// bd71828-regulator.c ROHM BD71828GW-DS1 regulator driver
//
+#include <linux/cleanup.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/mfd/rohm-bd71828.h>
+#include <linux/mfd/rohm-bd72720.h>
#include <linux/module.h>
+#include <linux/mod_devicetable.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/of_regulator.h>
+#define BD72720_MASK_LDON_HEAD GENMASK(2, 0)
struct reg_init {
unsigned int reg;
unsigned int mask;
},
};
+#define BD72720_MASK_DVS_BUCK1_CTRL BIT(4)
+#define BD72720_MASK_DVS_LDO1_CTRL BIT(5)
+
+static const struct reg_init bd72720_buck1_inits[] = {
+ {
+ .reg = BD72720_REG_PS_CTRL_2,
+ .mask = BD72720_MASK_DVS_BUCK1_CTRL,
+ .val = 0, /* Disable "run-level" control */
+ },
+};
+
+static const struct reg_init bd72720_ldo1_inits[] = {
+ {
+ .reg = BD72720_REG_PS_CTRL_2,
+ .mask = BD72720_MASK_DVS_LDO1_CTRL,
+ .val = 0, /* Disable "run-level" control */
+ },
+};
+
+/* BD71828 Buck voltages */
static const struct linear_range bd71828_buck1267_volts[] = {
REGULATOR_LINEAR_RANGE(500000, 0x00, 0xef, 6250),
REGULATOR_LINEAR_RANGE(2000000, 0xf0, 0xff, 0),
REGULATOR_LINEAR_RANGE(3300000, 0x10, 0x1f, 0),
};
+/* BD71828 LDO voltages */
static const struct linear_range bd71828_ldo_volts[] = {
REGULATOR_LINEAR_RANGE(800000, 0x00, 0x31, 50000),
REGULATOR_LINEAR_RANGE(3300000, 0x32, 0x3f, 0),
};
+/* BD72720 Buck voltages */
+static const struct linear_range bd72720_buck1234_volts[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0x00, 0xc0, 6250),
+ REGULATOR_LINEAR_RANGE(1700000, 0xc1, 0xff, 0),
+};
+
+static const struct linear_range bd72720_buck589_volts[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0x00, 0x78, 10000),
+ REGULATOR_LINEAR_RANGE(1700000, 0x79, 0xff, 0),
+};
+
+static const struct linear_range bd72720_buck67_volts[] = {
+ REGULATOR_LINEAR_RANGE(1500000, 0x00, 0xb4, 10000),
+ REGULATOR_LINEAR_RANGE(3300000, 0xb5, 0xff, 0),
+};
+
+/*
+ * The BUCK10 on BD72720 has two modes of operation, depending on a LDON_HEAD
+ * setting. When LDON_HEAD is 0x0, the behaviour is as with other bucks, eg.
+ * voltage can be set to a values indicated below using the VSEL register.
+ *
+ * However, when LDON_HEAD is set to 0x1 ... 0x7, BUCK 10 voltage is, according
+ * to the data-sheet, "automatically adjusted following LDON_HEAD setting and
+ * clamped to BUCK10_VID setting".
+ *
+ * Again, reading the data-sheet shows a "typical connection" where the BUCK10
+ * is used to supply the LDOs 1-4. My assumption is that in practice, this
+ * means that the BUCK10 voltage will be adjusted based on the maximum output
+ * of the LDO 1-4 (to minimize power loss). This makes sense.
+ *
+ * Auto-adjusting regulators aren't something I really like to model in the
+ * driver though - and, if the auto-adjustment works as intended, then there
+ * should really be no need to software to care about the buck10 voltages.
+ * If enable/disable control is still needed, we can implement buck10 as a
+ * regulator with only the enable/disable ops - and device-tree can be used
+ * to model the supply-relations. I believe this could allow the regulator
+ * framework to automagically disable the BUCK10 if all LDOs that are being
+ * supplied by it are disabled.
