rockchip: add HINLINK H28K support

Hardware:
- RK3528 SoC
- 1x USB 2.0
- 8/32GB eMMC
- 1/2/4GB LPDDR4
- 1x 1GbE RTL8111H
- 1x 1GbE RTL8211F
- MicroSD card slot

Installation:
  Use dd or balenaEtcher to flash the firmware.

Note:
  The RK3528 SoC does not support MSI-X, so it can't
  adjust the interrupts of r8169 to other CPU cores.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>

diff --git a/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds b/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds
index b37eaef9c9b16ef03c5ac2b4e10ae13ab59c0a7b..f098f55e2c71d239b5799f5d166022e9ba9c6281 100644 (file)
--- a/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds
+++ b/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds
@@ -39,6 +39,10 @@ friendlyarm,nanopi-r76s)
        ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1"
        ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0"
        ;;
+hinlink,h28k)
+       ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1"
+       ucidef_set_led_netdev "lan" "LAN" "amber:lan" "eth0"
+       ;;
 radxa,e20c)
        ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0"
        ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1"

diff --git a/target/linux/rockchip/armv8/base-files/etc/board.d/02_network b/target/linux/rockchip/armv8/base-files/etc/board.d/02_network
index f5796bb8b1a6437815edfe660eeb62efa3ab4bd7..ea4a2cc945c1a490373f2e77532a138bac3b86e9 100644 (file)
--- a/target/linux/rockchip/armv8/base-files/etc/board.d/02_network
+++ b/target/linux/rockchip/armv8/base-files/etc/board.d/02_network
@@ -23,6 +23,7 @@ rockchip_setup_interfaces()
        friendlyarm,nanopc-t6|\
        friendlyarm,nanopi-r5c|\
        friendlyarm,nanopi-r76s|\
+       hinlink,h28k|\
        lunzn,fastrhino-r66s|\
        radxa,e20c|\
        radxa,e25|\
@@ -77,6 +78,7 @@ rockchip_setup_macs()
        friendlyarm,nanopi-r2c|\
        friendlyarm,nanopi-r2s|\
        friendlyarm,nanopi-r76s|\
+       hinlink,h28k|\
        linkease,easepi-r1|\
        lunzn,fastrhino-r66s)
                wan_mac=$(macaddr_generate_from_mmc_cid mmcblk0)

diff --git a/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity b/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity
index e758605ca73488529b339aea77cf68526ab78534..d273f53a4b4f1a7d3e589a1b6ce20376485958f6 100644 (file)
--- a/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity
+++ b/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity
@@ -34,7 +34,6 @@ friendlyarm,nanopi-r3s|\
 friendlyarm,nanopi-r5c|\
 linkease,easepi-r1|\
 lunzn,fastrhino-r66s|\
-radxa,e20c|\
 radxa,e25|\
 sinovoip,rk3568-bpi-r2pro)
        set_interface_core 2 "eth0"
@@ -69,6 +68,10 @@ friendlyarm,nanopi-r6s)
        set_interface_core 20 "eth1"
        set_interface_core 40 "eth2"
        ;;
+hinlink,h28k|\
+radxa,e20c)
+       set_interface_core 2 "eth0"
+       ;;
 radxa,rock-5a|\
 radxa,rock-5c)
        set_interface_core 10 "eth1"

diff --git a/target/linux/rockchip/image/armv8.mk b/target/linux/rockchip/image/armv8.mk
index 29ec6de66452091d719c91201bbf8accc8e6bef0..b9f1fcab0ec6b972632ac8121cfc2c84b5087bd4 100644 (file)
--- a/target/linux/rockchip/image/armv8.mk
+++ b/target/linux/rockchip/image/armv8.mk
@@ -180,6 +180,18 @@ define Device/friendlyarm_nanopi-r76s
 endef
 TARGET_DEVICES += friendlyarm_nanopi-r76s
 
