]> git.ipfire.org Git - thirdparty/openwrt.git/commitdiff
mediatek: add support for Zbtlink ZBT-Z8102AX v2 18514/head
authorMarius Durbaca <mariusd84@gmail.com>
Tue, 22 Oct 2024 13:15:57 +0000 (16:15 +0300)
committerHauke Mehrtens <hauke@hauke-m.de>
Mon, 16 Jun 2025 20:46:55 +0000 (22:46 +0200)
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

Installation:
1. Power down the router and hold in the Reset button.
2. While holding in the button power up the router again.
3. Hold the button in for 10 seconds and then release.
4. Use your browser to go to 192.168.1.1
5. If you see a GUI that is for flashing firmware then you have the V2 model.
If there is no GUI and the router continues to boot up normally
you have the V1 model.
6. Now use the V2 sysugrade file.

Note: Recovery GUI it can be used to recover from an incorrect firmware flash.

Based on patches adding support for this device by Yannick Chabanois (openmptcprouter)
and Dairyman (ofmodemsandmen)

Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18514
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8102ax-v2.dts [new file with mode: 0644]
target/linux/mediatek/filogic/base-files/etc/board.d/02_network
target/linux/mediatek/filogic/base-files/etc/board.d/03_gpio_switches
target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
target/linux/mediatek/image/filogic.mk

