ramips: mt76x8: add support for Cudy LT400E v1

This commit adds support for the Cudy LT400E v1,
an indoor 4G/LTE WiFi router.
It has 4x10/100 Mbps Ethernet ports, a 2.4 GHz radio,
and a Quectel 4G/LTE EC200A modem.

Hardware:

SoC: MediaTek MT7628NN
Flash: 8 MiB SPI
RAM: 64 MiB
Ethernet: 4x10/100 Mbps
WiFi: 2.4 GHz (embedded MT7628, 802.11n)
WWAN: Quectel EC200A-EL 4G/LTE Cat 4 modem
SIM: nano-SIM slot
Buttons: 1 Reset button, 1 WPS button
LEDs: 10x (blue)
Power: 12 V DC barrel jack

Installation:
The stock firmware is a customized variant of OpenWrt, which implements
a signature check that only allows flashing official firmware. Cudy
offers, on their website [1][6], intermediate OpenWrt firmware images
which do not implement the signature check. After flashing the
intermediate image, the upstream (i.e., official) OpenWrt image can be
installed.  See the device's entry in OpenWrt's Wiki for more details [2].

Cellular network:
The Quectel EC200A modem is internally connected to the SoC via USB, and
operates in ECM mode, supported by the CDC Ether driver [3]. When
inserting a SIM card in the slot, if no PIN is needed, the network
interface "usb0" is brought up and the cellular connection works out of
the box. To interact with the modem directly (unlock the PIN, change APN
and PDP settings, etc.), AT commands can be sent with picocom to serial
port /dev/ttyUSB2 [4].

Recovery:
The stock firmware can be recovered via TFTP, as the bootloader (based
on U-Boot) implements a recovery client. Set up a TFTP server on your
computer with IP 192.168.88.1/24 serving the stock firmware from Cudy's
website renamed to "recovery.bin". Press the Reset button (keep it
pressed), power on the device, wait for the TFTP server to send the
recovery.bin file, then release the Reset button. The router will take a
couple of minutes to reboot and set up the stock firmware. See the
device's entry in OpenWrt's Wiki for more details [2].

Discussion:
Use the dedicated thread in OpenWrt's forum to discuss any aspects [5].

Acknowledgments:
The code to support this device is largely based on the sources kindly
provided by Cudy in compliance with the GPL license. Thanks for
supporting the OpenWrt community.

Links:
[1] https://www.cudy.com/blogs/faq/openwrt-software-download
[2] https://openwrt.org/toh/cudy/lt400e_v1
[3] https://openwrt.org/docs/guide-user/network/wan/wwan/ethernetoverusb_cdc
[4] https://openwrt.org/docs/guide-user/network/wan/wwan/at_commands
[5] https://forum.openwrt.org/t/242466
[6] https://drive.google.com/drive/folders/1BKVarlwlNxf7uJUtRhuMGUqeCa5KpMnj

Co-authored-by: rogerpueyo <roger.pueyo@guifi.net>
Signed-off-by: Kamil Jońca <kjonca@onet.pl>
Link: https://github.com/openwrt/openwrt/pull/21246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