+ */
+static const struct linear_range bd72720_buck10_volts[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0x00, 0xc0, 6250),
+ REGULATOR_LINEAR_RANGE(1700000, 0xc1, 0xff, 0),
+};
+
+/* BD72720 LDO voltages */
+static const struct linear_range bd72720_ldo1234_volts[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0x00, 0x50, 6250),
+ REGULATOR_LINEAR_RANGE(1000000, 0x51, 0x7f, 0),
+};
+
+static const struct linear_range bd72720_ldo57891011_volts[] = {
+ REGULATOR_LINEAR_RANGE(750000, 0x00, 0xff, 10000),
+};
+
+static const struct linear_range bd72720_ldo6_volts[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0x00, 0x78, 10000),
+ REGULATOR_LINEAR_RANGE(1800000, 0x79, 0x7f, 0),
+};
+
static const unsigned int bd71828_ramp_delay[] = { 2500, 5000, 10000, 20000 };
+/*
+ * BD72720 supports setting both the ramp-up and ramp-down values
+ * separately. Do we need to support ramp-down setting?
+ */
+static const unsigned int bd72720_ramp_delay[] = { 5000, 7500, 10000, 12500 };
+
static int buck_set_hw_dvs_levels(struct device_node *np,
const struct regulator_desc *desc,
struct regulator_config *cfg)
.is_enabled = regulator_is_enabled_regmap,
};
+static const struct regulator_ops bd72720_regulator_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_ramp_delay = regulator_set_ramp_delay_regmap,
+};
+
+static const struct regulator_ops bd72720_buck10_ldon_head_op = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .set_ramp_delay = regulator_set_ramp_delay_regmap,
+};
+
static const struct bd71828_regulator_data bd71828_rdata[] = {
{
.desc = {
},
};
+#define BD72720_BUCK10_DESC_INDEX 10
+#define BD72720_NUM_BUCK_VOLTS 0x100
+#define BD72720_NUM_LDO_VOLTS 0x100
+#define BD72720_NUM_LDO12346_VOLTS 0x80
+
+static const struct bd71828_regulator_data bd72720_rdata[] = {
+ {
+ .desc = {
+ .name = "buck1",
+ .of_match = of_match_ptr("buck1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_BUCK1,
+ .type = REGULATOR_VOLTAGE,
+
+ /*
+ * The BD72720 BUCK1 and LDO1 support GPIO toggled
+ * sub-RUN states called RUN0, RUN1, RUN2 and RUN3.
+ * The "operating mode" (sub-RUN states or normal)
+ * can be changed by a register.
+ *
+ * When the sub-RUN states are used, the voltage and
+ * enable state depend on a state specific
+ * configuration. The voltage and enable configuration
+ * for BUCK1 and LDO1 can be defined for each sub-RUN
+ * state using BD72720_REG_[BUCK,LDO]1_VSEL_R[0,1,2,3]
+ * voltage selection registers and the bits
+ * BD72720_MASK_RUN_[0,1,2,3]_EN in the enable registers.
+ * The PMIC will change both the BUCK1 and LDO1 voltages
+ * to the states defined in these registers when
+ * "DVS GPIOs" are toggled.
+ *
+ * If RUN 0 .. RUN 4 states are to be used, the normal
+ * voltage configuration mechanisms do not apply
+ * and we should overwrite the ops and ignore the
+ * voltage setting/getting registers which are setup
+ * here. This is not supported for now. If you need
+ * this functionality, you may try merging functionality
+ * from a downstream driver:
+ * https://rohmsemiconductor.github.io/Linux-Kernel-PMIC-Drivers/BD72720/
+ */
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_buck1234_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_buck1234_volts),
+ .n_voltages = BD72720_NUM_BUCK_VOLTS,
+ .enable_reg = BD72720_REG_BUCK1_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_BUCK1_VSEL_RB,
+ .vsel_mask = BD72720_MASK_BUCK_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_BUCK1_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR, /* Deep idle in data-sheet */
+ .run_reg = BD72720_REG_BUCK1_VSEL_RB,
+ .run_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_reg = BD72720_REG_BUCK1_VSEL_I,
+ .idle_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_reg = BD72720_REG_BUCK1_VSEL_S,
+ .suspend_mask = BD72720_MASK_BUCK_VSEL,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_reg = BD72720_REG_BUCK1_VSEL_DI,
+ .lpsr_mask = BD72720_MASK_BUCK_VSEL,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ .reg_inits = bd72720_buck1_inits,
+ .reg_init_amnt = ARRAY_SIZE(bd72720_buck1_inits),
+ }, {
+ .desc = {
+ .name = "buck2",
+ .of_match = of_match_ptr("buck2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_BUCK2,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_buck1234_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_buck1234_volts),
+ .n_voltages = BD72720_NUM_BUCK_VOLTS,
+ .enable_reg = BD72720_REG_BUCK2_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_BUCK2_VSEL_R,
+ .vsel_mask = BD72720_MASK_BUCK_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_BUCK2_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_BUCK2_VSEL_R,
+ .run_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_reg = BD72720_REG_BUCK2_VSEL_I,
+ .idle_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_reg = BD72720_REG_BUCK2_VSEL_S,
+ .suspend_mask = BD72720_MASK_BUCK_VSEL,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_reg = BD72720_REG_BUCK2_VSEL_DI,
