return 0;
}
+static void rtl8192cu_power_off(struct rtl8xxxu_priv *priv)
+{
+ u32 val32;
+ u16 val16;
+ u8 val8;
+ int i;
+
+ /*
+ * Workaround for 8188RU LNA power leakage problem.
+ */
+ if (priv->rtl_chip == RTL8188R) {
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_XCD_RF_PARM);
+ val32 |= BIT(1);
+ rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_PARM, val32);
+ }
+
+ /* _DisableRFAFEAndResetBB */
+ rtl8xxxu_write8(priv, REG_TXPAUSE, 0xff);
+ rtl8xxxu_write_rfreg_mask(priv, RF_A, RF6052_REG_AC, 0xff, 0);
+
+ rtl8xxxu_write8_set(priv, REG_APSD_CTRL, APSD_CTRL_OFF);
+ rtl8xxxu_write32_set(priv, REG_FPGA0_XCD_RF_PARM, FPGA0_RF_PARM_CLK_GATE);
+
+ rtl8xxxu_write8(priv, REG_SYS_FUNC,
+ SYS_FUNC_USBA | SYS_FUNC_USBD | SYS_FUNC_BB_GLB_RSTN);
+ rtl8xxxu_write8(priv, REG_SYS_FUNC, SYS_FUNC_USBA | SYS_FUNC_USBD);
+
+ /* _ResetDigitalProcedure1 */
+ if (rtl8xxxu_read8(priv, REG_MCU_FW_DL) & MCU_FW_DL_READY) {
+ rtl8xxxu_write8(priv, REG_MCU_FW_DL, 0x00);
+
+ rtl8xxxu_write8(priv, REG_FWIMR, 0x20);
+
+ rtl8xxxu_write8(priv, REG_HMTFR + 3, 0x20);
+
+ for (i = 0; i < 100; i++) {
+ val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
+ if (!(val16 & SYS_FUNC_CPU_ENABLE))
+ break;
+
+ fsleep(50);
+ }
+
+ if (i == 100) {
+ rtl8xxxu_write8(priv, REG_SYS_FUNC + 1,
+ (SYS_FUNC_HWPDN | SYS_FUNC_ELDR) >> 8);
+ msleep(10);
+ }
+ }
+
+ val8 = (SYS_FUNC_HWPDN | SYS_FUNC_ELDR | SYS_FUNC_CPU_ENABLE) >> 8;
+ rtl8xxxu_write8(priv, REG_SYS_FUNC + 1, val8);
+
+ /* _DisableGPIO */
+ rtl8xxxu_write16(priv, REG_GPIO_PIN_CTRL + 2, 0);
+ val32 = rtl8xxxu_read32(priv, REG_GPIO_PIN_CTRL) & 0xffff00ff;
+ val32 |= (val32 & 0xff) << 8;
+ val32 |= 0x00ff0000;
+ rtl8xxxu_write32(priv, REG_GPIO_PIN_CTRL, val32);
+
+ rtl8xxxu_write8(priv, REG_GPIO_MUXCFG + 3, 0);
+ val16 = rtl8xxxu_read16(priv, REG_GPIO_MUXCFG + 2) & 0xff0f;
+ val16 |= (val16 & 0xf) << 4;
+ val16 |= 0x0780;
+ rtl8xxxu_write16(priv, REG_GPIO_MUXCFG + 2, val16);
+
+ /* _DisableAnalog */
+ val8 = 0x23;
+ if (priv->vendor_umc && priv->chip_cut == 1)
+ val8 |= BIT(3);
+ rtl8xxxu_write8(priv, REG_SPS0_CTRL, val8);
+
+ val16 = APS_FSMCO_HOST | APS_FSMCO_HW_SUSPEND | APS_FSMCO_PFM_ALDN;
+ rtl8xxxu_write16(priv, REG_APS_FSMCO, val16);
+
+ rtl8xxxu_write8(priv, REG_RSV_CTRL, 0x0e);
+}
+
static int rtl8192cu_led_brightness_set(struct led_classdev *led_cdev,
enum led_brightness brightness)
{
.parse_efuse = rtl8192cu_parse_efuse,
.load_firmware = rtl8192cu_load_firmware,
.power_on = rtl8192cu_power_on,
- .power_off = rtl8xxxu_power_off,
+ .power_off = rtl8192cu_power_off,
.read_efuse = rtl8xxxu_read_efuse,
.reset_8051 = rtl8xxxu_reset_8051,
.llt_init = rtl8xxxu_init_llt_table,
return ret;
}
+static int rtl8723au_active_to_emu(struct rtl8xxxu_priv *priv)
+{
+ u8 val8;
+ int count, ret = 0;
+
+ /* Start of rtl8723AU_card_enable_flow */
+ /* Act to Cardemu sequence*/
+ /* Turn off RF */
+ rtl8xxxu_write8(priv, REG_RF_CTRL, 0);
+
+ /* 0x004E[7] = 0, switch DPDT_SEL_P output from register 0x0065[2] */
+ val8 = rtl8xxxu_read8(priv, REG_LEDCFG2);
+ val8 &= ~LEDCFG2_DPDT_SELECT;
+ rtl8xxxu_write8(priv, REG_LEDCFG2, val8);
+
+ /* 0x0005[1] = 1 turn off MAC by HW state machine*/
+ val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
+ val8 |= BIT(1);
+ rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
+
+ for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
+ val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
+ if ((val8 & BIT(1)) == 0)
+ break;
+ udelay(10);
+ }
+
+ if (!count) {
+ dev_warn(&priv->udev->dev, "%s: Disabling MAC timed out\n",
+ __func__);
+ ret = -EBUSY;
+ goto exit;
+ }
+
