i2c: qcom-geni: Correct I2C TRE sequence

[ Upstream commit 83ef106fa732aea8558253641cd98e8a895604d7 ]

For i2c read operation in GSI mode, we are getting timeout
due to malformed TRE basically incorrect TRE sequence
in gpi(drivers/dma/qcom/gpi.c) driver.

I2C driver has geni_i2c_gpi(I2C_WRITE) function which generates GO TRE and
geni_i2c_gpi(I2C_READ)generates DMA TRE. Hence to generate GO TRE before
DMA TRE, we should move geni_i2c_gpi(I2C_WRITE) before
geni_i2c_gpi(I2C_READ) inside the I2C GSI mode transfer function
i.e. geni_i2c_gpi_xfer().

TRE stands for Transfer Ring Element - which is basically an element with
size of 4 words. It contains all information like slave address,
clk divider, dma address value data size etc).

Mainly we have 3 TREs(Config, GO and DMA tre).
- CONFIG TRE : consists of internal register configuration which is
               required before start of the transfer.
- DMA TRE :    contains DDR/Memory address, called as DMA descriptor.
- GO TRE :     contains Transfer directions, slave ID, Delay flags, Length
               of the transfer.

I2c driver calls GPI driver API to config each TRE depending on the
protocol.

For read operation tre sequence will be as below which is not aligned
to hardware programming guide.

- CONFIG tre
- DMA tre
- GO tre

As per Qualcomm's internal Hardware Programming Guide, we should configure
TREs in below sequence for any RX only transfer.

- CONFIG tre
- GO tre
- DMA tre

Fixes: d8703554f4de ("i2c: qcom-geni: Add support for GPI DMA")
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # qrb5165-rb5
Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
index 0d2e7171e3a6f94a66d2ff85861723e0f2caea00..da94df466e83c9d34c6212681c087cafc8a6b788 100644 (file)
--- a/drivers/i2c/busses/i2c-qcom-geni.c
+++ b/drivers/i2c/busses/i2c-qcom-geni.c
@@ -613,20 +613,20 @@ static int geni_i2c_gpi_xfer(struct geni_i2c_dev *gi2c, struct i2c_msg msgs[], i
 
                peripheral.addr = msgs[i].addr;
 
+               ret =  geni_i2c_gpi(gi2c, &msgs[i], &config,
+                                   &tx_addr, &tx_buf, I2C_WRITE, gi2c->tx_c);
+               if (ret)
+                       goto err;
+
                if (msgs[i].flags & I2C_M_RD) {
                        ret =  geni_i2c_gpi(gi2c, &msgs[i], &config,
                                            &rx_addr, &rx_buf, I2C_READ, gi2c->rx_c);
                        if (ret)
                                goto err;
-               }
-
-               ret =  geni_i2c_gpi(gi2c, &msgs[i], &config,
-                                   &tx_addr, &tx_buf, I2C_WRITE, gi2c->tx_c);
-               if (ret)
-                       goto err;
 
-               if (msgs[i].flags & I2C_M_RD)
                        dma_async_issue_pending(gi2c->rx_c);
+               }
+
                dma_async_issue_pending(gi2c->tx_c);
 
                timeout = wait_for_completion_timeout(&gi2c->done, XFER_TIMEOUT);