+ .lpsr_mask = BD72720_MASK_BUCK_VSEL,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "buck3",
+ .of_match = of_match_ptr("buck3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_BUCK3,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_buck1234_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_buck1234_volts),
+ .n_voltages = BD72720_NUM_BUCK_VOLTS,
+ .enable_reg = BD72720_REG_BUCK3_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_BUCK3_VSEL_R,
+ .vsel_mask = BD72720_MASK_BUCK_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_BUCK3_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_BUCK3_VSEL_R,
+ .run_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_reg = BD72720_REG_BUCK3_VSEL_I,
+ .idle_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_reg = BD72720_REG_BUCK3_VSEL_S,
+ .suspend_mask = BD72720_MASK_BUCK_VSEL,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_reg = BD72720_REG_BUCK3_VSEL_DI,
+ .lpsr_mask = BD72720_MASK_BUCK_VSEL,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "buck4",
+ .of_match = of_match_ptr("buck4"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_BUCK4,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_buck1234_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_buck1234_volts),
+ .n_voltages = BD72720_NUM_BUCK_VOLTS,
+ .enable_reg = BD72720_REG_BUCK4_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_BUCK4_VSEL_R,
+ .vsel_mask = BD72720_MASK_BUCK_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_BUCK4_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_BUCK4_VSEL_R,
+ .run_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_reg = BD72720_REG_BUCK4_VSEL_I,
+ .idle_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_reg = BD72720_REG_BUCK4_VSEL_S,
+ .suspend_mask = BD72720_MASK_BUCK_VSEL,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_reg = BD72720_REG_BUCK4_VSEL_DI,
+ .lpsr_mask = BD72720_MASK_BUCK_VSEL,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "buck5",
+ .of_match = of_match_ptr("buck5"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_BUCK5,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_buck589_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_buck589_volts),
+ .n_voltages = BD72720_NUM_BUCK_VOLTS,
+ .enable_reg = BD72720_REG_BUCK5_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_BUCK5_VSEL,
+ .vsel_mask = BD72720_MASK_BUCK_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_BUCK5_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_BUCK5_VSEL,
+ .run_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "buck6",
+ .of_match = of_match_ptr("buck6"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_BUCK6,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_buck67_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_buck67_volts),
+ .n_voltages = BD72720_NUM_BUCK_VOLTS,
+ .enable_reg = BD72720_REG_BUCK6_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_BUCK6_VSEL,
+ .vsel_mask = BD72720_MASK_BUCK_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_BUCK6_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_BUCK6_VSEL,
+ .run_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "buck7",
+ .of_match = of_match_ptr("buck7"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_BUCK7,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_buck67_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_buck67_volts),
+ .n_voltages = BD72720_NUM_BUCK_VOLTS,
+ .enable_reg = BD72720_REG_BUCK7_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_BUCK7_VSEL,
+ .vsel_mask = BD72720_MASK_BUCK_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_BUCK7_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_BUCK7_VSEL,
+ .run_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "buck8",
+ .of_match = of_match_ptr("buck8"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_BUCK8,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_buck589_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_buck589_volts),
+ .n_voltages = BD72720_NUM_BUCK_VOLTS,
+ .enable_reg = BD72720_REG_BUCK8_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_BUCK8_VSEL,
+ .vsel_mask = BD72720_MASK_BUCK_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_BUCK8_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_BUCK8_VSEL,
+ .run_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "buck9",
+ .of_match = of_match_ptr("buck9"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_BUCK9,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_buck589_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_buck589_volts),
+ .n_voltages = BD72720_NUM_BUCK_VOLTS,
+ .enable_reg = BD72720_REG_BUCK9_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_BUCK9_VSEL,
+ .vsel_mask = BD72720_MASK_BUCK_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_BUCK9_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_BUCK9_VSEL,
+ .run_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "buck10",