+ /* 0x0000[5] = 1 analog Ips to digital, 1:isolation */
+ val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL);
+ val8 |= SYS_ISO_ANALOG_IPS;
+ rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8);
+
+ /* 0x0020[0] = 0 disable LDOA12 MACRO block*/
+ val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL);
+ val8 &= ~LDOA15_ENABLE;
+ rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8);
+
+exit:
+ return ret;
+}
+
+static int rtl8723au_emu_to_disabled(struct rtl8xxxu_priv *priv)
+{
+ u8 val8;
+
+ /* 0x0007[7:0] = 0x20 SOP option to disable BG/MB */
+ rtl8xxxu_write8(priv, REG_APS_FSMCO + 3, 0x20);
+
+ /* 0x04[12:11] = 01 enable WL suspend */
+ val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
+ val8 &= ~BIT(4);
+ val8 |= BIT(3);
+ rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
+
+ val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
+ val8 |= BIT(7);
+ rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
+
+ /* 0x48[16] = 1 to enable GPIO9 as EXT wakeup */
+ val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 2);
+ val8 |= BIT(0);
+ rtl8xxxu_write8(priv, REG_GPIO_INTM + 2, val8);
+
+ return 0;
+}
+
+static void rtl8723au_power_off(struct rtl8xxxu_priv *priv)
+{
+ u8 val8;
+ u16 val16;
+
+ rtl8xxxu_flush_fifo(priv);
+
+ rtl8xxxu_active_to_lps(priv);
+
+ /* Turn off RF */
+ rtl8xxxu_write8(priv, REG_RF_CTRL, 0x00);
+
+ /* Reset Firmware if running in RAM */
+ if (rtl8xxxu_read8(priv, REG_MCU_FW_DL) & MCU_FW_RAM_SEL)
+ rtl8xxxu_firmware_self_reset(priv);
+
+ /* Reset MCU */
+ val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
+ val16 &= ~SYS_FUNC_CPU_ENABLE;
+ rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
+
+ /* Reset MCU ready status */
+ rtl8xxxu_write8(priv, REG_MCU_FW_DL, 0x00);
+
+ rtl8723au_active_to_emu(priv);
+ rtl8723au_emu_to_disabled(priv);
+
+ /* Reset MCU IO Wrapper */
+ val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
+ val8 &= ~BIT(0);
+ rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
+
+ val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
+ val8 |= BIT(0);
+ rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
+
+ /* RSV_CTRL 0x1C[7:0] = 0x0e lock ISO/CLK/Power control register */
+ rtl8xxxu_write8(priv, REG_RSV_CTRL, 0x0e);
+}
+
#define XTAL1 GENMASK(23, 18)
#define XTAL0 GENMASK(17, 12)
.parse_efuse = rtl8723au_parse_efuse,
.load_firmware = rtl8723au_load_firmware,
.power_on = rtl8723au_power_on,
- .power_off = rtl8xxxu_power_off,
+ .power_off = rtl8723au_power_off,
.read_efuse = rtl8xxxu_read_efuse,
.reset_8051 = rtl8xxxu_reset_8051,
.llt_init = rtl8xxxu_init_llt_table,
rtl8xxxu_write8(priv, REG_AMPDU_MIN_SPACE, val8);
}
-static int rtl8xxxu_active_to_emu(struct rtl8xxxu_priv *priv)
-{
- u8 val8;
- int count, ret = 0;
-
- /* Start of rtl8723AU_card_enable_flow */
- /* Act to Cardemu sequence*/
- /* Turn off RF */
- rtl8xxxu_write8(priv, REG_RF_CTRL, 0);
-
- /* 0x004E[7] = 0, switch DPDT_SEL_P output from register 0x0065[2] */
- val8 = rtl8xxxu_read8(priv, REG_LEDCFG2);
- val8 &= ~LEDCFG2_DPDT_SELECT;
- rtl8xxxu_write8(priv, REG_LEDCFG2, val8);
-
- /* 0x0005[1] = 1 turn off MAC by HW state machine*/
- val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
- val8 |= BIT(1);
- rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
-
- for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
- val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
- if ((val8 & BIT(1)) == 0)
- break;
- udelay(10);
- }
-
- if (!count) {
- dev_warn(&priv->udev->dev, "%s: Disabling MAC timed out\n",
- __func__);
- ret = -EBUSY;
- goto exit;
- }
-
