mediatek: add support for Cudy WR3000U v1

Hardware:
 - SoC: MediaTek MT7981B
 - CPU: 2x 1.3 GHz Cortex-A53
 - Flash: 256 MiB ESMT F50L2G41XA
 - RAM: DDR3, 512 MiB
 - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
 - 1x WAN MT7531 (JXD 2531Z) 10/100/1000 Mbps
 - 4x LAN 2x MT7530 (JXD 2529S) 10/100/1000 Mbps
 - USB 3.0 port
 - Buttons: Reset, WPS
 - 8x LEDs: 2x Red, 6x Blue
 - Serial console: no need to solder. 115200 8n1
 - Power: 12 VDC, 1.5 A

The DTS inherits WBR3000UAX because WR3000U is almost the same.
The only difference is size of NAND and factory UBI length.

+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | D4:0D:AB:xx:xx:x1 | label+1   |
| LAN     | D4:0D:AB:xx:xx:x0 | label     |
| WLAN 2g | D4:0D:AB:xx:xx:x0 | label     |
| WLAN 5g | D6:0D:AB:xx:xx:x1 | label+1   |
+---------+-------------------+-----------+

There are 2 ways to install OpenWrt:
- via an intermediate RSA-signed vendor's image or
- via UART && TFTPd

Migration to OpenWrt via OEM firmware:
- Download the migration image from
  https://drive.google.com/drive/folders/1BKVarlwlNxf7uJUtRhuMGUqeCa5KpMnj
  (The folder is Cudy's official "Cudy Intermediary OpenWrt Firmware" resource)
- Upload the migration image via OEM web interface
- After flashing, OpenWrt is accessible via http://192.168.1.1
- Flash the official OpenWrt image

Install using UART & TFTP:
- Connect to UART.
- Connect to LAN and set your IP to 192.168.1.88/24.
- Configure a TFTP server to serve
  openwrt-mediatek-filogic-cudy_wr3000u-v1-initramfs-kernel.bin file
  and run the TFTP server.
- Press reset and power-on the router. Hold the reset button for 5 seconds
- TFTP error: 'File not found' appears and MTK console becomes available
- Enter the following commands in the console:
  setenv bootfile openwrt-mediatek-filogic-cudy_wr3000u-v1-initramfs-kernel.bin
  tftpboot
  bootm
- After booting to initramfs, via http://192.168.1.1 flash
  openwrt-mediatek-filogic-cudy_wr3000u-v1-squashfs-sysupgrade.bin
- After flashing, OpenWrt is accessible via http://192.168.1.1

If you fail to flash the device,
you can use TFTP to flash back to the original firmware:
- Download the original firmware from
  https://www.cudy.com/pages/download-center/wr3000u-256mb-1-0
- Connect to LAN and set your IP to 192.168.1.88/24.
  Configure a TFTP server and an recovery.bin firmware file
- With the router off, press the RESET button.
  While the router is turning on,
  the button should continue to be pressed for at least 5 seconds
- After 1-2 minutes the original firmware is available on http://192.168.10.1

Signed-off-by: Dmitry Mostovoy <stavultras@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/24447
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

diff --git a/target/linux/mediatek/dts/mt7981b-cudy-wr3000u-v1.dts b/target/linux/mediatek/dts/mt7981b-cudy-wr3000u-v1.dts
new file mode 100644 (file)
index 0000000..58b39b2
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-cudy-wr3000u-v1.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+#include "mt7981b-cudy-wbr3000uax-v1.dtsi"
+
+/ {
+       model = "Cudy WR3000U v1";
+       compatible = "cudy,wr3000u-v1", "mediatek,mt7981";
+};
+
+&spi_nand {
+       mediatek,nmbm;
+       mediatek,bmt-max-ratio = <1>;
+       mediatek,bmt-max-reserved-blocks = <64>;
+};
+
+&ubi {
+       reg = <0x5c0000 0xe600000>;
+};

diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
index f99303bc3d7c7607f8418e66bf10d3be9584d48e..d2c718b50dc4eae5378128890be309a9395977ff 100644 (file)
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -97,6 +97,7 @@ cudy,wr3000p-v1-ubootmod)
        ucidef_set_led_netdev "wan" "wan" "white:wan" "wan" "link tx rx"
        ucidef_set_led_netdev "internet" "internet" "white:wan-online" "wan" "link"
        ;;
+cudy,wr3000u-v1|\
 cudy,wbr3000uax-v1|\
 cudy,wbr3000uax-v1-ubootmod)
        ucidef_set_led_default "internet_off" "internet_off" "red:fault" "1"

diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index f598cb549dad8ce7bc799b2af4066abb3dead646..d3b84ce6edcf9c32040a4bc69b342e4b54a3fe0e 100644 (file)
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -99,6 +99,7 @@ case "$board" in
        cudy,tr3000-256mb-v1|\
        cudy,tr3000-v1|\
        cudy,tr3000-v1-ubootmod|\
+       cudy,wr3000u-v1|\
        cudy,wbr3000uax-v1|\
        cudy,wbr3000uax-v1-ubootmod|\
        cudy,wr3000e-v1|\

diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index aebd0d5c4776f2889ad31237dcec9a0916c89a61..9ca544c599fca344eb01804761fd2d60a9a48c20 100644 (file)
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -1558,6 +1558,23 @@ define Device/cudy_wr3000p-v1-ubootmod
 endef
 TARGET_DEVICES += cudy_wr3000p-v1-ubootmod
 
+define Device/cudy_wr3000u-v1
+  DEVICE_VENDOR := Cudy
+  DEVICE_MODEL := WR3000U
+  DEVICE_VARIANT := v1
+  DEVICE_DTS := mt7981b-cudy-wr3000u-v1
+  DEVICE_DTS_DIR := ../dts
+  SUPPORTED_DEVICES += R138
+  UBINIZE_OPTS := -E 5
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  IMAGE_SIZE := 235520k
+  KERNEL_IN_UBI := 1
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+  DEVICE_PACKAGES := kmod-usb3 kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
+endef
+TARGET_DEVICES += cudy_wr3000u-v1
+
 define Device/cudy_wbr3000uax-v1
   DEVICE_VENDOR := Cudy
   DEVICE_MODEL := WBR3000UAX