diff --git a/target/linux/ramips/dts/mt7628an_cudy_lt400e-v1.dts b/target/linux/ramips/dts/mt7628an_cudy_lt400e-v1.dts
new file mode 100644 (file)
index 0000000..5ced75c
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_cudy_lt400e-v1.dts
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+       compatible = "cudy,lt400e-v1", "mediatek,mt7628an-soc";
+       model = "Cudy LT400E v1";
+
+       aliases {
+               led-boot = &led_power;
+               led-running = &led_power;
+               led-failsafe = &led_power;
+               led-upgrade = &led_power;
+               label-mac-device = &ethernet;
+       };
+
+       chosen {
+               bootargs = "console=ttyS0,115200";
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_power: power {
+                       function = LED_FUNCTION_POWER;
+                       color = <LED_COLOR_ID_BLUE>;
+                       gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
+               };
+
+               internet {
+                       function = LED_FUNCTION_MOBILE;
+                       color = <LED_COLOR_ID_BLUE>;
+                       gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
+               };
+
+               wifi {
+                       function = LED_FUNCTION_WLAN;
+                       color = <LED_COLOR_ID_BLUE>;
+                       gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+               };
+
+               lan1 {
+                       function = LED_FUNCTION_LAN;
+                       color = <LED_COLOR_ID_BLUE>;
+                       function-enumerator = <1>;
+                       gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+               };
+
+               lan2 {
+                       function = LED_FUNCTION_LAN;
+                       color = <LED_COLOR_ID_BLUE>;
+                       function-enumerator = <2>;
+                       gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
+               };
+
+               lan3 {
+                       function = LED_FUNCTION_LAN;
+                       color = <LED_COLOR_ID_BLUE>;
+                       function-enumerator = <3>;
+                       gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
+               };
+
+               lan4 {
+                       function = LED_FUNCTION_LAN;
+                       color = <LED_COLOR_ID_BLUE>;
+                       function-enumerator = <4>;
+                       gpios = <&gpio 45 GPIO_ACTIVE_LOW>;
+               };
+
+               signal1 {
+                       label = "blue:signal1";
+                       gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+               };
+
+               signal2 {
+                       label = "blue:signal2";
+                       gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+               };
+
+               led-signal3 {
+                       label = "blue:signal3";
+                       gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       gpio-export {
+               compatible = "gpio-export";
+
+               usb4g {
+                       gpio-export,name = "4g";
+                       gpio-export,output = <0>;
+                       gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
+               };
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+       };
+};
+
+
+&state_default {
+       gpio {
+               groups = "i2c", "gpio", "wdt", "p0led_an", "wled_an";
+               function = "gpio";
+       };
+};
+
+&pcie0 {
+       wifi@0,0 {
+               compatible = "mediatek,mt76";
+               reg = <0x0000 0 0 0 0>;
+               nvmem-cells = <&eeprom_factory_8000>, <&macaddr_bdinfo_de00 2>;
+               nvmem-cell-names = "eeprom", "mac-address";
+               ieee80211-freq-limit = <5000000 6000000>;
+       };
+};
+
+&wmac {
+       status = "okay";
+
+       nvmem-cells = <&eeprom_factory_0>, <&macaddr_bdinfo_de00 0>;
+       nvmem-cell-names = "eeprom", "mac-address";
+};
+
+&ethernet {
+       nvmem-cells = <&macaddr_bdinfo_de00 0>;
+       nvmem-cell-names = "mac-address";
+};
+
+&ehci {
+       status = "okay";
+};
+
+&ohci {
+       status = "okay";
+};
+
+&spi0 {
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <40000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x0 0x30000>;
+                               read-only;
+                       };
+
+                       partition@30000 {
+                               label = "u-boot-env";
+                               reg = <0x30000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "factory";
+                               reg = <0x40000 0x10000>;
+                               read-only;
+
+                               nvmem-layout {
+                                       compatible = "fixed-layout";
+                                       #address-cells = <1>;
+                                       #size-cells = <1>;
+
+                                       eeprom_factory_0: eeprom@0 {
+                                               reg = <0x0 0x400>;
+                                       };
+
+                                       eeprom_factory_8000: eeprom@8000 {
+                                               reg = <0x8000 0x4da8>;
+                                       };
+                               };
+                       };
+
+                       partition@50000 {
+                               compatible = "denx,uimage";
+                               label = "firmware";
+                               reg = <0x50000 0x7a0000>;
+                       };
+
+                       partition@ff0000 {
+                               label = "bdinfo";
+                               reg = <0x7f0000 0x10000>;
+                               read-only;
+
+                               nvmem-layout {
+                                       compatible = "fixed-layout";
+                                       #address-cells = <1>;
+                                       #size-cells = <1>;
+
+                                       macaddr_bdinfo_de00: macaddr@de00 {
+                                               compatible = "mac-base";
+                                               reg = <0xde00 0x6>;
+                                               #nvmem-cell-cells = <1>;
+                                       };
+                               };
+                       };
+               };
+       };
+};

diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk
index 50c8ed726fdb1523966dfd61664aa9743f60f69f..e379f253d42d1040bc8def6119cd55db95099949 100644 (file)
--- a/target/linux/ramips/image/mt76x8.mk
+++ b/target/linux/ramips/image/mt76x8.mk
@@ -199,6 +199,17 @@ define Device/creality_wb-01
 endef
 TARGET_DEVICES += creality_wb-01
 
+define Device/cudy_lt400e-v1
+  IMAGE_SIZE := 7808k
+  DEVICE_VENDOR := Cudy
+  DEVICE_MODEL := LT400E
+  DEVICE_VARIANT := v1
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-net-cdc-ether \
+  kmod-usb-serial-option
+  SUPPORTED_DEVICES += cudy,lt400e
+endef
+TARGET_DEVICES += cudy_lt400e-v1
+
 define Device/cudy_m1200-v1
   IMAGE_SIZE := 15872k
   DEVICE_VENDOR := Cudy

diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
index 94855c5ff7a581ca74be0e775743dcb706e77573..c44975ae462c115b62a8e5761734bd028b74f40c 100644 (file)
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
@@ -27,6 +27,14 @@ yuncore,m300)
 creality,wb-01)
        ucidef_set_led_switch "lan" "lan" "blue:lan" "switch0" "0x1"
        ;;
+cudy,lt400e-v1)
+       ucidef_set_led_switch "lan1" "lan1" "blue:lan-1" "switch0" "0x08"
+       ucidef_set_led_switch "lan2" "lan2" "blue:lan-2" "switch0" "0x04"
+       ucidef_set_led_switch "lan3" "lan3" "blue:lan-3" "switch0" "0x02"
+       ucidef_set_led_switch "lan4" "lan4" "blue:lan-4" "switch0" "0x01"
+       ucidef_set_led_netdev "wifi" "wifi" "blue:wlan" "phy0-ap0"
+       ucidef_set_led_netdev "internet" "internet" "blue:internet" "usb0"
+       ;;
 cudy,wr1000)
        ucidef_set_led_switch "wan" "wan" "blue:wan" "switch0" "0x10"
        ucidef_set_led_switch "lan1" "lan1" "blue:lan1" "switch0" "0x08"

diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
index 832207dcf1f98e5db65d3cfefb1415672b547993..f0d86bb366820709d6a8da1edc0c9a9fb7e01e55 100644 (file)
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
@@ -100,6 +100,13 @@ ramips_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "4:lan" "6@eth0"
                ;;
+       cudy,lt400e-v1)
+               ucidef_add_switch "switch0" \
+                       "3:lan:1" "2:lan:2" "1:lan:3" "0:lan:4" "6@eth0"
+               ucidef_set_interface "wwan" device "usb0" protocol "dhcp"
+               uci add_list firewall.@zone[1].network='wwan'
+               uci add_list firewall.@zone[1].network='wwan6'
+               ;;
        cudy,m1200-v1|\
        cudy,tr1200-v1)
                ucidef_add_switch "switch0" \