]> git.ipfire.org Git - thirdparty/openwrt.git/commitdiff
mediatek: add support for ipTIME AX3000SM 18689/head
authorDonghyun Ko <nyankosoftware@gmail.com>
Sat, 3 May 2025 00:24:10 +0000 (09:24 +0900)
committerHauke Mehrtens <hauke@hauke-m.de>
Sun, 13 Jul 2025 15:26:01 +0000 (17:26 +0200)
Specification
-------------
- SoC       : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM       : DDR3 256Mbytes, Nanya Technology NT5CC128M16IP
- Flash     : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN      : MediaTek MT7976CN dual-band Wi-Fi 6
  - 2.4GHz  : b/g/n/ax, MU-MIMO
  - 5GHz    : a/n/ac/ax, MU-MIMO
- Ethernet  : 10/100/1000 Mbps x4, LAN (MediaTek MT7531AE)
              10/100/1000 Mbps x1, WAN (MT7981 internal PHY)
- UART      : 1x4 pin header on PCB
  - [J500] 3.3V, TX, RX, GND (115200, 8N1)
- Buttons   : WPS, Reset
- LEDs      : 1x Power (Amber)
              1x CPU (Amber)
              1x Wi-Fi 5GHz (Amber)
              1x Wi-Fi 2.4GHz (Amber)
              1x WAN activity (Amber)
              4x LAN activity (Amber)
- Power     : 12VDC, 1A (Center positive polarity)

MAC address
-----------
+-----------+-------------------+-----------+
| Interface | MAC               | Algorithm |
+-----------+-------------------+-----------+
| WLAN 2.4G | B0:38:6C:xx:xx:xx | label     |
| WLAN 5G   | B2:38:6C:4x:xx:xx |           |
| WAN       | B0:38:6C:xx:xx:xx | label + 1 |
| LAN       | B0:38:6C:xx:xx:xx | label + 3 |
+-----------+-------------------+-----------+
The WLAN 2.4G MAC address was found in 'Factory' partition, 0x4

Installation
------------
1. Download the *initramfs-kernel.bin file from the OpenWrt website
2. Attach UART to the router, and interrupt the boot process by pressing '0'

   If you successfully interrupt the boot process, a terminal prompt
   name should look like this:

   MT7981>

3. Connect the router(LAN port) to the PC
4. Assign the PC IP address: 192.168.0.100/24
5. Load and run the *initramfs-kernel.bin:

  tftpboot 0x46000000 initramfs-kernel.bin
  bootm

6. Upload the OpenWrt *squashfs-sysupgrade.bin to the router
7. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18689
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
target/linux/mediatek/dts/mt7981b-iptime-ax3000sm.dts [new file with mode: 0644]
target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
target/linux/mediatek/filogic/base-files/etc/board.d/02_network
target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
target/linux/mediatek/image/filogic.mk

