--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+
+#include "mt7981b.dtsi"
+
+/ {
+ model = "Cudy AP3000 Wall v1";
+ compatible = "cudy,ap3000wall-v1", "mediatek,mt7981";
+
+ aliases {
+ label-mac-device = &gmac0;
+ led-boot = &led_status_white;
+ led-failsafe = &led_status_red;
+ led-running = &led_status_white;
+ led-upgrade = &led_status_red;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ lights_toggle {
+ label = "lights_toggle";
+ linux,code = <KEY_LIGHTS_TOGGLE>;
+ gpios = <&pio 35 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led_status_red: led@0 {
+ label = "red:status";
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&pio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_white: led@1 {
+ label = "white:status";
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ };
+
+ };
+
+ gpio_export {
+ compatible = "gpio-export";
+
+ poe_passthrough {
+ gpio-export,name = "poe-passthrough";
+ gpio-export,output = <0>;
+ gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ watchdog-hw {
+ compatible = "linux,wdt-gpio";
+ gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
+ hw_algo = "level";
+ hw_margin_ms = <10000>;
+ always-running;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+ð {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+ status = "okay";
+
+ gmac0: mac@0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_bdinfo_de00 0>;
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+};
+
+&mdio_bus {
+ switch: switch@1f {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_flash_pins>;
+ status = "okay";
+
+ spi_nand: flash@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <52000000>;
+
+ spi-cal-enable;
+ spi-cal-mode = "read-data";
+ spi-cal-datalen = <7>;
+ spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
+ spi-cal-addrlen = <5>;
+ spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ mediatek,nmbm;
+ mediatek,bmt-max-ratio = <1>;
+ mediatek,bmt-max-reserved-blocks = <64>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "BL2";
+ reg = <0x00000 0x0100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "u-boot-env";
+ reg = <0x0100000 0x0080000>;
+ read-only;
+ };
+
+ factory: partition@180000 {
+ label = "Factory";
+ reg = <0x180000 0x0200000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom@0 {
+ reg = <0x0 0x1000>;
+ };
+ };
+ };
+
+ partition@380000 {
+ label = "bdinfo";
+ reg = <0x380000 0x0040000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_bdinfo_de00: macaddr@de00 {
+ compatible = "mac-base";
+ reg = <0xde00 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition@3c0000 {
+ label = "FIP";
+ reg = <0x3c0000 0x0200000>;
+ read-only;
+ };
+
+ partition@5c0000 {
+ label = "ubi";
+ reg = <0x5c0000 0x4000000>;
+ compatible = "linux,ubi";
+ };
+ };
+ };
+};
+
+&pio {
+ spi0_flash_pins: spi0-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+ };
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan5";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&wifi {
+ status = "okay";
+ nvmem-cells = <&eeprom_factory_0>;
+ nvmem-cell-names = "eeprom";
+};
projects / thirdparty / openwrt.git / commitdiff