+define Device/hinlink_h28k
+  $(Device/rk3528)
+  DEVICE_VENDOR := HINLINK
+  DEVICE_MODEL := H28K
+  DEVICE_ALT0_VENDOR := LinkStar
+  DEVICE_ALT0_MODEL := H28K
+  DEVICE_DTS := rk3528-hinlink-h28k
+  UBOOT_DEVICE_NAME := hinlink-h28k-rk3528
+  DEVICE_PACKAGES := kmod-r8169
+endef
+TARGET_DEVICES += hinlink_h28k
+
 define Device/linkease_easepi-r1
   $(Device/rk3568)
   DEVICE_VENDOR := LinkEase

diff --git a/target/linux/rockchip/patches-6.12/101-arm64-dts-rockchip-Add-HINLINK-H28K.patch b/target/linux/rockchip/patches-6.12/101-arm64-dts-rockchip-Add-HINLINK-H28K.patch
new file mode 100644 (file)
index 0000000..ea6be6f
--- /dev/null
+++ b/target/linux/rockchip/patches-6.12/101-arm64-dts-rockchip-Add-HINLINK-H28K.patch
@@ -0,0 +1,353 @@
+From dca5896703826d0d5fadcc11ee755b83db705571 Mon Sep 17 00:00:00 2001
+From: Chukun Pan <amadeus@jmu.edu.cn>
+Date: Mon,  1 Dec 2025 18:00:06 +0800
+Subject: [PATCH] arm64: dts: rockchip: Add HINLINK H28K
+
+The HINLINK H28K is a development board with the
+Rockchip RK3528 SoC. It has the following features:
+
+- 1x USB 2.0
+- 8/32GB eMMC
+- 1/2/4GB LPDDR4
+- MicroSD card slot
+- 1x 1GbE RTL8111H Ethernet
+- 1x 1GbE RTL8211F Ethernet
+
+Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
+---
+ arch/arm64/boot/dts/rockchip/Makefile         |   1 +
+ .../boot/dts/rockchip/rk3528-hinlink-h28k.dts | 301 ++++++++++++++++++
+ 2 files changed, 302 insertions(+)
+ create mode 100644 arch/arm64/boot/dts/rockchip/rk3528-hinlink-h28k.dts
+
+--- a/arch/arm64/boot/dts/rockchip/Makefile
++++ b/arch/arm64/boot/dts/rockchip/Makefile
+@@ -76,6 +76,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-ro
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire.dtb
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399pro-rock-pi-n10.dtb
++dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3528-hinlink-h28k.dtb
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3528-radxa-e20c.dtb
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3528-rock-2a.dtb
+ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3528-rock-2f.dtb
+--- /dev/null
++++ b/arch/arm64/boot/dts/rockchip/rk3528-hinlink-h28k.dts
+@@ -0,0 +1,318 @@
++// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
++
++/dts-v1/;
++
++#include <dt-bindings/input/input.h>
++#include <dt-bindings/leds/common.h>
++#include <dt-bindings/pwm/pwm.h>
++#include "rk3528.dtsi"
++
++/ {
++      model = "HINLINK H28K";
++      compatible = "hinlink,h28k", "rockchip,rk3528";
++
++      aliases {
++              ethernet0 = &gmac1;
++              mmc0 = &sdhci;
++              mmc1 = &sdmmc;
++              serial0 = &uart0;
++      };
++
++      chosen {
++              stdout-path = "serial0:1500000n8";
++      };
++
++      keys {
++              compatible = "adc-keys";
++              io-channels = <&saradc 0>;
++              io-channel-names = "buttons";
++              keyup-threshold-microvolt = <1800000>;
++              poll-interval = <100>;
++
++              button-boot {
++                      label = "BOOT";
++                      linux,code = <KEY_SETUP>;
++                      press-threshold-microvolt = <0>;
++              };
++      };
++
++      leds {
++              compatible = "gpio-leds";
++              pinctrl-names = "default";
++              pinctrl-0 = <&lan_led>, <&wan_led>, <&work_led>;
++
++              led-0 {
++                      color = <LED_COLOR_ID_AMBER>;
++                      function = LED_FUNCTION_LAN;
++                      gpios = <&gpio4 RK_PC1 GPIO_ACTIVE_LOW>;
++                      linux,default-trigger = "netdev";
++              };
++
++              led-1 {
++                      color = <LED_COLOR_ID_BLUE>;
++                      function = LED_FUNCTION_WAN;
++                      gpios = <&gpio4 RK_PC0 GPIO_ACTIVE_LOW>;
++                      linux,default-trigger = "netdev";
++              };
++
++              led-2 {
++                      color = <LED_COLOR_ID_GREEN>;
++                      function = LED_FUNCTION_STATUS;
++                      gpios = <&gpio4 RK_PB7 GPIO_ACTIVE_LOW>;
++                      linux,default-trigger = "default-on";
++              };
++      };
++
++      vdd_0v9: regulator-0v9-vdd {
++              compatible = "regulator-fixed";
++              regulator-name = "vdd_0v9";
++              regulator-always-on;
++              regulator-boot-on;
++              regulator-min-microvolt = <900000>;
++              regulator-max-microvolt = <900000>;
++              vin-supply = <&vcc5v0_sys>;
++      };
++
++      vcc_ddr: regulator-1v1-vcc-ddr {
++              compatible = "regulator-fixed";
++              regulator-name = "vcc_ddr";
++              regulator-always-on;
++              regulator-boot-on;
++              regulator-min-microvolt = <1100000>;
++              regulator-max-microvolt = <1100000>;
++              vin-supply = <&vcc5v0_sys>;
++      };
++
++      vcc_1v8: regulator-1v8-vcc {
++              compatible = "regulator-fixed";
++              regulator-name = "vcc_1v8";
++              regulator-always-on;
++              regulator-boot-on;
++              regulator-min-microvolt = <1800000>;
++              regulator-max-microvolt = <1800000>;
++              vin-supply = <&vcc_3v3>;
++      };
++
++      vcc_3v3: regulator-3v3-vcc {
++              compatible = "regulator-fixed";
++              regulator-name = "vcc_3v3";
++              regulator-always-on;
++              regulator-boot-on;
++              regulator-min-microvolt = <3300000>;
++              regulator-max-microvolt = <3300000>;
++              vin-supply = <&vcc5v0_sys>;
++      };
++
++      vcc3v3_sd: regulator-3v3-vcc-sd {
++              compatible = "regulator-fixed";
++              gpios = <&gpio4 RK_PA1 GPIO_ACTIVE_LOW>;