+ .of_match = of_match_ptr("buck10"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_BUCK10,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_buck10_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_buck10_volts),
+ .n_voltages = BD72720_NUM_BUCK_VOLTS,
+ .enable_reg = BD72720_REG_BUCK10_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_BUCK10_VSEL,
+ .vsel_mask = BD72720_MASK_BUCK_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_BUCK10_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_BUCK10_VSEL,
+ .run_mask = BD72720_MASK_BUCK_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "ldo1",
+ .of_match = of_match_ptr("ldo1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_LDO1,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_ldo1234_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_ldo1234_volts),
+ .n_voltages = BD72720_NUM_LDO12346_VOLTS,
+ .enable_reg = BD72720_REG_LDO1_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_LDO1_VSEL_RB,
+ .vsel_mask = BD72720_MASK_LDO12346_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_LDO1_MODE1,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_LDO1_VSEL_RB,
+ .run_mask = BD72720_MASK_LDO12346_VSEL,
+ .idle_reg = BD72720_REG_LDO1_VSEL_I,
+ .idle_mask = BD72720_MASK_LDO12346_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_reg = BD72720_REG_LDO1_VSEL_S,
+ .suspend_mask = BD72720_MASK_LDO12346_VSEL,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_reg = BD72720_REG_LDO1_VSEL_DI,
+ .lpsr_mask = BD72720_MASK_LDO12346_VSEL,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ .reg_inits = bd72720_ldo1_inits,
+ .reg_init_amnt = ARRAY_SIZE(bd72720_ldo1_inits),
+ }, {
+ .desc = {
+ .name = "ldo2",
+ .of_match = of_match_ptr("ldo2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_LDO2,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_ldo1234_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_ldo1234_volts),
+ .n_voltages = BD72720_NUM_LDO12346_VOLTS,
+ .enable_reg = BD72720_REG_LDO2_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_LDO2_VSEL_R,
+ .vsel_mask = BD72720_MASK_LDO12346_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_LDO2_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_LDO2_VSEL_R,
+ .run_mask = BD72720_MASK_LDO12346_VSEL,
+ .idle_reg = BD72720_REG_LDO2_VSEL_I,
+ .idle_mask = BD72720_MASK_LDO12346_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_reg = BD72720_REG_LDO2_VSEL_S,
+ .suspend_mask = BD72720_MASK_LDO12346_VSEL,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_reg = BD72720_REG_LDO2_VSEL_DI,
+ .lpsr_mask = BD72720_MASK_LDO12346_VSEL,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "ldo3",
+ .of_match = of_match_ptr("ldo3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_LDO3,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_ldo1234_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_ldo1234_volts),
+ .n_voltages = BD72720_NUM_LDO12346_VOLTS,
+ .enable_reg = BD72720_REG_LDO3_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_LDO3_VSEL_R,
+ .vsel_mask = BD72720_MASK_LDO12346_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_LDO3_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_LDO3_VSEL_R,
+ .run_mask = BD72720_MASK_LDO12346_VSEL,
+ .idle_reg = BD72720_REG_LDO3_VSEL_I,
+ .idle_mask = BD72720_MASK_LDO12346_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_reg = BD72720_REG_LDO3_VSEL_S,
+ .suspend_mask = BD72720_MASK_LDO12346_VSEL,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_reg = BD72720_REG_LDO3_VSEL_DI,
+ .lpsr_mask = BD72720_MASK_LDO12346_VSEL,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "ldo4",
+ .of_match = of_match_ptr("ldo4"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_LDO4,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_ldo1234_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_ldo1234_volts),
+ .n_voltages = BD72720_NUM_LDO12346_VOLTS,
+ .enable_reg = BD72720_REG_LDO4_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_LDO4_VSEL_R,
+ .vsel_mask = BD72720_MASK_LDO12346_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_LDO4_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_LDO4_VSEL_R,
+ .run_mask = BD72720_MASK_LDO12346_VSEL,
+ .idle_reg = BD72720_REG_LDO4_VSEL_I,
+ .idle_mask = BD72720_MASK_LDO12346_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_reg = BD72720_REG_LDO4_VSEL_S,
+ .suspend_mask = BD72720_MASK_LDO12346_VSEL,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_reg = BD72720_REG_LDO4_VSEL_DI,
+ .lpsr_mask = BD72720_MASK_LDO12346_VSEL,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "ldo5",
+ .of_match = of_match_ptr("ldo5"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_LDO5,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_ldo57891011_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_ldo57891011_volts),
+ .n_voltages = BD72720_NUM_LDO_VOLTS,
+ .enable_reg = BD72720_REG_LDO5_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_LDO5_VSEL,
+ .vsel_mask = BD72720_MASK_LDO_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_LDO5_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_LDO5_VSEL,
