#define CST4313_SPROM_OTP_SEL_SHIFT 0
/* 4313 Chip specific ChipControl register bits */
- /* 12 mA drive strengh for later 4313 */
+ /* 12 mA drive strength for later 4313 */
#define CCTRL_4313_12MA_LED_DRIVE 0x00000007
/* Manufacturer Ids */
/* get chipcommon chipstatus */
sii->chipst = bcma_read32(cc, CHIPCREGOFFS(chipstatus));
- /* get chipcommon capabilites */
+ /* get chipcommon capabilities */
sii->pub.cccaps = bcma_read32(cc, CHIPCREGOFFS(capabilities));
/* get pmu rev and caps */
}
/*
- * clock control policy function throught chipcommon
+ * clock control policy function through chipcommon
*
* set dynamic clk control mode (forceslow, forcefast, dynamic)
* returns true if we are forcing fast clock
* conventions for the use the flash space:
*/
-/* Minumum amount of flash we support */
+/* Minimum amount of flash we support */
#define FLASH_MIN 0x00020000 /* Minimum flash size */
#define CC_SROM_OTP 0x800 /* SROM/OTP address space */
/*
* Preps the given packet for AMPDU based on the session data. If the
- * frame cannot be accomodated in the current session, -ENOSPC is
+ * frame cannot be accommodated in the current session, -ENOSPC is
* returned.
*/
int brcms_c_ampdu_add_frame(struct brcms_ampdu_session *session,
}
/*
- * Now that we're sure this frame can be accomodated, update the
+ * Now that we're sure this frame can be accommodated, update the
* session information.
*/
session->ampdu_len += len;
/*
* OFDM 40 MHz SISO has the same power as the corresponding
- * MCS0-7 rate unless overriden by the locale specific code.
+ * MCS0-7 rate unless overridden by the locale specific code.
* We set this value to 0 as a flag (presumably 0 dBm isn't
* a possibility) and then copy the MCS0-7 value to the 40 MHz
* value if it wasn't explicitly set.
/*
* 20 MHz has the same power as the corresponding OFDM rate
- * unless overriden by the locale specific code.
+ * unless overridden by the locale specific code.
*/
txpwr->mcs_20_siso[i] = txpwr->ofdm[i];
txpwr->mcs_40_siso[i] = 0;
ret = brcms_c_ampdu_add_frame(session, p);
if (ret == -ENOSPC) {
/*
- * AMPDU cannot accomodate this frame. Close out the in-
+ * AMPDU cannot accommodate this frame. Close out the in-
* progress AMPDU session and start a new one.
*/
ampdu_finalize(di);
FIF_BCN_PRBRESP_PROMISC | \
FIF_PSPOLL)
-#define CHAN2GHZ(channel, freqency, chflags) { \
+#define CHAN2GHZ(channel, frequency, chflags) { \
.band = NL80211_BAND_2GHZ, \
- .center_freq = (freqency), \
+ .center_freq = (frequency), \
.hw_value = (channel), \
.flags = chflags, \
.max_antenna_gain = 0, \
* The "fallback limit" is the number of tx attempts a given
* MPDU is sent at the "primary" rate. Tx attempts beyond that
* limit are sent at the "secondary" rate.
- * A 'short frame' does not exceed RTS treshold.
+ * A 'short frame' does not exceed RTS threshold.
*/
u16 sfbl, /* Short Frame Rate Fallback Limit */
lfbl, /* Long Frame Rate Fallback Limit */
}
/*
- * Currently only support same setting for primay and
+ * Currently only support same setting for primary and
* fallback rates. Unify flags for each rate into a
* single value for the frame
*/
* cur_etheraddr: h/w address
* flags: BSSCFG flags; see below
*
- * current_bss: BSS parms in ASSOCIATED state
+ * current_bss: BSS parameters in ASSOCIATED state
*
*
* ID: 'unique' ID of this bsscfg, assigned at bsscfg allocation
#define EXT_ILP_HZ 32768
/*
- * Duration for ILP clock frequency measurment in milliseconds
+ * Duration for ILP clock frequency measurement in milliseconds
*
* remark: 1000 must be an integer multiple of this duration
*/
projects / thirdparty / kernel / stable.git / commitdiff