++              pinctrl-names = "default";
++              pinctrl-0 = <&sdmmc_pwren_l>;
++              regulator-name = "vcc3v3_sd";
++              regulator-min-microvolt = <3300000>;
++              regulator-max-microvolt = <3300000>;
++              vin-supply = <&vcc_3v3>;
++      };
++
++      vcc5v0_sys: regulator-5v0-vcc-sys {
++              compatible = "regulator-fixed";
++              regulator-name = "vcc5v0_sys";
++              regulator-always-on;
++              regulator-boot-on;
++              regulator-min-microvolt = <5000000>;
++              regulator-max-microvolt = <5000000>;
++      };
++
++      vccio_sd: regulator-vccio-sd {
++              compatible = "regulator-gpio";
++              gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
++              pinctrl-names = "default";
++              pinctrl-0 = <&sdmmc_vol_ctrl_h>;
++              regulator-name = "vccio_sd";
++              regulator-min-microvolt = <1800000>;
++              regulator-max-microvolt = <3300000>;
++              states = <1800000 0x0>, <3300000 0x1>;
++              vin-supply = <&vcc5v0_sys>;
++      };
++
++      vdd_arm: regulator-vdd-arm {
++              compatible = "pwm-regulator";
++              pwms = <&pwm1 0 5000 PWM_POLARITY_INVERTED>;
++              pwm-supply = <&vcc5v0_sys>;
++              regulator-name = "vdd_arm";
++              regulator-always-on;
++              regulator-boot-on;
++              regulator-min-microvolt = <746000>;
++              regulator-max-microvolt = <1201000>;
++              regulator-settling-time-up-us = <250>;
++      };
++
++      vdd_logic: regulator-vdd-logic {
++              compatible = "pwm-regulator";
++              pwms = <&pwm2 0 5000 PWM_POLARITY_INVERTED>;
++              pwm-supply = <&vcc5v0_sys>;
++              regulator-name = "vdd_logic";
++              regulator-always-on;
++              regulator-boot-on;
++              regulator-min-microvolt = <705000>;
++              regulator-max-microvolt = <1006000>;
++              regulator-settling-time-up-us = <250>;
++      };
++};
++
++&combphy {
++      status = "okay";
++};
++
++&cpu0 {
++      cpu-supply = <&vdd_arm>;
++};
++
++&cpu1 {
++      cpu-supply = <&vdd_arm>;
++};
++
++&cpu2 {
++      cpu-supply = <&vdd_arm>;
++};
++
++&cpu3 {
++      cpu-supply = <&vdd_arm>;
++};
++
++&gmac1 {
++      clock_in_out = "output";
++      phy-handle = <&rgmii_phy>;
++      phy-mode = "rgmii-id";
++      phy-supply = <&vcc_3v3>;
++      pinctrl-names = "default";
++      pinctrl-0 = <&rgmii_miim>,
++                  <&rgmii_tx_bus2>,
++                  <&rgmii_rx_bus2>,
++                  <&rgmii_rgmii_clk>,
++                  <&rgmii_rgmii_bus>;
++      status = "okay";
++};
++
++&gpu {
++      mali-supply = <&vdd_logic>;
++      status = "okay";
++};
++
++&mdio1 {
++      rgmii_phy: ethernet-phy@1 {
++              compatible = "ethernet-phy-ieee802.3-c22";
++              reg = <0x1>;
++              pinctrl-names = "default";
++              pinctrl-0 = <&gmac1_rstn_l>;
++              reset-assert-us = <20000>;
++              reset-deassert-us = <100000>;
++              reset-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_LOW>;
++      };
++};
++
++&pcie {
++      pinctrl-names = "default";
++      pinctrl-0 = <&rtl8111hs_isolateb_l>;
++      reset-gpios = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>;
++      vpcie3v3-supply = <&vcc_3v3>;
++      status = "okay";
++};
++
++&pinctrl {
++      gmac {
++              gmac1_rstn_l: gmac1-rstn-l {
++                      rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
++              };
++      };
++
++      leds {
++              lan_led: lan-led {
++                      rockchip,pins = <4 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
++              };
++
++              wan_led: wan-led {
++                      rockchip,pins = <4 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
++              };
++
++              work_led: work-led {
++                      rockchip,pins = <4 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
++              };
++      };
++
++      pcie {
++              rtl8111hs_isolateb_l: rtl8111hs-isolateb-l {
++                      rockchip,pins = <4 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
++              };
++      };
++
++      sdmmc {
++              sdmmc_pwren_l: sdmmc-pwren-l {
++                      rockchip,pins = <4 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
++              };
++
++              sdmmc_vol_ctrl_h: sdmmc-vol-ctrl-h {
++                      rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
++              };
++      };
++};
++
++&pwm1 {
++      pinctrl-names = "default";
++      pinctrl-0 = <&pwm1m0_pins>;
++      status = "okay";
++};
++
++&pwm2 {
++      pinctrl-names = "default";
++      pinctrl-0 = <&pwm2m0_pins>;
++      status = "okay";
++};
++
++&saradc {
++      vref-supply = <&vcc_1v8>;
++      status = "okay";
++};
++
++&sdhci {
++      bus-width = <8>;
++      cap-mmc-highspeed;
++      mmc-hs200-1_8v;
++      non-removable;
++      vmmc-supply = <&vcc_3v3>;
++      vqmmc-supply = <&vcc_1v8>;
++      status = "okay";
++};
++
++&sdmmc {
++      bus-width = <4>;
++      cap-sd-highspeed;
++      disable-wp;
++      sd-uhs-sdr104;
++      vmmc-supply = <&vcc3v3_sd>;
++      vqmmc-supply = <&vccio_sd>;
++      status = "okay";
++};
++
++&uart0 {
++      pinctrl-names = "default";
++      pinctrl-0 = <&uart0m0_xfer>;
++      status = "okay";
++};
++
++&usb2phy {
++      status = "okay";
++};
++
++&usb2phy_host {
++      phy-supply = <&vcc5v0_sys>;
++      status = "okay";
++};
++
++&usb_host0_ehci {
++      status = "okay";
++};
++
++&usb_host0_ohci {
++      status = "okay";
++};