+ .run_mask = BD72720_MASK_LDO_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "ldo6",
+ .of_match = of_match_ptr("ldo6"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_LDO6,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_ldo6_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_ldo6_volts),
+ .n_voltages = BD72720_NUM_LDO12346_VOLTS,
+ .enable_reg = BD72720_REG_LDO6_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_LDO6_VSEL,
+ .vsel_mask = BD72720_MASK_LDO12346_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_LDO6_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_LDO6_VSEL,
+ .run_mask = BD72720_MASK_LDO12346_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "ldo7",
+ .of_match = of_match_ptr("ldo7"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_LDO7,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_ldo57891011_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_ldo57891011_volts),
+ .n_voltages = BD72720_NUM_LDO_VOLTS,
+ .enable_reg = BD72720_REG_LDO7_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_LDO7_VSEL,
+ .vsel_mask = BD72720_MASK_LDO_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_LDO7_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_LDO7_VSEL,
+ .run_mask = BD72720_MASK_LDO_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "ldo8",
+ .of_match = of_match_ptr("ldo8"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_LDO8,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_ldo57891011_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_ldo57891011_volts),
+ .n_voltages = BD72720_NUM_LDO_VOLTS,
+ .enable_reg = BD72720_REG_LDO8_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_LDO8_VSEL,
+ .vsel_mask = BD72720_MASK_LDO_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_LDO8_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_LDO8_VSEL,
+ .run_mask = BD72720_MASK_LDO_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "ldo9",
+ .of_match = of_match_ptr("ldo9"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_LDO9,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_ldo57891011_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_ldo57891011_volts),
+ .n_voltages = BD72720_NUM_LDO_VOLTS,
+ .enable_reg = BD72720_REG_LDO9_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_LDO9_VSEL,
+ .vsel_mask = BD72720_MASK_LDO_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_LDO9_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_LDO9_VSEL,
+ .run_mask = BD72720_MASK_LDO_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "ldo10",
+ .of_match = of_match_ptr("ldo10"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_LDO10,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_ldo57891011_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_ldo57891011_volts),
+ .n_voltages = BD72720_NUM_LDO_VOLTS,
+ .enable_reg = BD72720_REG_LDO10_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_LDO10_VSEL,
+ .vsel_mask = BD72720_MASK_LDO_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_LDO10_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_LDO10_VSEL,
+ .run_mask = BD72720_MASK_LDO_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ }, {
+ .desc = {
+ .name = "ldo11",
+ .of_match = of_match_ptr("ldo11"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD72720_LDO11,
+ .type = REGULATOR_VOLTAGE,
+ .ops = &bd72720_regulator_ops,
+ .linear_ranges = bd72720_ldo57891011_volts,
+ .n_linear_ranges = ARRAY_SIZE(bd72720_ldo57891011_volts),
+ .n_voltages = BD72720_NUM_LDO_VOLTS,
+ .enable_reg = BD72720_REG_LDO11_ON,
+ .enable_mask = BD72720_MASK_RUN_B_EN,
+ .vsel_reg = BD72720_REG_LDO11_VSEL,
+ .vsel_mask = BD72720_MASK_LDO_VSEL,
+
+ .ramp_delay_table = bd72720_ramp_delay,
+ .n_ramp_values = ARRAY_SIZE(bd72720_ramp_delay),
+ .ramp_reg = BD72720_REG_LDO11_MODE,
+ .ramp_mask = BD72720_MASK_RAMP_UP_DELAY,
+ .owner = THIS_MODULE,
+ .of_parse_cb = buck_set_hw_dvs_levels,
+ },
+ .dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+ ROHM_DVS_LEVEL_SUSPEND |
+ ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD72720_REG_LDO11_VSEL,
+ .run_mask = BD72720_MASK_LDO_VSEL,
+ .idle_on_mask = BD72720_MASK_IDLE_EN,
+ .suspend_on_mask = BD72720_MASK_SUSPEND_EN,
+ .lpsr_on_mask = BD72720_MASK_DEEP_IDLE_EN,
+ },
+ },
+};
+
+static int bd72720_buck10_ldon_head_mode(struct device *dev,
+ struct device_node *npreg,
+ struct regmap *regmap,
+ struct regulator_desc *buck10_desc)
+{
+ struct device_node *np __free(device_node) =
+ of_get_child_by_name(npreg, "buck10");
+ uint32_t ldon_head;
+ int ldon_val;
+ int ret;
+
+ if (!np) {
+ dev_err(dev, "failed to find buck10 regulator node\n");
+ return -ENODEV;
+ }
+
+ ret = of_property_read_u32(np, "rohm,ldon-head-microvolt", &ldon_head);
+ if (ret == -EINVAL)
+ return 0;
+ if (ret)
+ return ret;
+
+ /*
+ * LDON_HEAD mode means the BUCK10 is used to supply LDOs 1-4 and
+ * the BUCK 10 voltage is automatically set to follow LDO 1-4
+ * settings. Thus the BUCK10 should not allow voltage [g/s]etting.