- /* 0x0000[5] = 1 analog Ips to digital, 1:isolation */
- val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL);
- val8 |= SYS_ISO_ANALOG_IPS;
- rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8);
-
- /* 0x0020[0] = 0 disable LDOA12 MACRO block*/
- val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL);
- val8 &= ~LDOA15_ENABLE;
- rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8);
-
-exit:
- return ret;
-}
-
int rtl8xxxu_active_to_lps(struct rtl8xxxu_priv *priv)
{
u8 val8;
rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
}
-static int rtl8xxxu_emu_to_disabled(struct rtl8xxxu_priv *priv)
-{
- u8 val8;
-
- /* 0x0007[7:0] = 0x20 SOP option to disable BG/MB */
- rtl8xxxu_write8(priv, REG_APS_FSMCO + 3, 0x20);
-
- /* 0x04[12:11] = 01 enable WL suspend */
- val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
- val8 &= ~BIT(4);
- val8 |= BIT(3);
- rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
-
- val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
- val8 |= BIT(7);
- rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
-
- /* 0x48[16] = 1 to enable GPIO9 as EXT wakeup */
- val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 2);
- val8 |= BIT(0);
- rtl8xxxu_write8(priv, REG_GPIO_INTM + 2, val8);
-
- return 0;
-}
-
int rtl8xxxu_flush_fifo(struct rtl8xxxu_priv *priv)
{
struct device *dev = &priv->udev->dev;
rtl8xxxu_write32(priv, REG_TXDMA_OFFSET_CHK, val32);
}
-void rtl8xxxu_power_off(struct rtl8xxxu_priv *priv)
-{
- u8 val8;
- u16 val16;
- u32 val32;
-
- /*
- * Workaround for 8188RU LNA power leakage problem.
- */
- if (priv->rtl_chip == RTL8188R) {
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_XCD_RF_PARM);
- val32 |= BIT(1);
- rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_PARM, val32);
- }
-
- rtl8xxxu_flush_fifo(priv);
-
- rtl8xxxu_active_to_lps(priv);
-
- /* Turn off RF */
- rtl8xxxu_write8(priv, REG_RF_CTRL, 0x00);
-
- /* Reset Firmware if running in RAM */
- if (rtl8xxxu_read8(priv, REG_MCU_FW_DL) & MCU_FW_RAM_SEL)
- rtl8xxxu_firmware_self_reset(priv);
-
- /* Reset MCU */
- val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
- val16 &= ~SYS_FUNC_CPU_ENABLE;
- rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
-
- /* Reset MCU ready status */
- rtl8xxxu_write8(priv, REG_MCU_FW_DL, 0x00);
-
- rtl8xxxu_active_to_emu(priv);
- rtl8xxxu_emu_to_disabled(priv);
-
- /* Reset MCU IO Wrapper */
- val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
- val8 &= ~BIT(0);
- rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
-
- val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
- val8 |= BIT(0);
- rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
-
- /* RSV_CTRL 0x1C[7:0] = 0x0e lock ISO/CLK/Power control register */
- rtl8xxxu_write8(priv, REG_RSV_CTRL, 0x0e);
-}
-
void rtl8723bu_set_ps_tdma(struct rtl8xxxu_priv *priv,
u8 arg1, u8 arg2, u8 arg3, u8 arg4, u8 arg5)
{
#define APS_FSMCO_SW_LPS BIT(10)
#define APS_FSMCO_HW_SUSPEND BIT(11)
#define APS_FSMCO_PCIE BIT(12)
+#define APS_FSMCO_HOST BIT(14)
#define APS_FSMCO_HW_POWERDOWN BIT(15)
#define APS_FSMCO_WLON_RESET BIT(16)
const struct rtl8xxxu_reg32val *array);
int rtl8xxxu_load_firmware(struct rtl8xxxu_priv *priv, const char *fw_name);
void rtl8xxxu_firmware_self_reset(struct rtl8xxxu_priv *priv);
-void rtl8xxxu_power_off(struct rtl8xxxu_priv *priv);
void rtl8xxxu_identify_vendor_1bit(struct rtl8xxxu_priv *priv, u32 vendor);
void rtl8xxxu_identify_vendor_2bits(struct rtl8xxxu_priv *priv, u32 vendor);
void rtl8xxxu_config_endpoints_sie(struct rtl8xxxu_priv *priv);
projects / thirdparty / linux.git / commitdiff