diff --git a/target/linux/mediatek/dts/mt7981b-iptime-ax3000sm.dts b/target/linux/mediatek/dts/mt7981b-iptime-ax3000sm.dts
new file mode 100644 (file)
index 0000000..1b1ba3d
--- /dev/null
@@ -0,0 +1,279 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "mt7981b.dtsi"
+
+/ {
+       model = "ipTIME AX3000SM";
+       compatible = "iptime,ax3000sm", "mediatek,mt7981";
+
+       aliases {
+               serial0 = &uart0;
+               label-mac-device = &gmac1;
+               led-boot = &led_cpu;
+               led-failsafe = &led_cpu;
+               led-running = &led_cpu;
+               led-upgrade = &led_cpu;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys";
+
+               button-0 {
+                       label = "wps";
+                       gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+                       debounce-interval = <60>;
+               };
+
+               button-1 {
+                       label = "reset";
+                       gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+                       debounce-interval = <60>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led-0 {
+                       color = <LED_COLOR_ID_AMBER>;
+                       function = LED_FUNCTION_WAN;
+                       gpios = <&pio 8 GPIO_ACTIVE_LOW>;
+               };
+
+               led-1 {
+                       color = <LED_COLOR_ID_AMBER>;
+                       function = LED_FUNCTION_WLAN_2GHZ;
+                       gpios = <&pio 34 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0tpt";
+               };
+
+               led-2 {
+                       color = <LED_COLOR_ID_AMBER>;
+                       function = LED_FUNCTION_WLAN_5GHZ;
+                       gpios = <&pio 35 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy1tpt";
+               };
+
+               led_cpu: led-3 {
+                       color = <LED_COLOR_ID_AMBER>;
+                       function = LED_FUNCTION_CPU;
+                       gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
+               };
+       };
+};
+
+&eth {
+       status = "okay";
+
+       gmac0: mac@0 {
+               compatible = "mediatek,eth-mac";
+               reg = <0>;
+               phy-mode = "2500base-x";
+
+               nvmem-cell-names = "mac-address";
+               nvmem-cells = <&macaddr_factory_4 (3)>;
+
+               fixed-link {
+                       speed = <2500>;
+                       full-duplex;
+                       pause;
+               };
+       };
+
+       gmac1: mac@1 {
+               compatible = "mediatek,eth-mac";
+               reg = <1>;
+               phy-mode = "gmii";
+               phy-handle = <&int_gbe_phy>;
+
+               nvmem-cell-names = "mac-address";
+               nvmem-cells = <&macaddr_factory_4 (1)>;
+       };
+};
+
+&mdio_bus {
+       switch: switch@1f {
+               compatible = "mediatek,mt7531";
+               reg = <0x1f>;
+               reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+               interrupt-controller;
+               #interrupt-cells = <1>;
+               interrupt-parent = <&pio>;
+               interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+       };
+};
+
+&spi0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&spi0_flash_pins>;
+       status = "okay";
+
+       spi_nand@0 {
+               #address-cells = <1>;
+               #size-cells = <1>;
+               compatible = "spi-nand";
+               reg = <0>;
+
+               spi-max-frequency = <52000000>;
+               spi-tx-buswidth = <4>;
+               spi-rx-buswidth = <4>;
+
+               spi-cal-enable;
+               spi-cal-mode = "read-data";
+               spi-cal-datalen = <7>;
+               spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>;
+               spi-cal-addrlen = <5>;
+               spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+               mediatek,nmbm;
+               mediatek,bmt-max-ratio = <1>;
+               mediatek,bmt-max-reserved-blocks = <64>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "BL2";
+                               reg = <0x0 0x100000>;
+                               read-only;
+                       };
+
+                       partition@100000 {
+                               label = "u-boot-env";
+                               reg = <0x100000 0x80000>;
+                       };
+
+                       partition@180000 {
+                               label = "Factory";
+                               reg = <0x180000 0x200000>;
+                               read-only;
+
+                               nvmem-layout {
+                                       compatible = "fixed-layout";
+                                       #address-cells = <1>;
+                                       #size-cells = <1>;
+
+                                       eeprom_factory_0: eeprom@0 {
+                                               reg = <0x0 0x1000>;
+                                       };
+
+                                       macaddr_factory_4: macaddr@4 {
