TP-Link EAP625-Outdoor HD is a 802.11ax AP claiming AX1800 support.
It is wall or pole mountable, and rated for outdoor use. It can only
be powered via PoE.
Hardware-wise, it is very similar to the older EAP610-Outdoor model.
Software-wise, I couldn't find a difference other than the board
data files, and device name. For this reason, the majority of the
devicetree from the EAP610-Outdoor is reused.
This device currently comes in a "v1", and "v1.6" version. The
"support-list" of the vendor firmware does not have a distinction
between these versions. This commit was tested on a 'V1.6" device.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
NOTE: If ssh continues to complain that "no matching host key type
found. Their offer: ssh-rsa,ssh-dss" it likely means that yor distro
has completely disabled deprecated siphers in ssh. In that case, run
the ssh command from a docker container of an older distro.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap625-outdoor-hd-v1-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
netgear,wax610|\
netgear,wax610y|\
tplink,eap610-outdoor|\
-tplink,eap623od-hd-v1)
+tplink,eap623od-hd-v1|\
+tplink,eap625-outdoor-hd-v1)
ubootenv_add_mtd "0:appsblenv" "0x0" "0x40000" "0x20000"
;;
yuncore,fap650)
PKG_SOURCE_PROTO:=git
PKG_SOURCE_URL=$(PROJECT_GIT)/project/firmware/qca-wireless.git
-PKG_SOURCE_DATE:=2025-04-22
-PKG_SOURCE_VERSION:=acf37292d2c1c27930b4d9ba58276b599706910d
-PKG_MIRROR_HASH:=1068b8ea938bfb0cd72bd48ef329e885a283e91f2ae864bfba9171c729e3d308
+PKG_SOURCE_DATE:=2025-05-13
+PKG_SOURCE_VERSION:=dae5a57ea2c28eea409c51cdcb1b57ecbb366a26
+PKG_MIRROR_HASH:=9a9a63cc41a8d992658149bf6a6dd2287d022cd8829a4c4a62a4a4449c88f31a
PKG_FLAGS:=nonshared
include $(INCLUDE_DIR)/package.mk
tplink_eap610-outdoor \
tplink_eap620hd-v1 \
tplink_eap623od-hd-v1 \
+ tplink_eap625-outdoor-hd-v1 \
tplink_eap660hd-v1 \
wallys_dr40x9 \
xiaomi_ax3600 \
$(eval $(call generate-ipq-wifi-package,tplink_eap610-outdoor,TPLink EAP610-Outdoor))
$(eval $(call generate-ipq-wifi-package,tplink_eap620hd-v1,TP-Link EAP620 HD v1))
$(eval $(call generate-ipq-wifi-package,tplink_eap623od-hd-v1,TP-Link EAP623-Outdoor HD v1))
+$(eval $(call generate-ipq-wifi-package,tplink_eap625-outdoor-hd-v1,TP-Link EAP625-Outdoor HD v1))
$(eval $(call generate-ipq-wifi-package,tplink_eap660hd-v1,TP-Link EAP660 HD v1))
$(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9))
$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "ipq6018-tplink-eap6xx-outdoor.dtsi"
+
+/ {
+ model = "TP-Link EAP625-Outdoor HD v1";
+ compatible = "tplink,eap625-outdoor-hd-v1", "qcom,ipq6018";
+};
+
+&wifi {
+ qcom,ath11k-calibration-variant = "TP-Link-EAP625-Outdoor-HD-v1";
+};
endef
TARGET_DEVICES += tplink_eap623od-hd-v1
+define Device/tplink_eap625-outdoor-hd-v1
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := TP-Link
+ DEVICE_MODEL := EAP625-Outdoor HD v1 and v1.6
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ SOC := ipq6018
+ DEVICE_PACKAGES := ipq-wifi-tplink_eap625-outdoor
+ IMAGES += web-ui-factory.bin
+ IMAGE/web-ui-factory.bin := append-ubi | tplink-image-2022
+ TPLINK_SUPPORT_STRING := SupportList:\r\n \
+ EAP625-Outdoor HD(TP-Link|UN|AX1800-D):1.0\r\n \
+ EAP625-Outdoor HD(TP-Link|CA|AX1800-D):1.0\r\n \
+ EAP625-Outdoor HD(TP-Link|AU|AX1800-D):1.0\r\n \
+ EAP625-Outdoor HD(TP-Link|KR|AX1800-D):1.0
+
+endef
+TARGET_DEVICES += tplink_eap625-outdoor-hd-v1
+
define Device/yuncore_fap650
$(call Device/FitImage)
$(call Device/UbiFit)
netgear,wax610|\
netgear,wax610y|\
tplink,eap610-outdoor|\
- tplink,eap623od-hd-v1)
+ tplink,eap623od-hd-v1|\
+ tplink,eap625-outdoor-hd-v1)
ucidef_set_interface_lan "lan" "dhcp"
;;
*)
label_mac=$lan_mac
;;
tplink,eap610-outdoor|\
- tplink,eap623od-hd-v1)
+ tplink,eap623od-hd-v1|\
+ tplink,eap625-outdoor-hd-v1)
label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0)
lan_mac=$label_mac
;;
ath11k_set_macflag
;;
tplink,eap610-outdoor|\
- tplink,eap623od-hd-v1)
+ tplink,eap623od-hd-v1|\
+ tplink,eap625-outdoor-hd-v1)
caldata_from_file "/tmp/factory_data/radio" 0 0x10000
label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0)
ath11k_patch_mac $label_mac 1
case $(board_name) in
tplink,eap610-outdoor|\
- tplink,eap623od-hd-v1)
+ tplink,eap623od-hd-v1|\
+ tplink,eap625-outdoor-hd-v1)
mtd_path=$(find_mtd_chardev "factory_data")
ubiattach --dev-path="$mtd_path" --devn=1
mkdir /tmp/factory_data
nand_do_upgrade "$1"
;;
tplink,eap610-outdoor|\
- tplink,eap623od-hd-v1)
+ tplink,eap623od-hd-v1|\
+ tplink,eap625-outdoor-hd-v1)
tplink_do_upgrade "$1"
;;
yuncore,fap650)
projects / thirdparty / openwrt.git / commitdiff