+ */
+ buck10_desc->ops = &bd72720_buck10_ldon_head_op;
+
+ ldon_val = ldon_head / 50000 + 1;
+ if (ldon_head > 300000) {
+ dev_warn(dev, "Unsupported LDON_HEAD, clamping to 300 mV\n");
+ ldon_val = 7;
+ }
+
+ return regmap_update_bits(regmap, BD72720_REG_LDO1_MODE2,
+ BD72720_MASK_LDON_HEAD, ldon_val);
+}
+
+static int bd72720_dt_parse(struct device *dev,
+ struct regulator_desc *buck10_desc,
+ struct regmap *regmap)
+{
+ struct device_node *nproot __free(device_node) =
+ of_get_child_by_name(dev->parent->of_node, "regulators");
+
+ if (!nproot) {
+ dev_err(dev, "failed to find regulators node\n");
+ return -ENODEV;
+ }
+
+ return bd72720_buck10_ldon_head_mode(dev, nproot, regmap, buck10_desc);
+}
+
static int bd71828_probe(struct platform_device *pdev)
{
- int i, j, ret;
+ int i, j, ret, num_regulators;
struct regulator_config config = {
.dev = pdev->dev.parent,
};
+ enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data;
+ struct bd71828_regulator_data *rdata;
config.regmap = dev_get_regmap(pdev->dev.parent, NULL);
if (!config.regmap)
return -ENODEV;
- for (i = 0; i < ARRAY_SIZE(bd71828_rdata); i++) {
+ switch (chip) {
+ case ROHM_CHIP_TYPE_BD72720:
+ rdata = devm_kmemdup(&pdev->dev, bd72720_rdata,
+ sizeof(bd72720_rdata), GFP_KERNEL);
+ if (!rdata)
+ return -ENOMEM;
+
+ ret = bd72720_dt_parse(&pdev->dev, &rdata[BD72720_BUCK10_DESC_INDEX].desc,
+ config.regmap);
+ if (ret)
+ return ret;
+
+ num_regulators = ARRAY_SIZE(bd72720_rdata);
+ break;
+
+ case ROHM_CHIP_TYPE_BD71828:
+ rdata = devm_kmemdup(&pdev->dev, bd71828_rdata,
+ sizeof(bd71828_rdata), GFP_KERNEL);
+ if (!rdata)
+ return -ENOMEM;
+
+ num_regulators = ARRAY_SIZE(bd71828_rdata);
+
+ break;
+ default:
+ return dev_err_probe(&pdev->dev, -EINVAL,
+ "Unsupported device\n");
+ }
+
+ for (i = 0; i < num_regulators; i++) {
struct regulator_dev *rdev;
- const struct bd71828_regulator_data *rd;
+ struct bd71828_regulator_data *rd;
+
+ rd = &rdata[i];
- rd = &bd71828_rdata[i];
+ config.driver_data = rd;
rdev = devm_regulator_register(&pdev->dev,
&rd->desc, &config);
if (IS_ERR(rdev))
return 0;
}
+static const struct platform_device_id bd71828_pmic_id[] = {
+ { "bd71828-pmic", ROHM_CHIP_TYPE_BD71828 },
+ { "bd72720-pmic", ROHM_CHIP_TYPE_BD72720 },
+ { },
+};
+MODULE_DEVICE_TABLE(platform, bd71828_pmic_id);
+
static struct platform_driver bd71828_regulator = {
.driver = {
.name = "bd71828-pmic",
.probe_type = PROBE_PREFER_ASYNCHRONOUS,
},
.probe = bd71828_probe,
+ .id_table = bd71828_pmic_id,
};
module_platform_driver(bd71828_regulator);
MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
MODULE_DESCRIPTION("BD71828 voltage regulator driver");
MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:bd71828-pmic");
projects / thirdparty / kernel / linux.git / commitdiff