+                                               compatible = "mac-base";
+                                               reg = <0x4 0x6>;
+                                               #nvmem-cell-cells = <1>;
+                                       };
+                               };
+                       };
+
+                       partition@380000 {
+                               label = "FIP";
+                               reg = <0x380000 0x200000>;
+                               read-only;
+                       };
+
+                       partition@580000 {
+                               label = "ubi";
+                               reg = <0x580000 0x6E00000>;
+                       };
+               };
+       };
+};
+
+&switch {
+       ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               port@0 {
+                       reg = <0>;
+                       label = "lan4";
+               };
+
+               port@1 {
+                       reg = <1>;
+                       label = "lan3";
+               };
+
+               port@2 {
+                       reg = <2>;
+                       label = "lan2";
+               };
+
+               port@3 {
+                       reg = <3>;
+                       label = "lan1";
+               };
+
+               port@6 {
+                       reg = <6>;
+                       ethernet = <&gmac0>;
+                       phy-mode = "2500base-x";
+
+                       fixed-link {
+                               speed = <2500>;
+                               full-duplex;
+                               pause;
+                       };
+               };
+       };
+};
+
+&pio {
+       spi0_flash_pins: spi0-pins {
+               mux {
+                       function = "spi";
+                       groups = "spi0", "spi0_wp_hold";
+               };
+
+               conf-pu {
+                       pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+                       drive-strength = <MTK_DRIVE_4mA>;
+                       bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+               };
+
+               conf-pd {
+                       pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+                       drive-strength = <MTK_DRIVE_4mA>;
+                       bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+               };
+       };
+};
+
+&uart0 {
+       status = "okay";
+};
+
+&watchdog {
+       status = "okay";
+};
+
+&wifi {
+       status = "okay";
+       nvmem-cell-names = "eeprom";
+       nvmem-cells = <&eeprom_factory_0>;
+
+       band@0 {
+               reg = <0>;
+               nvmem-cells = <&macaddr_factory_4 (0)>;
+               nvmem-cell-names = "mac-address";
+       };
+
+       band@1 {
+               reg = <1>;
+               nvmem-cells = <&macaddr_factory_4 (0)>;
+               nvmem-cell-names = "mac-address";
+       };
+};
index 53df9106f2d9cfe6fc8758aa82343301737ec5ba..852c17b90275570aa4eff3b754dc1aa5d30e5853 100644 (file)
@@ -78,6 +78,9 @@ glinet,gl-xe3000)
 huasifei,wh3000)
        ucidef_set_led_netdev "wan" "WAN" "red:wan" "eth1" "link tx rx"
        ;;
+iptime,ax3000sm)
+       ucidef_set_led_netdev "wan" "wan" "amber:wan" "eth1" "link tx rx"
+       ;;
 mercusys,mr80x-v3)
        ucidef_set_led_netdev "lan1" "lan-1" "green:lan-1" "lan1" "link tx rx"
        ucidef_set_led_netdev "lan2" "lan-2" "green:lan-2" "lan2" "link tx rx"
index 453594c5e05bcc5cc5f3b62b690a9c51df8a78f0..f9b7440664c28cc4f8a1aa1b4217695042bbfbdb 100644 (file)
@@ -49,6 +49,7 @@ mediatek_setup_interfaces()
                ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan
                ;;
        asus,tuf-ax4200|\
+       iptime,ax3000sm|\
        jdcloud,re-cp-03|\
        mediatek,mt7981-rfb|\
        netcore,n60|\
index 04ec47ee140239b6efd71bd52582ed7f1acd589a..56ae87a0ed6062a4217227d5bdcaa467a45f5655 100644 (file)
@@ -109,6 +109,11 @@ case "$board" in
                [ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress
                [ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress
                ;;
+       iptime,ax3000sm)
+               addr=$(mtd_get_mac_binary "Factory" 0x4)
+               [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_unsetbit $(macaddr_unsetbit $(macaddr_unsetbit $(macaddr_setbit $addr 26) 25) 27) 28) > \
+                       /sys${DEVPATH}/macaddress
+               ;;
        jcg,q30-pro|\
        netcore,n60|\
        netcore,n60-pro)
index c4fce71ae8d0e965fcea1070340d3fb333d90698..d3e94592793e36182fd80ec36b66a3b55bda6978 100644 (file)
@@ -1101,6 +1101,17 @@ define Device/huasifei_wh3000-pro
 endef
 TARGET_DEVICES += huasifei_wh3000-pro
 
+define Device/iptime_ax3000sm
+  DEVICE_VENDOR := ipTIME
+  DEVICE_MODEL := AX3000SM
+  DEVICE_DTS := mt7981b-iptime-ax3000sm
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+  SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-rfb
+endef
+TARGET_DEVICES += iptime_ax3000sm
+
 define Device/jcg_q30-pro
   DEVICE_VENDOR := JCG
   DEVICE_MODEL := Q30 PRO