diff --git a/target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8102ax-v2.dts b/target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8102ax-v2.dts
new file mode 100644 (file)
index 0000000..6557b0f
--- /dev/null
@@ -0,0 +1,337 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT 
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "mt7981b.dtsi"
+
+/ {
+       model = "ZBT Z8102AX V2";
+       compatible = "zbtlink,zbt-z8102ax-v2", "mediatek,mt7981";
+
+       aliases {
+               serial0 = &uart0;
+               led-boot = &led_status_red;
+               led-failsafe = &led_status_red;
+               led-running = &led_status_green;
+               led-upgrade = &led_status_green;
+               label-mac-device = &gmac0;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+               bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8";
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+               };
+
+               wps {
+                       label = "wps";
+                       linux,code = <KEY_WPS_BUTTON>;
+                       gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+               };
+               
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_status_red: red {
+                       gpios = <&pio 9 GPIO_ACTIVE_HIGH>;
+                       color = <LED_COLOR_ID_RED>;
+                       function = LED_FUNCTION_STATUS;
+               };
+
+               led_status_green: green {
+                       gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_GREEN>;
+                       function = LED_FUNCTION_STATUS;
+               };
+               
+               led_status_blue: blue {
+                       gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_BLUE>;
+                       function = LED_FUNCTION_STATUS;
+               };
+               
+               led_status_5g1: 5g1 {
+                       gpios = <&pio 8 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_BLUE>;
+                       function = LED_FUNCTION_USB;
+                       function-enumerator = <0>;
+               };
+               
+               led_status_5g2: 5g2 {
+                       gpios = <&pio 13 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_BLUE>;
+                       function = LED_FUNCTION_USB;
+                       function-enumerator = <1>;
+               };
+       };
+
+       watchdog {
+               compatible = "linux,wdt-gpio";
+               gpios = <&pio 2 GPIO_ACTIVE_HIGH>;
+               hw_algo = "toggle";
+               hw_margin_ms = <1000>;
+       };
+
+       gpio-export {
+               compatible = "gpio-export";
+               #size-cells = <0>;
+
+               pcie {
+                       gpio-export,name = "pcie_power";
+                       gpio-export,output = <1>;
+                       gpios = <&pio 3 GPIO_ACTIVE_HIGH>;
+               };
+
+               5g1 {
+                       gpio-export,name = "5g1";
+                       gpio-export,output = <1>;
+                       gpios = <&pio 4 GPIO_ACTIVE_HIGH>;
+               };
+
+               5g2 {
+                       gpio-export,name = "5g2";
+                       gpio-export,output = <1>;
+                       gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+               };
+
+               sim1 {
+                       gpio-export,name = "sim1";
+                       gpio-export,output = <0>;
+                       gpios = <&pio 6 GPIO_ACTIVE_LOW>;
+               };
+
+               sim2 {
+                       gpio-export,name = "sim2";
+                       gpio-export,output = <0>;
+                       gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+               };
+       };
+};
+
+&eth {
+       status = "okay";
+
+       gmac0: mac@0 {
+               compatible = "mediatek,eth-mac";
+               reg = <0>;
+               phy-mode = "2500base-x";
+               nvmem-cell-names = "mac-address";
+
+               fixed-link {
+                       speed = <2500>;
+                       full-duplex;
+                       pause;
+               };
+       };
+       
+       gmac1: mac@1 {
+               compatible = "mediatek,eth-mac";
+               reg = <1>;
+               phy-mode = "gmii";
+               phy-handle = <&int_gbe_phy>;
+               nvmem-cell-names = "mac-address";
+               nvmem-cells = <&macaddr_factory_02a>;
+       };
+};
+
+&mdio_bus {
+       switch: switch@1f {
+               compatible = "mediatek,mt7531";
+               reg = <31>;
+               reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+               interrupt-controller;
+               #interrupt-cells = <1>;
+               interrupt-parent = <&pio>;
+               interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+       };
+};
+
+&spi0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&spi0_flash_pins>;
+       status = "okay";
+
+       spi_nand@0 {
+               compatible = "spi-nand";
+               #address-cells = <1>;
+               #size-cells = <1>;
+               reg = <0>;
+
+               spi-max-frequency = <52000000>;
+               spi-tx-buswidth = <4>;
+               spi-rx-buswidth = <4>;
+
+               mediatek,nmbm;
+               mediatek,bmt-max-ratio = <1>;
+               mediatek,bmt-max-reserved-blocks = <64>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "bl2";
+                               reg = <0x0000000 0x0100000>;
+                               read-only;
+                       };
+
+                       partition@100000 {
+                               label = "u-boot-env";
+                               reg = <0x0100000 0x0080000>;
+                       };
+
+                       factory: partition@180000 {
+                               label = "Factory";
+                               reg = <0x0180000 0x0200000>;
+                               read-only;
+                       };
+
+                       partition@380000 {
+                               label = "FIP";
+                               reg = <0x0380000 0x0200000>;
+                               read-only;
+                       };
+
+                       nand_rootfs: partition@580000 {
+                               label = "ubi";
+                               reg = <0x0580000 0x7220000>;
+                       };
+               };
+       };
+};
+
+&switch {
+       ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               port@0 {
+                       reg = <0>;
+                       label = "lan1";
+                       nvmem-cell-names = "mac-address";
+                       nvmem-cells = <&macaddr_factory_004>;
+               };
+
+               port@1 {
+                       reg = <1>;
+                       label = "lan2";
+                       nvmem-cell-names = "mac-address";
+                       nvmem-cells = <&macaddr_factory_004>;
+               };
+
+               port@2 {
+                       reg = <2>;
+                       label = "lan3";
+                       nvmem-cell-names = "mac-address";
+                       nvmem-cells = <&macaddr_factory_004>;
+               };
+
+               port@3 {
+                       reg = <3>;
+                       label = "lan4";
+                       nvmem-cell-names = "mac-address";
+                       nvmem-cells = <&macaddr_factory_004>;
+               };
+
+               port@6 {
+                       reg = <6>;
+                       label = "cpu";
+                       ethernet = <&gmac0>;
+                       phy-mode = "2500base-x";
+
+                       fixed-link {
+                               speed = <2500>;
+                               full-duplex;
+                               pause;
+                       };
+               };
+       };
+};
+
+&pio {
+       gpio-line-names = 
+                       "wps",
+                       "reset",
+                       "watchdog",
+                       "pcie",
+                       "5g1",
+                       "5g2",
+                       "sim1",
+                       "sim2",
+                       "5g1_status",
+                       "red_status",
+                       "green_status",
+                       "blue_status",
+                       "",
+                       "5g2_status";
+
+       spi0_flash_pins: spi0-pins {
+               mux {
+                       function = "spi";
+                       groups = "spi0", "spi0_wp_hold";
+               };
+
+               conf-pu {
+                       pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+                       drive-strength = <8>;
+                       mediatek,pull-up-adv = <0>; /* bias-disable */
+               };
+
+               conf-pd {
+                       pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+                       drive-strength = <8>;
+                       mediatek,pull-up-adv = <0>; /* bias-disable */
+               };
+       };
+};
+
+&uart0 {
+       status = "okay";
+};
+
+&watchdog {
+       status = "okay";
+};
+
+&usb_phy {
+       status = "okay";
+};
+
+&xhci {
+       status = "okay";
+};
+
+&wifi {
+       status = "okay";
+        nvmem-cells = <&eeprom_factory>;
+        nvmem-cell-names = "eeprom";
+};
+
+&factory {
+       compatible = "nvmem-cells";
+       #address-cells = <1>;
+       #size-cells = <1>;
+
+       macaddr_factory_004: macaddr@004 {
+               reg = <0x004 0x6>;
+       };
+       macaddr_factory_02a: macaddr@02a {
+               reg = <0x02a 0x6>;
+       };
+        eeprom_factory: eeprom@0 {
+               reg = <0x0 0x1000>;
+       };
+};
index 861928d82da6c425ae3af0f53cc317fa387787b4..a96ea99bc902b87c4ab0c620094e9c35349e9787 100644 (file)
@@ -57,6 +57,7 @@ mediatek_setup_interfaces()
        ruijie,rg-x60-pro|\
        unielec,u7981-01*|\
        zbtlink,zbt-z8102ax|\
+       zbtlink,zbt-z8102ax-v2|\
        zyxel,ex5601-t0-stock|\
        zyxel,ex5601-t0-ubootmod)
                ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" eth1
index 4cbec1ef078db310b3afaf03e428c755a264e65c..1fe74f2b6fd4566788d0cbd74ec0c590a410efe0 100644 (file)
@@ -5,7 +5,8 @@ board_config_update
 board=$(board_name)
 
