm64: dts: qcom: sm8150: add uart13
  arm64: dts: qcom: sdm845-db845c: specify power for WiFi CH1
  arm64: dts: qcom: sdm845-db845c: drop CS from SPIO0
  arm64: dts: qcom: qrb4210-rb2: Fix UART3 wakeup IRQ storm
  arm64: dts: qcom: sm6125-ginkgo: Fix missing msm-id subtype
  arm64: dts: qcom: qcs8300: Add GPU cooling
  arm64: dts: qcom: sa8775p: Add reg and clocks for QoS configuration
  arm64: dts: qcom: hamoa-iot-evk: Enable TPM (ST33) on SPI11
  arm64: dts: qcom: talos: Add PMU support
  arm64: dts: qcom: talos: switch to interrupt-cells 4 to add PPI partitions
  arm64: dts: qcom: ipq9574: Complete USB DWC3 wrapper interrupts
  arm64: dts: qcom: ipq5018: Correct USB DWC3 wrapper interrupts
  arm64: dts: qcom: monaco: Add CTCU and ETR nodes
  ...

Signed-off-by: Arnd Bergmann <arnd@arndb.de>