diff --git a/target/linux/rockchip/patches-6.12/121-arm64-dts-rockchip-add-led-aliases-for-HINLINK.patch b/target/linux/rockchip/patches-6.12/121-arm64-dts-rockchip-add-led-aliases-for-HINLINK.patch
new file mode 100644 (file)
index 0000000..ce70a69
--- /dev/null
+++ b/target/linux/rockchip/patches-6.12/121-arm64-dts-rockchip-add-led-aliases-for-HINLINK.patch
@@ -0,0 +1,23 @@
+--- a/arch/arm64/boot/dts/rockchip/rk3528-hinlink-h28k.dts
++++ b/arch/arm64/boot/dts/rockchip/rk3528-hinlink-h28k.dts
+@@ -16,6 +16,11 @@
+               mmc0 = &sdhci;
+               mmc1 = &sdmmc;
+               serial0 = &uart0;
++
++              led-boot = &led_work;
++              led-failsafe = &led_work;
++              led-running = &led_work;
++              led-upgrade = &led_work;
+       };
+ 
+       chosen {
+@@ -55,7 +60,7 @@
+                       linux,default-trigger = "netdev";
+               };
+ 
+-              led-2 {
++              led_work: led-2 {
+                       color = <LED_COLOR_ID_GREEN>;
+                       function = LED_FUNCTION_STATUS;
+                       gpios = <&gpio4 RK_PB7 GPIO_ACTIVE_LOW>;