 case "$board" in
-zbtlink,zbt-z8102ax)
+zbtlink,zbt-z8102ax|\
+zbtlink,zbt-z8102ax-v2)
        ucidef_add_gpio_switch "5g1" "Power 1st modem" "5g1" "1"
        ucidef_add_gpio_switch "5g2" "Power 2nd modem" "5g2" "1"
        ucidef_add_gpio_switch "pcie" "Power PCIe port" "pcie" "1"
index 5ca1ca462f5588f55090dab3e45fc28b834bab92..c42399cf6454c8cd59db9bc78644c657442de992 100644 (file)
@@ -185,6 +185,7 @@ case "$board" in
        routerich,ax3000|\
        routerich,ax3000-ubootmod|\
        zbtlink,zbt-z8102ax|\
+       zbtlink,zbt-z8102ax-v2|\
        zbtlink,zbt-z8103ax|\
        zyxel,ex5601-t0-stock|\
        zyxel,ex5601-t0-ubootmod)
index 337403411a1a79385cd57ca9e8ae92dbcb6b87c0..b977d6117e0b08c9836ff8b0943ab7d755932ac1 100644 (file)
@@ -2015,6 +2015,23 @@ define Device/zbtlink_zbt-z8102ax
 endef
 TARGET_DEVICES += zbtlink_zbt-z8102ax
 
+define Device/zbtlink_zbt-z8102ax-v2
+  DEVICE_VENDOR := Zbtlink
+  DEVICE_MODEL := ZBT-Z8102AX-V2
+  DEVICE_DTS := mt7981b-zbtlink-zbt-z8102ax-v2
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3 kmod-usb-net-qmi-wwan kmod-usb-serial-option
+  KERNEL_IN_UBI := 1
+  UBINIZE_OPTS := -E 5
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  IMAGE_SIZE := 65536k
+  IMAGES += factory.bin
+  IMAGE/factory.bin := append-ubi | check-size $$(IMAGE_SIZE)
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += zbtlink_zbt-z8102ax-v2
+
 define Device/zbtlink_zbt-z8103ax
   DEVICE_VENDOR := Zbtlink
   DEVICE_MODEL := ZBT-Z8103AX